Nissan Teana J32. Manual - part 623

FRONT SUSPENSION MEMBER

FSU-17

< REMOVAL AND INSTALLATION >

C

D

F

G

H

I

J

K

L

M

A

B

FSU

N

O

P

NOTE:
Remove the steering knuckle and wheel bearing assembly, steering gear assembly and hydraulic line,
stabilizer bar, transverse link and engine mounting insulator as a unit from the vehicle.

18. Remove the following parts.

• Steering knuckle and wheel hub and bearing assembly: refer to 

FAX-8, "Exploded View"

.

• Steering gear assembly and hydraulic line: refer to 

ST-18, "Exploded View"

 and 

ST-34, "Exploded

View"

.

• Stabilizer bar: refer to 

FSU-14, "Exploded View"

.

• Transverse link: refer to 

FSU-12, "Exploded View"

.

• Engine mounting insulator: refer to 

EM-67, "Exploded View"

.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Perform final tightening of installation position between front suspension member and transverse links (rub-

ber bushing) under unladen condition with tires on level ground.

Inspection

INFOID:0000000003811128

INSPECTION AFTER REMOVAL

Check the front suspension member for significant deformation, cracks, or damages. Replace if necessary.

INSPECTION AFTER INSTALLATION

1.

Check wheel sensor harness for proper connection. Refer to 

BRC-57, "FRONT WHEEL SENSOR :

Exploded View"

 (without VDC), 

BRC-151, "FRONT WHEEL SENSOR : Exploded View"

 (with VDC).

2.

Check wheel alignment. Refer to 

FSU-7, "Wheel Alignment Inspection"

.

3.

Adjust the neutral position of the steering angle sensor. Refer to 

BRC-66, "ADJUSTMENT OF STEERING

ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"

.

FSU-18

< SERVICE DATA AND SPECIFICATIONS (SDS) 

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Alignment

INFOID:0000000003811129

Measure value under unladen* conditions.

*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Ball Joint

INFOID:0000000003811130

Wheel Height

INFOID:0000000003811131

Item

Standard

Camber
Degree minute (Decimal degree)

Minimum

–1

°

 10

′

 (–1.16

°

)

Nominal

–0

°

 25

′

 (–0.42

°

)

Maximum

0

°

 20

′

 (0.33

°

)

Left and right difference

0

°

 45

′

 (0.75

°

) or less

Caster
Degree minute (Decimal degree)

Minimum

4

°

 10

′

 (4.17

°

)

Nominal

4

°

 55

′

 (4.92

°

)

Maximum

5

°

 40

′

 (5.66

°

)

Left and right difference

0

°

 45

′

 (0.75

°

) or less

Kingpin inclination
Degree minute (Decimal degree)

Minimum

11

°

 55

′

 (11.92

°

)

Nominal

12

°

 40

′

 (12.67

°

)

Maximum

13

°

 25

′

 (13.41

°

)

Total toe-
in

Distance

Minimum

In 0.5 mm (0.020 in)

Nominal

In 1.5 mm (0.059 in)

Maximum

In 2.5 mm (0.098 in)

Angle (left wheel or right wheel)
Degree minute (Decimal degree)

Minimum

In 0

°

 02

′

 (0.04

°

)

Nominal

In 0

°

 04

′

 (0.07

°

)

Maximum

In 0

°

 06

′

 (0.10

°

)

Item

Standard

Swing torque

Transverse link

0.5 – 4.9 N·m (0.06 – 0.49 kg-m, 5 – 43 in-lb)

Measurement on spring balance

Transverse link

11.1 – 108.9 N (1.2 – 11.1 kg, 3 – 24 lb)

Rotating torque

Transverse link

0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)

Axial end play

0.1 mm (0.004 in)

Tire size

205/65R16

215/55R17

Engine

VQ25DE

VQ35DE

Grade

250XE

250XL-V6

250XV-V6

350XV-V6

Front (Hf)

712 mm (28.03 in)

711 mm (27.99 in)

710 mm (27.95 in)

SERVICE DATA AND SPECIFICATIONS (SDS)

FSU-19

< SERVICE DATA AND SPECIFICATIONS (SDS) 

C

D

F

G

H

I

J

K

L

M

A

B

FSU

N

O

P

Measure value under unladen* conditions.

*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Rear (Hr)

703 mm (27.68 in)

702 mm (27.64 in)

701 mm (27.60 in)

Tire size

205/65R16

215/55R17

Engine

VQ25DE

VQ35DE

Grade

250XE

250XL-V6

250XV-V6

350XV-V6

SFA818A

MODEL J32 SERIES

© 2008 NISSAN INTERNATIONAL SA

All rights reserved. No part of this Electronic Service Manual may be reproduced or stored in a retrieval system, or transmitted in any form,

or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan International

SA, Switzerland.

A GENERAL INFORMATION
B ENGINE

D TRANSMISSION

& DRIVELINE

E SUSPENSION

F BRAKES

G STEERING

H RESTRAINTS

I VENTILATION, HEATER

& AIR CONDITIONER

J BODY INTERIOR

K BODY EXTERIOR, DOOR,

ROOF & VEHICLE SECURITY

L DRIVER CONTROLS

M ELECTRICAL &

POWER CONTROL

N DRIVER INFORMATION

& MULTIMEDIA

P MAINTENANCE

GI

General Information

EM

Engine Mechanical

LU

Engine Lubrication System

CO

Engine Cooling System

EC

Engine Control System

FL

Fuel System

EX

Exhaust System

STR

Starting System

ACC

Accelerator Control System

TM

Transaxle & Transmission

FAX

Front Axle

RAX

Rear Axle

FSU

Front Suspension

RSU

Rear Suspension

WT

Road Wheels & Tires

BR

Brake System

PB

Parking Brake System

BRC

Brake Control System

ST

Steering System

STC

Steering Control System

SB

Seat Belt

SR

SRS Airbag

SRC

SRS Airbag Control System

VTL

Ventilation System

HA

Heater & Air Conditioning System

HAC

Heater & Air Conditioning Control System

INT

Interior

IP

Instrument Panel

SE

Seat

ADP

Automatic Drive Positioner

DLK

Door & Lock

SEC

Security Control System

GW

Glass & Window System

PWC Power Window Control System

RF

Roof

EXT

Exterior

MIR

Mirrors

EXL

Exterior Lighting System

INL

Interior Lighting System

WW

Wiper & Washer

DEF

Defogger

HRN

Horn

PWO Power Outlet

BCS

Body Control System

LAN

LAN System

PCS

Power Control System

CHG Charging System

PG

Power Supply, Ground & Circuit Elements

MWI

Meter, Warning Lamp & Indicator

WCS Warning Chime System

AV

Audio, Visual & Navigation System

MA

Maintenance

QUICK REFERENCE INDEX

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

M

Publication Number: 
SM8E00-1J32E0E