Nissan Murano Z50 (2007 year). Manual - part 34

BODY REPAIR

BL-289

C

D

E

F

G

H

J

K

L

M

A

B

BL

Revision: 2006 July

2007 Murano

Replacement Operations

NIS001AJ

DESCRIPTION

This section is prepared for technicians who have attained a high level of skill and experience in repairing col-
lision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body
repair techniques should not attempt to repair collision-damaged vehicles by using this section.

Technicians are also encouraged to read Body Repair Manual (Fundamentals) in order to ensure that the orig-
inal functions and quality of the vehicle can be maintained. The Body Repair Manual (Fundamentals) contains
additional information, including cautions and warning, that are not including in this manual. Technicians
should refer to both manuals to ensure proper repairs.

Please note that these information are prepared for worldwide usage, and as such, certain procedures might
not apply in some regions or countries.

BL-290

BODY REPAIR

Revision: 2006 July

2007 Murano

The symbols used in this section for cutting and welding / brazing operations are shown below.

PIIA0149E

BODY REPAIR

BL-291

C

D

E

F

G

H

J

K

L

M

A

B

BL

Revision: 2006 July

2007 Murano

●

Front pillar butt joint can be determined anywhere within shaded
area as shown in the figure. The best location for the butt joint is
at position A due to the construction of the vehicle. Refer to the
front pillar section.

●

Determine cutting position and record distance from the locating
indent. Use this distance when cutting the service part. Cut outer
front pillar over 60 mm above inner front pillar cut position.

●

Prepare a cutting jig to make outer pillar easier to cut. Also, this
will permit service part to be accurately cut at joint position.

●

An example of cutting operation using a cutting jig is as follows.

1.

Mark cutting lines.
A: Cut position of outer pillar
B: Cut position of inner pillar

2.

Align cutting line with notch on jig. Clamp jig to pillar.

3.

Cut outer pillar along groove of jig. (At position A)

4.

Remove jig and cut remaining portions.

5.

Cut inner pillar at position B in same manner.

PIIA0150E

PIIA0151E

PIIA0152E

PIIA0153E

BL-292

BODY REPAIR

Revision: 2006 July

2007 Murano

HOODLEDGE

Change parts

●

Hoodledge assembly (LH)

●

Hoodledge reinforcement (LH)

SIIA2180E

BODY REPAIR

BL-293

C

D

E

F

G

H

J

K

L

M

A

B

BL

Revision: 2006 July

2007 Murano

HOODLEDGE (PARTIAL REPLACEMENT)

Change parts

●

Upper hoodledge (RH)

●

Lower front hoodledge (RH)

●

Hoodledge reinforcement (RH)

SIIA2181E

BL-294

BODY REPAIR

Revision: 2006 July

2007 Murano

FRONT SIDE MEMBER

●

Work after hoodledge has been removed.

SIIA2182E

BODY REPAIR

BL-295

C

D

E

F

G

H

J

K

L

M

A

B

BL

Revision: 2006 July

2007 Murano

Change parts

●

Front side member (LH)

●

Front side member closing plate assembly (LH)

BL-296

BODY REPAIR

Revision: 2006 July

2007 Murano

FRONT SIDE MEMBER (PARTIAL REPLACEMENT)

Change parts

●

Front side member (RH)

●

Front side member front closing plate (RH)

SIIA2183E

BODY REPAIR

BL-297

C

D

E

F

G

H

J

K

L

M

A

B

BL

Revision: 2006 July

2007 Murano

FRONT PILLAR

●

Work after hoodledge reinforcement has been removed.

SIIA2184E

BL-298

BODY REPAIR

Revision: 2006 July

2007 Murano

Change parts

●

Side body assembly (LH)

●

Inner side roof rail (LH)

●

Side dash (LH)

SIIA2185E

BODY REPAIR

BL-299

C

D

E

F

G

H

J

K

L

M

A

B

BL

Revision: 2006 July

2007 Murano

CENTER PILLAR

Change parts

●

Side body assembly (LH)

●

Inner center pillar (LH)

SIIA2186E

BL-300

BODY REPAIR

Revision: 2006 July

2007 Murano

SIIA2187E

BODY REPAIR

BL-301

C

D

E

F

G

H

J

K

L

M

A

B

BL

Revision: 2006 July

2007 Murano

OUTER SILL

Change parts

SIIA2188E

BL-302

BODY REPAIR

Revision: 2006 July

2007 Murano

●

Outer sill (LH)

●

Outer sill reinforcement assembly (LH)

●

Lower front pillar reinforcement (LH)

●

Rear outer sill reinforcement (LH)

SIIA2189E

BODY REPAIR

BL-303

C

D

E

F

G

H

J

K

L

M

A

B

BL

Revision: 2006 July

2007 Murano

REAR FENDER

Change parts

●

Rear fender assembly (LH)

SIIA2190E

BL-304

BODY REPAIR

Revision: 2006 July

2007 Murano

SIIA2191E