Murano Cross Cabriolet Z51 (2013 year). Manual - part 50

 

  Index      Manuals     Murano Cross Cabriolet Z51 (2013 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     48      49      50      51     ..

 

 

Murano Cross Cabriolet Z51 (2013 year). Manual - part 50

 

 

HAC-80

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

AMBIENT SENSOR

AMBIENT SENSOR

Exploded View

INFOID:0000000008460697

Removal and Installation

INFOID:0000000008460698

REMOVAL

Disconnect ambient sensor harness connector (A), and then remove
ambient sensor (1).

INSTALLATION

Install in the reverse order of removal.

1.

Ambient sensor

JPIIA1300ZZ

JPIIA0556ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

IN-VEHICLE SENSOR

HAC-81

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

IN-VEHICLE SENSOR

Exploded View

INFOID:0000000008460699

Removal and Installation

INFOID:0000000008460700

REMOVAL

1.

Remove instrument lower panel LH. Refer to 

IP-13, "Removal and Installation"

.

2.

Remove fixing screw (A), and then remove in-vehicle sensor (1).

INSTALLATION

Install in the reverse order of removal.

1.

In-vehicle sensor

2.

Instrument lower panel LH

JPIIA0557ZZ

JPIIA0558ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

HAC-82

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

SUNLOAD SENSOR

SUNLOAD SENSOR

Exploded View

INFOID:0000000008460701

Removal and Installation

INFOID:0000000008460702

REMOVAL

Disconnect sunload sensor harness connector, and then remove
sunload sensor (1).

INSTALLATION

Install in the reverse order of removal.

1.

Sunload sensor

JPIIA0559ZZ

JPIIA0560ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

INTAKE SENSOR

HAC-83

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

INTAKE SENSOR

Exploded View

INFOID:0000000008460703

Removal and Installation

INFOID:0000000008460704

REMOVAL

1.

Remove evaporator pipe assembly. Refer to 

HA-48, "EVAPORATOR PIPE ASSEMBLY : Removal and

Installation"

.

2.

Pull out evaporator (1) toward the right side of vehicle, and then
remove intake sensor (2).

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• Replace O-rings with new ones. Then apply the compressor oil to them when installing.
• Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor

can be located in the same position.

• Never rotate the bracket insertion part when removing and installing the intake sensor.

1.

Heater & cooling unit assembly

2.

Intake sensor bracket

3.

Intake sensor

4.

Evaporator assembly

5.

Evaporator cover

6.

Air mix door motor (Passenger side)

7.

Foot duct RH

8.

Cooler pipe grommet

JPIIA1303ZZ

JPIIA0907ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

HAC-84

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

INTAKE SENSOR

• Check for leakages when recharging refrigerant. Refer to 

HA-18, "Leak Test"

.

Revision: 2012 October

2013 Murano CrossCabriolet

REFRIGERANT PRESSURE SENSOR

HAC-85

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

REFRIGERANT PRESSURE SENSOR

Exploded View

INFOID:0000000008460705

Refer to 

HA-38, "Exploded View"

.

Removal and Installation

INFOID:0000000008460706

REMOVAL

Refer to 

HA-41, "REFRIGERANT PRESSURE SENSOR : Removal and Installation"

.

INSTALLATION

Install in the reverse order of removal.

Revision: 2012 October

2013 Murano CrossCabriolet

HAC-86

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

DOOR MOTOR

DOOR MOTOR

Exploded View

INFOID:0000000008460707

AIR MIX DOOR MOTOR

AIR MIX DOOR MOTOR : Removal and Installation

INFOID:0000000008460708

REMOVAL

Driver Side

1.

Set the temperature at full cold.

CAUTION:

The angle may be out, when installing the air mix door motor to the air mix door, unless the above
procedure is performed.

2.

Disconnect the battery cable from the negative terminal.

3.

Remove front foot duct LH. Refer to 

VTL-12, "FRONT FOOT DUCT : Removal and Installation"

.

4.

Disconnect air mix door motor harness connector.

1.

Intake door motor

2.

Blower unit assembly

3.

Mode door motor

4.

Main link

5.

Link rod

6.

Foot door link

7.

Max. cool door link

8.

Mode door lever

9.

Ventilator door link

10. Defroster door link

11.

Ventilator door lever

12. Foot door lever

13. Max. cool door lever

14.

Defroster door lever

15. Air mix door motor (Driver side)

16. Heater & cooling unit assembly

17.

Air mix door motor (Passenger side) 18. Upper ventilator door motor

19. Upper ventilator door rod

20.

Upper ventilator door lever

: Vehicle front

JPIIA1238ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

DOOR MOTOR

HAC-87

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

5.

Remove fixing screws (A), and then air mix door motor (1).

Passenger Side

1.

Set the temperature at full cold.

CAUTION:

The angle may be out, when installing the air mix door motor to the air mix door, unless the above
procedure is performed.

2.

Disconnect the battery cable from the negative terminal.

3.

Remove front foot duct RH. Refer to 

VTL-12, "FRONT FOOT DUCT : Removal and Installation"

.

4.

Disconnect air mix door motor harness connector.

5.

Remove fixing screws (A), and then air mix door motor (1).

INSTALLATION

Install in the reverse order of removal.

MODE DOOR MOTOR

MODE DOOR MOTOR : Removal and Installation

INFOID:0000000008460709

REMOVAL

1.

Remove instrument panel assembly. Refer to 

IP-13, "Removal and Installation"

. 

2.

Disconnect mode door motor harness connector.

3.

Remove fixing screws (A), and then remove mode door motor
(1).

INSTALLATION

Install in the reverse order of removal.

INTAKE DOOR MOTOR

JPIIA0577ZZ

JPIIA0578ZZ

JPIIA0575ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

HAC-88

< REMOVAL AND INSTALLATION >

[AUTOMATIC AIR CONDITIONING]

DOOR MOTOR

INTAKE DOOR MOTOR : Removal and Installation

INFOID:0000000008460710

REMOVAL

1.

Remove instrument lower panel RH. Refer to 

IP-13, "Removal and Installation"

. 

2.

Remove fixing screw (A), and then move key less controller
assembly bracket (1) to secure work space.

3.

Disconnect intake door motor harness connector.

4.

Remove fixing screws (A), and then remove intake door motor
(1).

INSTALLATION

Install in the reverse order of removal.

UPPER VENTILATOR DOOR MOTOR

UPPER VENTILATOR DOOR MOTOR : Removal and Installation

INFOID:0000000008460711

REMOVAL

1.

Remove blower unit assmbly. Refer to 

VTL-19, "Removal and Installation"

. 

2.

Disconnect upper ventilator door motor harness connector.

3.

Remove fixing screws (A), and then remove upper ventilator
door motor (1).

INSTALLATION

Install in the reverse order of removal.

JPIIA0569ZZ

JPIIA0570ZZ

JPIIA0574ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

HRN-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000008462239

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Revision: 2012 October

2013 Murano CrossCabriolet

HORN

HRN-3

< WIRING DIAGRAM >

C

D

E

F

G

H

I

J

K

M

A

B

HRN

N

O

P

WIRING DIAGRAM

HORN

Wiring Diagram

INFOID:0000000008462240

For connector terminal arrangements, harness layouts, and alphabets in a 

 (option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

JCLWA5340GB

Revision: 2012 October

2013 Murano CrossCabriolet

HRN-4

< REMOVAL AND INSTALLATION >

HORN

REMOVAL AND INSTALLATION

HORN

Exploded View

INFOID:0000000008462241

Removal and Installation

INFOID:0000000008462242

REMOVAL

1.

Remove the front grille. Refer to 

EXT-18, "Exploded View"

.

2.

Disconnect the horn (LOW, HIGH) connector.

3.

Remove the horn mounting nut, and remove the horn (LOW, HIGH) from the vehicle.

INSTALLATION

Install in the reverse order of removal.

1.

Horn (HIGH)

2.

Horn (LOW)

JPLIA1492ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

INL-1

DRIVER CONTROLS

C

D

E

F

G

H

I

J

K

M

SECTION 

INL

A

B

INL

N

O

P

CONTENTS

INTERIOR LIGHTING SYSTEM

PRECAUTION ...............................................

3

PRECAUTIONS ...................................................

3

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

3

Precaution for Battery Service  ..................................

3

Service Procedure Precautions for Models with a 
Pop-up Roll Bar .........................................................

3

SYSTEM DESCRIPTION  ..............................

4

COMPONENT PARTS  ........................................

4

INTERIOR LIGHTING SYSTEM ..................................

4

INTERIOR LIGHTING SYSTEM : Component 
Parts Location  ...........................................................

4

INTERIOR LIGHTING SYSTEM : 
Component Description ............................................

4

SYSTEM ..............................................................

6

INTERIOR ROOM LAMP CONTROL SYSTEM  ..........

6

INTERIOR ROOM LAMP CONTROL SYSTEM : 
System Diagram ........................................................

6

INTERIOR ROOM LAMP CONTROL SYSTEM : 
System Description  ...................................................

6

INTERIOR ROOM LAMP BATTERY SAVER SYS-
TEM ..............................................................................

7

INTERIOR ROOM LAMP BATTERY SAVER 
SYSTEM : System Diagram  ......................................

8

INTERIOR ROOM LAMP BATTERY SAVER 
SYSTEM : System Description  .................................

8

ILLUMINATION CONTROL SYSTEM  .........................

8

ILLUMINATION CONTROL SYSTEM : System 
Diagram .....................................................................

9

ILLUMINATION CONTROL SYSTEM : System 
Description ................................................................

9

DIAGNOSIS SYSTEM (BCM)  ............................

10

COMMON ITEM  .........................................................

10

COMMON ITEM : CONSULT Function (BCM - 
COMMON ITEM)  .....................................................

10

INT LAMP ...................................................................

11

INT LAMP : CONSULT Function (BCM - INT 
LAMP) ......................................................................

12

BATTERY SAVER  .....................................................

13

BATTERY SAVER : CONSULT Function (BCM - 
BATTERY SAVER) ..................................................

14

ECU DIAGNOSIS INFORMATION ..............

16

BCM ...................................................................

16

List of ECU Reference .............................................

16

WIRING DIAGRAM  ......................................

17

INTERIOR ROOM LAMP CONTROL SYSTEM 

...

17

Wiring Diagram ........................................................

17

ILLUMINATION .................................................

19

Wiring Diagram ........................................................

19

BASIC INSPECTION  ...................................

22

DIAGNOSIS AND REPAIR WORKFLOW  ........

22

Work Flow ................................................................

22

DTC/CIRCUIT DIAGNOSIS  .........................

25

INTERIOR ROOM LAMP POWER SUPPLY 
CIRCUIT ............................................................

25

Component Function Check  ....................................

25

Diagnosis Procedure  ...............................................

25

INTERIOR ROOM LAMP CONTROL CIRCUIT 

...

27

Component Function Check  ....................................

27

Diagnosis Procedure  ...............................................

27

Revision: 2012 October

2013 Murano CrossCabriolet

INL-2

TRUNK ROOM LAMP CIRCUIT  ........................

29

Diagnosis Procedure  ..............................................

29

STEP LAMP CIRCUIT  .......................................

30

Component Function Check  ...................................

30

Diagnosis Procedure  ..............................................

30

PUSH-BUTTON IGNITION SWITCH ILLUMI-
NATION CIRCUIT  ..............................................

32

Component Function Check  ...................................

32

Diagnosis Procedure  ..............................................

32

SYMPTOM DIAGNOSIS  .............................

34

INTERIOR LIGHTING SYSTEM SYMPTOMS ...

34

Symptom Table  ......................................................

34

REMOVAL AND INSTALLATION ...............

35

MAP LAMP  ........................................................

35

Exploded View  ........................................................

35

Removal and Installation  ........................................

35

Replacement ..........................................................

36

VANITY MIRROR LAMP  ...................................

37

Exploded View  ........................................................

37

Replacement ..........................................................

37

GLOVE BOX LAMP ...........................................

38

Exploded View  ........................................................

38

Replacement ...........................................................

38

CONSOLE POCKET LAMP  ..............................

39

Exploded View  ........................................................

39

Replacement ...........................................................

39

STEP LAMP .......................................................

40

Exploded View  ........................................................

40

Removal and Installation .........................................

40

Replacement ...........................................................

40

TRUNK ROOM LAMP  .......................................

42

Exploded View  ........................................................

42

Removal and Installation .........................................

42

Replacement ...........................................................

42

SERVICE DATA AND SPECIFICATIONS 
(SDS) ..........................................................

44

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

44

Bulb Specifications ..................................................

44

Revision: 2012 October

2013 Murano CrossCabriolet

PRECAUTIONS

INL-3

< PRECAUTION >

C

D

E

F

G

H

I

J

K

M

A

B

INL

N

O

P

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000008460357

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Battery Service

INFOID:0000000008460358

Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.

Service Procedure Precautions for Models with a Pop-up Roll Bar

INFOID:0000000008460359

WARNING:

Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll

over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.

• Before removing and installing the pop-up roll bar component parts and harness, always turn the

ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)

• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS

AIR BAG CONTROL warnings in the Service Manual.

Revision: 2012 October

2013 Murano CrossCabriolet

 

 

 

 

 

 

 

Content      ..     48      49      50      51     ..