Index Nissan Nissan Teana J32 (2008 year) - Service and Repair Manual

Content .. 507 508 509 510 ..

Nissan Teana J32. Manual - part 509

EXL-6

BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON ....................................................

Description .............................................................

Diagnosis Procedure .............................................

PRECAUTION ............................................

PRECAUTIONS ...............................................

Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................

ON-VEHICLE MAINTENANCE ..................

HEADLAMP AIMING ADJUSTMENT .............

Description .............................................................

Aiming Adjustment Procedure (Low Beam) ...........

Aiming Adjustment Procedure (High Beam) ..........

FRONT FOG LAMP AIMING ADJUSTMENT .

Description .............................................................

Aiming Adjustment Procedure ...............................

ON-VEHICLE REPAIR ...............................

FRONT COMBINATION LAMP .......................

Exploded View .......................................................

Removal and Installation .......................................

Replacement .........................................................

Disassembly and Assembly ...................................

FRONT FOG LAMP .........................................

Exploded View .......................................................

Removal and Installation .......................................

Replacement .........................................................

OPTICAL SENSOR .........................................

Exploded View .......................................................

Removal and Installation .......................................

LIGHTING & TURN SIGNAL SWITCH ............

Exploded View ......................................................

Removal and Installation .......................................

HEADLAMP AIMING SWITCH .........................

Exploded View ......................................................

Removal and Installation .......................................

HAZARD SWITCH ............................................

Exploded View ......................................................

Removal and Installation .......................................

SIDE TURN SIGNAL LAMP .............................

Exploded View ......................................................

Removal and Installation .......................................

REAR COMBINATION LAMP ..........................

Exploded View ......................................................

Removal and Installation .......................................

Replacement .........................................................

HIGH-MOUNTED STOP LAMP ........................

Exploded View ......................................................

Removal and Installation .......................................

REAR FOG LAMP ............................................

Exploded View ......................................................

Removal and Installation .......................................

Replacement .........................................................

LICENSE PLATE LAMP ...................................

Exploded View ......................................................

Removal and Installation .......................................

Replacement .........................................................

SERVICE DATA AND SPECIFICATIONS
(SDS) .........................................................

SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................

Bulb Specifications ................................................

DIAGNOSIS AND REPAIR WORKFLOW

EXL-7

< BASIC INSPECTION >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORKFLOW

Work Flow

INFOID:0000000003773518

OVERALL SEQUENCE

DETAILED FLOW

1.

INTERVIEW FOR MALFUNCTION

Interview the symptom to the customer.

JPLIA0313GB

EXL-8

< BASIC INSPECTION >

[XENON TYPE]

DIAGNOSIS AND REPAIR WORKFLOW

>> GO TO 2.

2.

SYMPTOM CHECK

Check the symptom from the customer's information.

>> GO TO 3.

3.

BASIC INSPECTION

Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.

>> GO TO 4.

4.

SELF-DIAGNOSIS WITH CONSULT-III

Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?

YES

>> GO TO 5.

NO

>> GO TO 6.

5.

TROUBLE DIAGNOSIS BY DTC

Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.

>> GO TO 9.

6.

FAIL-SAFE ACTIVATION CHECK

Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?

YES

>> GO TO 7.

NO

>> GO TO 8.

7.

SYSTEM DIAGNOSIS

Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.

>> GO TO 9.

8.

SYMPTOM DIAGNOSIS

Perform the symptom diagnosis. Specify the malfunctioning part.

>> GO TO 9.

9.

MALFUNCTION PART REPAIR

Repair or replace the malfunctioning part.

>> GO TO 10.

10.

REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)

Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.

Is any DTC detected?

YES

>> GO TO 5.

NO

>> GO TO 11.

11.

REPAIR CHECK (OPERATION CHECK)

Check the operation of each part.
Does it operate normally?

YES

>> INSPECTION END

NO

>> GO TO 3.

INSPECTION AND ADJUSTMENT

EXL-9

< BASIC INSPECTION >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000003894984

CAUTION:

• When replacing the auto levelizer control unit, you must perform “WRITE CONFIGURATION” with

CONSULT-III.

- Complete the procedure of “WRITE CONFIGURATION” in order.
• When replacing the auto levelizer control unit, perform “SENSOR INITIALIZE” with CONSULT-III.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000003894985

1.

WRITING VEHICLE SPECIFICATION

CONSULT-III Configuration

Perform “WRITE CONFIGURATION” to write vehicle specification. Refer to

EXL-9, "CONFIGURATION

(HEADLAMP LEVELIZER) : Special Repair Requirement"

.

>> GO TO 2.

2.

SENSOR INITIALIZE

CONSULT-III Work support

Perform “SENSOR INITIALIZE”. Refer to

EXL-10, "SENSOR INITIALIZE : Special Repair Requirement

(HEADLAMP AIMING CONTROL SYSTEM)"

>> WORK END

CONFIGURATION (HEADLAMP LEVELIZER)

CONFIGURATION (HEADLAMP LEVELIZER) : Description

INFOID:0000000003894986

Vehicle specification needs to be written with CONSULT-III because it is not written after replacing the auto
levelizer control unit.

CAUTION:

• When replacing the auto levelizer control unit, you must perform “WRITE CONFIGURATION” with

CONSULT-III.

• Complete the procedure of “WRITE CONFIGURATION” in order.

CONFIGURATION (HEADLAMP LEVELIZER) : Special Repair Requirement

INFOID:0000000003894987

1.

WRITE CONFIGURATION

CONSULT-III Configuration

1.

Select “WRITE CONFIGURATION”.

2.

Select “Setting change”.

3.

When “COMMAND FINISHED”, select “END”.

>> WORK END

SENSOR INITIALIZE

Function

Description

WRITE CONFIGURATION

Writes the vehicle configuration automatically.

Content .. 507 508 509 510 ..