Nissan Pathfinder (2012 year). Manual - part 580

 

  Index      Manuals     Nissan Pathfinder (2012 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     578      579      580      581     ..

 

 

Nissan Pathfinder (2012 year). Manual - part 580

 

 

P0734 4GR INCORRECT RATIO

TM-67

< DTC/CIRCUIT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

If “TESTING” does not appear on CONSULT for a long time, select “SELF-DIAG RESULTS”. In case

a 1st trip DTC other than P0734 is shown, refer to “

TM-37, "CONSULT Function (TRANSMIS-

SION)"

”.

If “COMPLETED RESULT NG” is detected, go to

TM-67, "Diagnosis Procedure"

.

If “STOP VEHICLE” is detected, go to the following step.

6. Stop vehicle.

7. Drive vehicle in “D” position allowing it to shift from 1GR to 5GR and check shift timing and shift shock.

-

Touch “OK” to complete the inspection when normally shifted from the 1GR to 5GR.

-

Touch “NG” when an unusual shift shock, etc. occurs in spite of shifting from the 1GR to 5GR. Go to 

TM-

167, "Check Before Engine Is Started"

.

-

Perform 

TM-37, "CONSULT Function (TRANSMISSION)"

 when not shifted from the 1GR to 5GR. (Neither

“OK” nor “NG” are indicated.)

Diagnosis Procedure

INFOID:0000000007357168

1.

CHECK CAN COMMUNICATION LINE

Perform self-diagnosis. Refer to 

TM-37, "CONSULT Function (TRANSMISSION)"

TM-42, "Diagnosis Proce-

dure without CONSULT"

.

Is a malfunction in the CAN communication indicated in the results?

YES

>> Check CAN communication line. Refer to 

TM-47, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-101, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTION ITEM

Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

REPLACE CONTROL VALVE WITH TCM

1. Replace control valve with TCM. Refer to 

TM-176, "Removal and Installation"

.

2. Perform 

TM-66, "DTC Confirmation Procedure"

.

OK or NG

OK

>>

INSPECTION END

NG

>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to 

TM-167,

"Check Before Engine Is Started"

.

August 2012

2012 Pathfinder

TM-68

< DTC/CIRCUIT DIAGNOSIS >

P0735 5GR INCORRECT RATIO

P0735 5GR INCORRECT RATIO

Description

INFOID:0000000007357169

This malfunction is detected when the A/T does not shift into 5GR position as instructed by TCM. This is not

only caused by electrical malfunction (circuits open or shorted) but also by mechanical malfunction such as

control valve sticking, improper solenoid valve operation.

On Board Diagnosis Logic

INFOID:0000000007357170

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P0735” with CONSULT or 22nd judgment flicker without CONSULT is detected

when TCM detects any inconsistency in the actual gear ratio.

Possible Cause

INFOID:0000000007357171

• Harness or connectors 

(Solenoid circuits are open or shorted.)

• Input clutch solenoid valve

• Front brake solenoid valve

• Direct clutch solenoid valve

• High and low reverse clutch solenoid valve

• Each clutch

• Hydraulic control circuit

DTC Confirmation Procedure

INFOID:0000000007357172

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and

wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT

1. Start the engine and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.

2. Make sure that “ATF TEMP 1” is within the following range.

ATF TEMP 1: 20 – 140

°

C (68 – 284

°

F)

 

If out of range, drive vehicle to warm ATF or stop engine to cool ATF.

3. Select “5TH GR FNCTN P0735” of “DTC & SRT CONFIRMATION” mode for “TRANSMISSION” with

CONSULT.

4. Drive vehicle and maintain the following conditions.

With manual mode:

MANU MODE SW: ON

GEAR: “5” position

ACCELE POSI: 0.6/8 or more

VEHICLE SPEED: 10 km/h (6 MPH) or more

ENGINE SPEED: INPUT SPEED 

 50 rpm or more

INPUT SPEED: 300 rpm or more

Without manual mode:

SLCT LVR POSI: “D” position

GEAR: “5” position

ACCELE POSI: 0.6/8 or more

VEHICLE SPEED: 10 km/h (6 MPH) or more

ENGINE SPEED: INPUT SPEED 

 50 rpm or more

INPUT SPEED: 300 rpm or more

5. Keep the current driving status for at least 5 consecutive seconds if CONSULT screen changes from

“OUT OF CONDITION” to “TESTING”.

CAUTION:

August 2012

2012 Pathfinder

P0735 5GR INCORRECT RATIO

TM-69

< DTC/CIRCUIT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

If “TESTING” does not appear on CONSULT for a long time, select “SELF-DIAG RESULTS”. In case

a 1st trip DTC other than P0735 is shown, refer to “

TM-37, "CONSULT Function (TRANSMIS-

SION)"

”.

If “COMPLETED RESULT NG” is detected, go to 

TM-69, "Diagnosis Procedure"

.

If “STOP VEHICLE” is detected, go to the following step.

6. Stop vehicle.

7. Drive vehicle in “D” position allowing it to shift from 1GR to 5GR and check shift timing and shift shock.

-

Touch “OK” to complete the inspection when normally shifted from the 1GR to 5GR.

-

Touch “NG” when an unusual shift shock, etc. occurs in spite of shifting from the 1GR to 5GR. Go to 

TM-

167, "Check Before Engine Is Started"

.

-

Perform 

TM-37, "CONSULT Function (TRANSMISSION)"

 when not shifted from the 1GR to 5GR. (Neither

“OK” nor “NG” are indicated.)

Diagnosis Procedure

INFOID:0000000007357173

1.

CHECK CAN COMMUNICATION LINE

Perform self-diagnosis. Refer to 

TM-37, "CONSULT Function (TRANSMISSION)"

TM-42, "Diagnosis Proce-

dure without CONSULT"

.

Is a malfunction in the CAN communication indicated in the results?

YES

>> Check CAN communication line. Refer to 

TM-47, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-101, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTION ITEM

Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

REPLACE CONTROL VALVE WITH TCM

1. Replace control valve with TCM. Refer to 

TM-176, "Removal and Installation"

.

2. Perform 

TM-68, "DTC Confirmation Procedure"

.

OK or NG

OK

>>

INSPECTION END

NG

>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to 

TM-167,

"Check Before Engine Is Started"

.

August 2012

2012 Pathfinder

TM-70

< DTC/CIRCUIT DIAGNOSIS >

P0740 TORQUE CONVERTER

P0740 TORQUE CONVERTER

Description

INFOID:0000000007357174

• The torque converter clutch solenoid valve is activated, with the gear in D

4

, D

5

 by the TCM in response to

signals sent from the output speed sensor and accelerator pedal position sensor (throttle position sensor).

Torque converter clutch piston operation will then be controlled.

• Lock-up operation, however, is prohibited when A/T fluid temperature is too low.

• When the accelerator pedal is depressed (less than 1/8) in lock-up condition, the engine speed should not

change abruptly. If there is a big jump in engine speed, there is no lock-up.

CONSULT Reference Value in Data Monitor Mode

INFOID:0000000007357175

On Board Diagnosis Logic

INFOID:0000000007357176

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P0740” with CONSULT or 3rd judgment flicker without CONSULT is detected under

the following conditions.

- When TCM detects an improper voltage drop when it tries to operate the solenoid valve.

- When TCM detects as irregular by comparing target value with monitor value.

Possible Cause

INFOID:0000000007357177

• Torque converter clutch solenoid valve

• Harness or connectors

(The solenoid circuit is open or shorted.)

DTC Confirmation Procedure

INFOID:0000000007357178

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT

1. Turn ignition switch “ON”. (Do not start engine.)

2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.

3. Start engine and maintain the following conditions for at least 5 consecutive seconds.

VHCL/S SE-A/T: 80 km/h (50 MPH) or more

ACCELE POSI: 0.5/8 - 1.0/8

SLCT LVR POSI: “D” position 

Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving

conditions required for this test.

4. If DTC is detected go to 

TM-70, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT”.

Diagnosis Procedure

INFOID:0000000007357179

1.

CHECK INPUT SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.

Item name 

Condition 

Display value (Approx.)

TCC SOLENOID

When performing slip lock-up

0.2 - 0.4 A

When performing lock-up

0.4 - 0.6 A

August 2012

2012 Pathfinder

P0740 TORQUE CONVERTER

TM-71

< DTC/CIRCUIT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

3. Start engine.

4. Read out the value of “TCC SOLENOID” while driving.
OK or NG

OK

>> GO TO 4.

NG

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-101, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Check the following.

• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-176, "Removal and Installation"

.

NG

>> Repair or replace damaged parts.

4.

CHECK DTC

Perform “DTC Confirmation Procedure”.

• Refer to 

TM-70, "DTC Confirmation Procedure"

.

OK or NG

OK

>>

INSPECTION END

NG

>> GO TO 2.

August 2012

2012 Pathfinder

TM-72

< DTC/CIRCUIT DIAGNOSIS >

P0744 TORQUE CONVERTER

P0744 TORQUE CONVERTER

Description

INFOID:0000000007357180

This malfunction is detected when the A/T does not lock-up. This is not only caused by electrical malfunction

(circuits open or shorted) but also by mechanical malfunction such as control valve sticking, improper solenoid

valve operation, etc.

CONSULT Reference Value in Data Monitor Mode

INFOID:0000000007357181

On Board Diagnosis Logic

INFOID:0000000007357182

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P0744” with CONSULT or 3rd judgment flicker without CONSULT is detected under

the following conditions.

- When A/T cannot perform lock-up even if electrical circuit is good.

- When TCM detects as irregular by comparing difference value with slip rotation.

Possible Cause

INFOID:0000000007357183

• Harness or connectors

(The solenoid circuit is open or shorted.)

• Torque converter clutch solenoid valve

• Hydraulic control circuit

DTC Confirmation Procedure

INFOID:0000000007357184

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT

1. Start engine.

2. Select “DATA MONITOR" mode for "TRANSMISSION" with CONSULT.

3. Drive vehicle and maintain the following conditions for at least 30 consecutive seconds. 

ACCELE POSI: More than 1.0/8 

SLCT LVR POSI: “D” position 

TCC SOLENOID: 0.4 - 0.6 A

VEHICLE SPEED: 80 km/h (50 MPH) or more

Driving locations: Driving the vehicle uphill (increased engine load) will help maintain the driving

conditions required for this test.

4. If DTC is detected, go to 

TM-72, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT”.

Diagnosis Procedure

INFOID:0000000007357185

1.

CHECK INPUT SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.

3. Start the engine.

Item name

Condition 

Display value (Approx.)

TCC SOLENOID

When performing slip lock-up

0.2 - 0.4 A

When performing lock-up

0.4 - 0.6 A

August 2012

2012 Pathfinder

P0744 TORQUE CONVERTER

TM-73

< DTC/CIRCUIT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

4. Read out the value of “TCC SOLENOID” while driving.
OK or NG

OK

>> GO TO 4.

NG

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-101, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Check the following.

• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-176, "Removal and Installation"

.

NG

>> Repair or replace damaged parts.

4.

CHECK DTC

Perform “DTC Confirmation Procedure”.

• Refer to 

TM-72, "DTC Confirmation Procedure"

.

OK or NG

OK

>>

INSPECTION END

NG

>> GO TO 2.

August 2012

2012 Pathfinder

TM-74

< DTC/CIRCUIT DIAGNOSIS >

P0745 PRESSURE CONTROL SOLENOID A

P0745 PRESSURE CONTROL SOLENOID A

Description

INFOID:0000000007357186

The line pressure solenoid valve regulates the oil pump discharge pressure to suit the driving condition in

response to a signal sent from the TCM.

CONSULT Reference Value in Data Monitor Mode

INFOID:0000000007357187

On Board Diagnosis Logic

INFOID:0000000007357188

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P0745” with CONSULT or 4th judgment flicker without CONSULT is detected under

the following conditions.

- When TCM detects an improper voltage drop when it tries to operate the solenoid valve.

- When TCM detects as irregular by comparing target value with monitor value.

Possible Cause

INFOID:0000000007357189

• Harness or connectors

(The solenoid circuit is open or shorted.)

• Line pressure solenoid valve

DTC Confirmation Procedure

INFOID:0000000007357190

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT

1. Turn ignition switch “ON” and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.

2. Engine start and wait at least 5 second.

3.  If DTC is detected, go to 

TM-74, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT”.

Diagnosis Procedure

INFOID:0000000007357191

1.

CHECK INPUT SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT.

3. Start the engine.

4. Read out the value of “LINE PRES SOL” while driving.
OK or NG

OK

>> GO TO 4.

NG

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-101, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Item name

Condition 

Display value (Approx.)

LINE PRES SOL

During driving

0.2 - 0.6 A

August 2012

2012 Pathfinder

 

 

 

 

 

 

 

Content      ..     578      579      580      581     ..