Murano Cross Cabriolet Z51 (2013 year). Manual

IP-8

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000008462958

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Service Procedure Precautions for Models with a Pop-up Roll Bar

INFOID:0000000008462959

WARNING:

Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll

over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.

• Before removing and installing the pop-up roll bar component parts and harness, always turn the

ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)

• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS

AIR BAG CONTROL warnings in the Service Manual.

Precaution

INFOID:0000000008462960

• Disconnect battery negative terminal in advance.
• Disconnect air bag system line in advance.
• Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
• Be careful not to scratch pad and other parts.
• When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which may

get in the way with a shop cloth.

• When removing parts with a screwdriver or other tool, cover the tool surface by vinyl tape to protect parts.
• Keep removed parts protected with a shop cloth.
• If a clip is deformed or damaged, replace it.

Revision: 2012 October

2013 Murano CrossCabriolet

PRECAUTIONS

IP-9

< PRECAUTION >

• If an unreusable part is removed, replace it with a new one.
• Tighten bolts and nuts firmly to the specified torque.
• After reassembly has been completed, make sure each part functions correctly.
• Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3%), dip the cloth, then clean off the stain with
the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
• Never use any organic solvent, such as thinner or benzine.

Revision: 2012 October

2013 Murano CrossCabriolet

IP-10

< PREPARATION >

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000008462961

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000008462962

Tool number

(Kent-Moore No.)

Tool name

Description

(J-39570)
Chassis ear

Locates the noise

(J-43980)
NISSAN Squeak and Rattle
Kit

Repairs the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Locates the noise

Remover tool

Removes clips, pawls, and metal clips

SIIA0995E

JMKIA3050ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

INSTRUMENT PANEL ASSEMBLY

IP-13

< REMOVAL AND INSTALLATION >

Removal and Installation

INFOID:0000000008462965

WORK STEP

When removing instrument panel assembly, combination meter, AV control unit (or audio unit), and front dis-
play unit take steps in the order shown by the number below.

Speaker grille RH

Center speaker grille

Speaker grille LH

Front squawker LH

Instrument side finisher LH

Switch bracket

Instrument lower panel LH

Fuse block lid

Steering column lower cover

10. Cluster lid C

11.

Cluster lid C (lower)

12. Illumination lamp

13. Socket and bulb

14. Glove box striker RH

15. Instrument lower panel RH

16. Socket and bulb

17. Glove box lamp

18. Glove box dumper

19. Instrument side finisher RH

20. Instrument panel assembly

21. Front squawker RH

22. Optical sensor

23. Center speaker

24. Sunload sensor

25. Security indicator

26. Combination meter

27. Cluster lid A

28. Steering column upper cover

29. Instrument stay cover LH

30. Instrument stay cover RH

31. Glove box lid

32. Passenger air bag module

33. Display unit

34. AV control unit

35. Cluster lid D

36. Glove box striker LH

37. Center ventilator assembly

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

PARTS

INSTRUMENT

PANEL ASSEMBLY

COMBINATION

METER

AV CONTROL

UNIT

(or AUDIO UNIT)

DISPLAY UNIT (or

AUDIO DISPLAY

UNIT)

Instrument side finisher LH

[1]

Front body side welt LH

[2]

Front pillar garnish LH

[3]

Speaker grille LH

[4]

Front squawker LH

[5]

Vehicle security indicator

[6]

Sunload sensor

[7]

Instrument lower panel LH

[8]

[2]

Driver air bag module

[9]

Steering wheel

[10]

Steering column cover

[11]

[3]

Combination switch

[12]

Spiral cable

[13]

Cluster lid A

[14]

[4]

Combination meter

[15]

[5]

Cluster lid C (lower)

[16]

Instrument stay cover LH

[17]

[1]

Instrument stay cover RH

[18]

[2]

Cluster lid D

[19]

[3]

Cluster lid C

[20]

[4]

AV control unit

[21]

[5]

Center ventilator assembly

[22]

[6]

Display unit

[23]

[7]

Revision: 2012 October

2013 Murano CrossCabriolet

IP-14

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

[ ]: Number indicates step in removal procedures.

WARNING:

Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.

CAUTION:

When removing, always use a remover tool that is made of plastic.

REMOVAL

Remove instrument side finisher LH.
1.

Insert a remover tool (A) into lower space.

Pull the instrument side finisher LH (1) crosswise.

Remove front body side welt LH. Refer to

INT-21, "BODY SIDE WELT : Removal and Installation"

Remove front pillar garnish LH. Refer to

INT-18, "FRONT PILLAR GARNISH : Removal and Installation"

Remove speaker grille LH.
1.

Pull up speaker grille LH (1) to disengage pawls.

Remove speaker grille LH.

Remove front squawker LH. Refer to

AV-106, "Removal and Installation"

Remove vehicle security indicator. Refer to

SEC-111, "Removal and Installation"

Remove sunload sensor. Refer to

HAC-82, "Removal and Installation"

Center speaker grille

[24]

Center speaker (BOSE audio with NAVI mod-
els)

[25]

Instrument side finisher RH

[26]

Front body side welt RH

[27]

Front pillar garnish RH

[28]

Speaker grille RH

[29]

Front squawker RH

[30]

Optical sensor (XENON headlamp models)

[31]

Instrument lower panel RH

[32]

Passenger air bag module harness connector

[33]

Passenger air bag module mounting bolt

[34]

Instrument panel assembly

[35]

: Pawl

JMJIA1314ZZ

: Pawl

JMJIA1315ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

INSTRUMENT PANEL ASSEMBLY

IP-15

< REMOVAL AND INSTALLATION >

Remove instrument lower panel LH.
1.

Remove hood opener lever fixing bolts (A).

Pull back instrument lower panel LH (1).

Release data link connector (pawl) then remove it from
instrument lower panel LH.

Disconnect harness connectors and aspirator duct.

Remove driver air bag module. Refer to

SR-11, "Removal and Installation"

10. Remove steering wheel. Refer to

ST-30, "Removal and Installation"

11. Remove steering column covers.

Remove steering column cover fixing screws (A).

Pull up steering column upper cover (1), and then remove
steering column upper cover.

Pull down steering column lower cover (2), and then remove
steering column lower cover.

12. Remove combination switch. Refer to

BCS-78, "Removal and Installation"

13. Remove spiral cable. Refer to

SR-14, "Removal and Installation"

14. Remove cluster lid A.

Pull back cluster lid A (1), and disengage clips and pawl.

Remove cluster lid A.

15. Remove combination meter. Refer to

MWI-70, "Removal and Installation"

: Clip

: Metal clip

JMJIA1316ZZ

: Pawl

JMJIA1317ZZ

: Clip

: Pawl

JMJIA1318ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

IP-16

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

16. Remove cluster lid C (lower).

Disengage cluster lid C (lower) (1) fixing clips and pawls
with remover tool (A).

Pull down cluster lid C (lower).

Disconnect illumination lamp harness connector.

17. Remove instrument stay cover LH.

Remove instrument stay cover LH (1) fixing screw (A).

Disengage instrument stay cover LH fixing clips and pawls
with remover tool.

Pull back and pull up instrument stay cover LH.

Disconnect push button ignition switch harness connector

18. Remove instrument stay cover RH.

Remove instrument stay cover RH (1) fixing screw (A).

Disengage instrument stay cover RH fixing clips and pawls
with remover tool.

Pull back and pull up instrument stay cover RH.

Disconnect hazard switch harness connector.

19. Remove cluster lid D.

Remove cluster lid D (1) fixing screws (A).

Pull back cluster lid D.

Disconnect harness connector.

20. Remove cluster lid C.

Remove cluster lid C (1) fixing screws (A).

Pull back cluster lid C.

Disconnect harness connectors.

: Clip

: Pawl

JMJIA1319ZZ

: Clip

: Pawl

JMJIA1320ZZ

: Clip

: Pawl

JMJIA1321ZZ

: Pawl

JMJIA1322ZZ

JMJIA1323ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

INSTRUMENT PANEL ASSEMBLY

IP-17

< REMOVAL AND INSTALLATION >

21. Remove AV control unit. Refer to

AV-102, "Removal and Installation"

22. Remove center ventilator assembly.

Remove center ventilator assembly (1) fixing screws (A).

Pull back center ventilator assembly.

23. Remove display unit. Refer to

AV-104, "Removal and Installation"

24. Remove center speaker grille.

Disengage center speaker grille (1) fixing clips with remover
tool (A).

Pull up center speaker grille.

25. Remove center speaker (BOSE audio with NAVI models). Refer to

AV-242, "Removal and Installation"

26. Remove instrument side finisher RH.

Insert a remover tool (A) into lower space.

Pull the instrument side finisher RH (1) crosswise.

27. Remove front body side welt RH. Refer to

INT-21, "BODY SIDE WELT : Removal and Installation"

28. Remove front pillar garnish RH. Refer to

INT-18, "FRONT PILLAR GARNISH : Removal and Installation"

29. Remove speaker grille RH.

Pull up speaker grille RH (1).

30. Remove front squawker RH. Refer to

AV-106, "Removal and Installation"

31. Remove optical sensor (XENON headlamp models). Refer to

EXL-75, "Removal and Installation"

: Clip

: Pawl

JMJIA1325ZZ

: Clip

JMJIA1327ZZ

: Pawl

JMJIA1328ZZ

: Pawl

JMJIA1329ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

IP-18

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

32. Remove instrument lower panel RH.

Remove instrument lower panel RH (1) fixing screws (A).

Open the glove box lid (2).

Remove instrument lower panel RH fixing screws (B).

Pull back instrument lower panel RH.

Disconnect harness connector.

33. Disconnect front passenger air bag module connector. Refer to

SR-17, "Removal and Installation"

34. Remove front passenger air bag module fixing bolt. Refer to

SR-17, "Exploded View"

35. Remove instrument panel assembly (1) mounting screws (A) and bolt (B).

36. Remove instrument panel assembly.

CAUTION:

• Cover center console upper surface with a shop cloth to prevent it from being damaged.
• When removing instrument panel assembly, 2 workers are required so as to prevent it from drop-

ping.

37. Remove the following parts after removing instrument panel assembly.

• Passenger air bag module. Refer to

SR-17, "Removal and Installation"

• Ventilator duct. Refer to

VTL-10, "SIDE VENTILATOR GRILLE : Removal and Installation"

• Upper ventilator duct. Refer to

VTL-11, "UPPER VENTILATOR DUCT : Removal and Installation"

• Defroster nozzle and side defroster nozzle LH/RH. Refer to

VTL-11, "DEFROSTER NOZZLE AND SIDE

DEFROSTER NOZZLE : Removal and Installation"

• Side defroster grille LH/RH. Refer to

VTL-10, "SIDE DEFROSTER GRILLE : Removal and Installation"

• Side ventilator grille LH/RH. Refer to

VTL-10, "SIDE VENTILATOR GRILLE : Removal and Installation"

• Antenna feeder

: Pawl

: Metal clip

JMJIA1330ZZ

JMJIA1331ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

INSTRUMENT PANEL ASSEMBLY

IP-19

< REMOVAL AND INSTALLATION >

- BOSE audio without navigation: Refer to

AV-122, "Feeder Layout"

- BOSE audio with navigation: Refer to

AV-255, "Feeder Layout"

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never use the steering wheel mounting nut after removal, replace with the new nut.
• Never use the driver air bag mounting bolts after removal, replace with the new bolts.
• Never use the passenger air bag mounting bolt after removal, replace with the new bolt.

Revision: 2012 October

2013 Murano CrossCabriolet

IP-20

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

CENTER CONSOLE ASSEMBLY

Exploded View

INFOID:0000000008462966

Instrument lower cover RH

Instrument lower cover LH

Instrument stay

Front console bracket

Console reinforcement

Lower console finisher LH

Console harness

Inside key antenna

Console rear finisher

10. Center console assembly

11.

Socket and bulb

12. Console finisher assembly

13. Cup holder assembly

14. Console pocket

15. Socket knob

16. Socket inner case

17. Console mat

18. Console switch finisher

19. Front console pocket

20. Lower console finisher RH

21. USB connector

22. Socket knob

23. Socket ring

24. Socket inner case

25. Lower console assembly

26. Auxiliary input jack

: Pawl

: Clip

: Metal clip

JMJIA6324ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

CENTER CONSOLE ASSEMBLY

IP-21

< REMOVAL AND INSTALLATION >

Removal and Installation

INFOID:0000000008462967

CAUTION:

When removing, always use a remover tool that is made of plastic.

REMOVAL

Remove selector lever knob. Refer to

TM-145, "Removal and Installation"

Remove console finisher assembly.
1.

Open the console lid.

Remove console finisher assembly (1) fixing pawls and
metal clips with remover tool (A).

Pull up console finisher assembly.

Disconnect harness connectors.

Remove front console pocket.
1.

Remove front console pocket (1) fixing screw (A).

Pull up front console pocket, and then disengage metal
clips.

Disconnect harness connectors.

Remove console rear finisher.
1.

Pull back console rear finisher.

Disconnect harness connector.

Remove center console assembly.
1.

Remove center console assembly (1) fixing screws (A).

Lift up back side and pull back.

: Pawl

: Metal clip

JMJIA1334ZZ

: Metal clip

JMJIA1335ZZ

: Metal clip

JMJIA6325ZZ

JMJIA1338ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

IP-22

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

Remove instrument lower cover LH and RH.
1.

Disengage instrument lower cover LH (1) fixing pawls and
clips.

Pull back instrument lower cover LH.

Disengage instrument lower cover RH (2) fixing pawls and
clips.

Pull the instrument lower cover RH crosswise.

Remove lower console finisher LH and RH.
1.

Remove lower console finisher LH (1) fixing screws (A).

Remove lower console finisher LH fixing clip (B).

Remove lower console finisher LH fixing clip (C).

Pull the console finisher LH crosswise.

Remove lower console finisher RH (2) fixing screws (D).

Remove lower console finisher RH fixing clip (E).

Remove lower console finisher RH fixing clip (F).

Pull the console finisher RH crosswise.

Remove lower console assembly.
1.

Remove lower console assembly (1) fixing screws (A).

Remove lower console assembly mounting bolts (B).

Disconnect harness connectors.

NOTE:
Remove following parts after removing lower console assembly.
• USB connector: Refer to

AV-114, "Removal and Installation"

• Auxiliary input jacks: Refer to

AV-113, "Removal and Installation"

• Console power socket: Refer to

PWO-4, "CONSOLE POWER SOCKET : Removal and Installation"

Remove CVT shift selector. Refer to

TM-145, "Removal and Installation"

10. Remove console reinforcement.

Remove console reinforcement (1) mounting nut (A).

Remove console reinforcement mounting bolts (B).

Remove harness clips.

11. Remove instrument stay mounting nuts, and then remove instrument stay.

12. Remove front console bracket mounting bolt and nut, and then remove front console bracket.

INSTALLATION

Install in the reverse order of removal.

: Clip

: Pawl

JMJIA1339ZZ

: Clip

JMJIA1340ZZ

JMJIA1341ZZ

: Clip

JMJIA1342ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

Murano Cross Cabriolet Z51 (2013 year). Manual - part 54