Nissan Pathfinder (2006 year). Manual - part 395

 

  Index      Manuals     Nissan Pathfinder (2006 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     393      394      395      396     ..

 

 

Nissan Pathfinder (2006 year). Manual - part 395

 

 

OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

SRS-59

C

D

E

F

G

I

J

K

L

M

A

B

SRS

2006 Pathfinder

OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

PFP:98852

Removal and Installation

EHS001ME

The occupant classification control unit, occupant classification (pressure) sensor, and bladder are an integral
part of the front passenger seat cushion and are replaced as an assembly. Refer to 

SE-96, "REMOVAL"

  to

remove the seat, and 

SE-97, "REMOVAL"

  to replace the seat cushion.

SRS-60

COLLISION DIAGNOSIS

2006 Pathfinder

COLLISION DIAGNOSIS

PFP:00015

For Frontal Collision

EHS001S9

Check the SRS components using the following table.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRS-20, "SRS Operation Check"

 .

SRS INSPECTION (FOR FRONTAL COLLISION)

Part

SRS is activated

SRS is NOT activated

Driver air bag module

If the driver air bag 
has deployed:
REPLACE
Install with new fas-
teners.

If the driver air bag has NOT been activated:

1. Remove driver air bag module. Check harness cover and connectors for damage, 

terminals for deformities, and harness for binding.

2. Install driver air bag module into the steering wheel to check fit and alignment with 

the wheel.

3. If no damage is found, reinstall with new fasteners.

4. If damaged—REPLACE. Install driver air bag modules with new fasteners.

Front passenger air 
bag module

If the front passenger 
air bag has deployed:
REPLACE
Install with new fas-
teners.

If the front passenger air bag has NOT been activated:

1. Remove front passenger air bag module. Check harness cover and connectors for 

damage, terminals for deformities, and harness for binding.

2. Install front passenger air bag module into the instrument panel to check fit with the 

instrument panel.

3. If no damage is found, reinstall with new fasteners.

4. If damaged—REPLACE. Install front passenger air bag modules with new fasten-

ers.

Crash zone sensor

If any of the front air 
bags or seat belt pre-
tensioners* have 
been activated:
REPLACE the crash 
zone sensor and 
bracket with new fas-
teners.

*: Confirm seat belt 
pre-tensioner activa-
tion using CONSULT-
II only.

If the front air bags or seat belt pre-tensioners have NOT been activated:

1. Remove the crash zone sensor. Check harness connectors for damage, terminals 

for deformities, and harness for binding.

2. Check for visible signs of damage (dents, cracks, deformation) of the crash zone 

sensor and bracket.

3. Install the crash zone sensor to check fit.

4. If no damage is found, reinstall with new fasteners.

5. If damaged—REPLACE the crash zone sensor and bracket with new fasteners. 

Seat belt pre-ten-
sioner assemblies
(All applicable loca-
tions: buckle, reel, lap 
outer)

If either the driver or 
passenger seat belt 
pre-tensioner* has 
been activated:
REPLACE all seat 
belt pre-tensioner 
assemblies with new 
fasteners.

*: Confirm seat belt 
pre-tensioner activa-
tion using CONSULT-
II only.

If the pre-tensioners have NOT been activated:

1. Remove seat belt pre-tensioners.

Check harness cover and connectors for damage, terminals for deformities, and 
harness for binding.

2. Check belts for damage and anchors for loose mounting.

3. Check retractor for smooth operation.

4. Check seat belt adjuster for damage.

5. Check for deformities of the center pillar inner.

6. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner 

assembly.

7. If no damage is found, reinstall seat belt pre-tensioner assembly.

8. If damaged—REPLACE. Install the seat belt pre-tensioners with new fasteners. 

Diagnosis sensor unit

If any of the SRS 
components have 
been activated:
REPLACE the diag-
nosis sensor unit.
Install with new fas-
teners.

If none of the SRS components have been activated:

1. Check case for dents, cracks or deformities.

2. Check connectors for damage, and terminals for deformities.

3. If no damage is found, reinstall with new fasteners.

4. If damaged—REPLACE. Install diagnosis sensor unit with new fasteners.

COLLISION DIAGNOSIS

SRS-61

C

D

E

F

G

I

J

K

L

M

A

B

SRS

2006 Pathfinder

For Side and Rollover Collision

EHS001SA

Check the SRS components using the following table.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRS-20, "SRS Operation Check"

 .

WHEN SRS IS ACTIVATED IN THE SIDE OR ROLLOVER COLLISION

1.

Replace the following components:

Front seat back assembly (on the side on which side air bag is activated)

Diagnosis sensor unit

(LH or RH) side air bag (satellite) sensor (on the side on which side air bag is activated)

2.

Check the SRS components and the related parts using the following table.

Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,
deformation).

3.

Conduct self-diagnosis using CONSULT-II and “AIR BAG” warning lamp. Refer to 

SRS-20, "SRS Opera-

tion Check"

  for details. Ensure entire SRS operates properly.

WHEN SRS IS NOT ACTIVATED IN THE SIDE OR ROLLOVER COLLISION

1.

Check the SRS components and the related parts using the following table.

If the front seat back assembly is damaged, the front seat back assembly must be replaced.

2.

Conduct self-diagnosis using CONSULT-II and “AIR BAG” warning lamp. Refer to 

SRS-20, "SRS Opera-

tion Check"

  for details. Ensure entire SRS operates properly.

Steering wheel

1. Visually check steering wheel for deformities.

2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.

3. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

4. Check steering wheel for excessive free play.

5. If no damage is found, reinstall.

6. If damaged—REPLACE.

Spiral cable

If the driver front air 
bag has deployed:
REPLACE the spiral 
cable.

If the driver front air bag has not deployed:

1. Visually check spiral cable and combination switch for damage.

2. Check connectors and protective tape for damage.

3. Check steering wheel for noise, binding or heavy operation.

4. If no damage is found, reinstall.

5. If damaged—REPLACE.

Occupant classifica-
tion system (Passen-
ger seat)

1. Remove passenger seat.

2. Check control unit case for dents, cracks of deformities.

3. Check connectors and pressure sensor tube for damage, and terminals for deformities.

4. Check seat frame and cushion pan for dents or deformities.

5. If no damage is found, reinstall seat with new fasteners.

6. If damaged — REPLACE seat cushion assembly with new fasteners.

Harness and connec-
tors

1. Check connectors for poor connection, damage, and terminals for deformities.

2. Check harness for binding, chafing, cuts, or deformities.

3. If no damage is found, reinstall the harness and connectors.

4. If damaged—REPLACE the damaged harness. Do not attempt to repair, splice or modify any SRS harness.

Instrument panel

If the passenger front 
air bag has deployed: 
REPLACE the instru-
ment panel assembly.

If the passenger front air bag has NOT deployed:

1. Visually check instrument panel for damage.

2. If no damage is found, reinstall the instrument panel.

3. If damaged—REPLACE the instrument panel.

Part

SRS is activated

SRS is NOT activated

SRS-62

COLLISION DIAGNOSIS

2006 Pathfinder

SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)

Part

SRS is activated

SRS is NOT activated

LH side curtain air 
bag module

If the LH side curtain 
air bag has deployed:
REPLACE the LH 
side curtain air bag 
module. (Repair the 
center pillar inner, etc. 
before installing new 
one if damaged.)

If the LH side curtain air bag has NOT deployed:

1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on 

the collision side.

2. If damaged—Remove the LH side curtain air bag module.

3. Check for visible signs of damaged (tears etc.) of the LH side curtain air bag mod-

ule.

4. Check harness and connectors for damage, and terminals for deformities.

5. If no damage is found, reinstall the LH side curtain air bag module with new fasten-

ers.

6. If damaged—REPLACE the LH side curtain air bag module with new fasteners. 

RH side curtain air 
bag module

If the RH side curtain 
air bag has deployed:
REPLACE the RH 
side curtain air bag 
module. (Repair the 
center pillar inner, etc. 
before installing new 
one if damaged.)

If the RH side curtain air bag has NOT deployed:

1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on 

the collision side.

2. If damaged—Remove the RH side curtain air bag module.

3. Check for visible signs of damaged (tears etc.) of the RH side curtain air bag mod-

ule.

4. Check harness and connectors for damage, and terminals for deformities.

5. If no damage is found, reinstall the RH side curtain air bag module with new fasten-

ers.

6. If damaged—REPLACE the RH side curtain air bag module with new fasteners. 

Front LH side air bag 
module

If the front LH side air 
bag has deployed: 
REPLACE front LH 
seatback assembly.

If the front LH side air bag has NOT deployed: 

1. Check for visible signs of damage (dents, tears, deformation) of the seat back on 

the collision side.

2. Check harness and connectors for damage, and terminals for deformities.

3. If damaged—REPLACE the front LH seatback assembly. 

Front RH side air bag 
module

If the front RH side air 
bag has deployed:
REPLACE front RH 
seatback assembly.

If the front RH side air bag has NOT deployed:

1. Check for visible signs of damage (dents, tears, deformation) of the seat back on 

the collision side.

2. Check harness and connectors for damage, and terminals for deformities.

3. If damaged—REPLACE the front RH seatback assembly. 

(LH or RH) side air 
bag (satellite) sensor 

If any of the SRS 
components have 
deployed:
REPLACE the side 
air bag (satellite) sen-
sor on the collision 
side with new fasten-
ers. (Repair the cen-
ter pillar inner, etc. 
before installing new 
one if damaged.)

If none of the SRS components have been activated:

1. Remove the side air bag (satellite) sensor on the collision side. Check harness 

connectors for damage, terminals for deformities, and harness for binding.

2. Check for visible signs of damage (dents, cracks, deformation) of the side air bag 

(satellite) sensor.

3. Install the side air bag (satellite) sensor to check fit.

4. If no damage is found, reinstall the side sir bag (satellite) sensor with new fasten-

ers.

5. If damaged—REPLACE the side air bag (satellite) sensor with new fasteners.

Diagnosis sensor unit

If any of the SRS 
components have 
deployed:
REPLACE the diag-
nosis sensor unit with 
new fasteners.

If none of the SRS components have been activated:

1. Check case and bracket for dents, cracks or deformities.

2. Check connectors for damage, and terminals for deformities.

3. If no damage is found, reinstall the diagnosis sensor unit with new fasteners.

4. If damaged—REPLACE the diagnosis sensor unit with new fasteners.

COLLISION DIAGNOSIS

SRS-63

C

D

E

F

G

I

J

K

L

M

A

B

SRS

2006 Pathfinder

Seat belt pre-ten-
sioner assemblies
(All applicable loca-
tions: buckle, reel, lap 
outer)

If either the driver or 
passenger seat belt 
pre-tensioner* has 
been activated:
REPLACE all seat 
belt pre-tensioner 
assemblies with new 
fasteners.

*: Confirm seat belt 
pre-tensioner activa-
tion using CONSULT-
II only.

If the pre-tensioners have NOT been activated:

1. Remove seat belt pre-tensioners.

Check harness cover and connectors for damage, terminals for deformities, and 
harness for binding.

2. Check belts for damage and anchors for loose mounting.

3. Check retractor for smooth operation.

4. Check seat belt adjuster for damage.

5. Check for deformities of the center pillar inner.

6. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner 

assembly.

7. If no damage is found, reinstall seat belt pre-tensioner assembly.

8. If damaged—REPLACE. Install the seat belt pre-tensioners with new fasteners. 

Seat (with front side 
air bag)

If either the front LH 
or front RH side air 
bag modules has 
been deployed: 
REPLACE front seat-
back assembly on the 
deployed side.

If the front LH or front RH side air bag modules have NOT deployed: 

1. Visually check the seat on the collision side.

2. Remove the seat on the collision side and check the following for damage and 

deformities.

Harness, connectors and terminals

Frame and recliner (for front and rear seat), and also adjuster and slides (for front 
seat)

3. If no damage is found, reinstall the seat.

4. If damaged—REPLACE the damaged seat parts using new fasteners. If the front 

seat back is damaged, the front seat back assembly must be replaced.

Center inner pillar

1. Check the center inner pillar on the collision side for damage (dents, cracks, deformation).

2. If damaged—REPAIR the center inner pillar.

Trim/headlining

1. Check for visible signs of damage (dents, cracks, deformation) of the interior trim on the collision side.

2. If damaged—REPLACE the damaged trim parts.

Part

SRS is activated

SRS is NOT activated

SRS-64

COLLISION DIAGNOSIS

2006 Pathfinder

WT-1

ROAD WHEELS & TIRES

E  SUSPENSION

CONTENTS

C

D

F

G

H

I

J

K

L

M

SECTION 

A

B

WT

2006 Pathfinder

PRECAUTIONS .......................................................... 2

Precautions for Supplemental Restraint System 
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2

PREPARATION ........................................................... 3

Special Service Tool  ................................................. 3
Commercial Service Tools ........................................ 3

NOISE, VIBRATION, AND HARSHNESS (NVH) 
TROUBLESHOOTING ................................................ 4

NVH Troubleshooting Chart  ..................................... 4

WHEEL ....................................................................... 5

Inspection ................................................................. 5

WHEEL AND TIRE ASSEMBLY ................................. 6

Balancing Wheels  .................................................... 6

WHEEL BALANCE REMOVAL  ............................. 6
WHEEL BALANCE INSTALLATION AND 
ADJUSTMENT ...................................................... 6

Rotation .................................................................... 7

LOW TIRE PRESSURE WARNING SYSTEM ............ 8

System Components  ................................................ 8
System Description  .................................................. 8

TRANSMITTER ..................................................... 8
REMOTE KEYLESS ENTRY RECEIVER  ............. 8
BCM (BODY CONTROL MODULE) ...................... 9
WARNING LAMP AND BUZZER  .......................... 9
DISPLAY UNIT (WITH NAVI)  ................................ 9

CAN COMMUNICATION  .......................................... 10

System Description  ................................................ 10

TROUBLE DIAGNOSES  ...........................................11

Wiring Diagram — T/WARN —  ...............................11
Terminal and Reference Value (BCM) .................... 13
ID Registration Procedure  ...................................... 14

ID REGISTRATION WITH TRANSMITTER 
ACTIVATION TOOL  ............................................ 14
ID REGISTRATION WITHOUT TRANSMITTER 
ACTIVATION TOOL  ............................................ 16

Transmitter Wake Up Operation ............................. 18

WITH TRANSMITTER ACTIVATION TOOL ........ 18

CONSULT-II Function (BCM)  ................................. 19
Self-Diagnosis ........................................................ 20

DESCRIPTION .................................................... 20
FUNCTION .......................................................... 20
 ............................................................................ 20

How to Perform Trouble Diagnosis for Quick and 
Accurate Repair ...................................................... 22

INTRODUCTION ................................................. 22
WORK FLOW  ...................................................... 22

Preliminary Check  .................................................. 23
Malfunction Code/Symptom Chart .......................... 24

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC 
ITEMS ........................................................................ 26

Inspection 1: Transmitter or Control Unit (BCM) ..... 26

MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 26

Inspection 2: Transmitter - 1  ................................... 26

MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 
42, 43, 44, 45, 46, 47 OR 48  ............................... 26

Inspection 3: Transmitter - 2  ................................... 27

MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 27

Inspection 4: Vehicle Speed Signal  ........................ 28

MALFUNCTION CODE NO. 52 ........................... 28

TROUBLE DIAGNOSIS FOR SYMPTOMS  .............. 29

Inspection 1: Warning Lamp Does Not Come On 
When Ignition Switch Is Turned On  ........................ 29
Inspection 2: Warning Lamp Stays On When Ignition 
Switch Is Turned On  ............................................... 30
Inspection 3: Warning Lamp Flashes When Ignition 
Switch Is Turned On  ............................................... 32
Inspection 4: Hazard Warning Lamp Flashes When 
Ignition Switch Is Turned On  .................................. 33
Inspection 5: “TIRE PRESSURE” Information In 
Display Unit Does Not Exist .................................... 34
Inspection 6: ID Registration Cannot Be Completed ... 35

REMOVAL AND INSTALLATION  ............................. 36

Transmitter (Pressure Sensor)  ............................... 36

REMOVAL ........................................................... 36
INSTALLATION ................................................... 36

SERVICE DATA AND SPECIFICATIONS (SDS)  ...... 38

Road Wheel ............................................................ 38
Tire ......................................................................... 38

WT-2

PRECAUTIONS

2006 Pathfinder

PRECAUTIONS

PFP:00001

Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT 
BELT PRE-TENSIONER”

EES002BS

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

 

 

 

 

 

 

 

Content      ..     393      394      395      396     ..