Nissan Teana J32. Manual - part 824

MWI

B2205 VEHICLE SPEED

MWI-39

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

B2205 VEHICLE SPEED

Description

INFOID:0000000003792558

Vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) via CAN communication
to combination meter.

DTC Logic

INFOID:0000000003792559

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000003792560

1.

PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Perform “Self Diagnostic Result” of ABS actuator and electric unit (control unit), and repair or replace malfunc-
tioning parts.

>> Refer to 

BRC-13, "CONSULT-III Function"

 (with ABS models) or 

BRC-80, "CONSULT-III Func-

tion"

 (with VDC models).

DTC

Display contents of 

CONSULT-III

Diagnostic item is detected when ...

Probable malfunction location

B2205

VEHICLE SPEED

An abnormal vehicle speed signal is input 
from ABS actuator and electric unit (control 
unit) for 2 seconds or more

• Wheel sensor
• ABS actuator and electric unit (control unit)

MWI-40

< COMPONENT DIAGNOSIS >

B2267 ENGINE SPEED

B2267 ENGINE SPEED

Description

INFOID:0000000003792561

The engine speed signal is transmitted from ECM to the combination meter via CAN communication.

DTC Logic

INFOID:0000000003792562

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000003792563

1.

PERFORM SELF-DIAGNOSIS OF ECM

Perform “Self Diagnostic Result” of ECM, and repair or replace malfunctioning parts.

>> Refer to 

EC-113, "CONSULT-III Function"

.

DTC

Display contents of 

CONSULT-III

Diagnostic item is detected when ...

Probable malfunction location

B2267

ENGINE SPEED

ECM continuously transmits abnormal engine 
speed signals for 2 seconds or more 

• Crankshaft position sensor (POS)
• ECM

MWI

B2268 WATER TEMP

MWI-41

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

B2268 WATER TEMP

Description

INFOID:0000000003792564

The engine coolant temperature signal is transmitted from ECM to the combination meter via CAN communi-
cation.

DTC Logic

INFOID:0000000003792565

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000003792566

1.

PERFORM SELF-DIAGNOSIS OF ECM

Perform “Self Diagnosis Result” of ECM, and repair or replace malfunctioning parts.

>> Refer to 

EC-113, "CONSULT-III Function"

.

DTC

Display contents of 

CONSULT-III

Diagnostic item is detected when ...

Probable malfunction location

B2268

WATER TEMP

ECM continuously transmits abnormal engine 
coolant temperature signals for 60 seconds or 
more 

• Engine coolant temperature sensor
• ECM

MWI-42

< COMPONENT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

COMBINATION METER

COMBINATION METER : Diagnosis Procedure

INFOID:0000000003792567

1.

CHECK FUSE

Check for blown fuses.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Be sure to eliminate cause of malfunction before installing new fuse.

2.

CHECK POWER SUPPLY CIRCUIT

Check voltage between combination meter harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check harness between combination meter and fuse.

3.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect combination meter connector.

3.

Check continuity between combination meter harness connector terminals and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

BCM (BODY CONTROL MODULE)

BCM (BODY CONTROL MODULE) : Diagnosis Procedure

INFOID:0000000003900505

1.

CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown.

Power source

Fuse No.

Battery

11

Ignition switch ON or START 

4

Terminals

Voltage

(Approx.)

(+)

(-)

Combination meter

Ground

Connector

Terminal

M34

1

Battery voltage

2

Terminals

Continuity

(+)

(-)

Combination meter

Ground

Connector

Terminal

M34

3

Existed

23