Content .. 12 13 14 15 ..

Nissan Murano Z50 (2007 year). Manual - part 14

NAVIGATION SYSTEM

AV-185

Revision: 2006 July

2007 Murano

15.

CHECK CAMERA-CONNECTION RECOGNITION SIGNAL

Connect rear view camera control unit and display control unit connectors.

Turn ignition switch ON.

Check voltage between rear view camera control unit harness
connector B37 terminal 5 and ground.

OK or NG

>> Replace display control unit.

>> Replace rear view camera control unit.

5 – Ground

: Approx. 0 V

SKIB7849E

AV-186

NAVIGATION SYSTEM

Revision: 2006 July

2007 Murano

Status Screen for Audio and A/C Is Not Displayed When Showing Map Screen

NKS0024M

Symptom: Status screen is not displayed in the lower portion of map screen when operating audio system and
A/C system.

CHECK HARNESS

Turn ignition switch OFF.

Disconnect display control unit and display connectors.

Check continuity between display control unit harness connector
(A) M43 terminals 53, 55 and display harness connector (B)
M38 terminals 20, 8.

Check continuity between display control unit harness connector
(A) M43 terminals 53, 55 and ground.

OK or NG

>> GO TO 2.

>> Repair harness or connector.

CHECK VERTICAL SYNCHRONIZING (VP) SIGNAL

Connect display control unit and display connectors.

Turn ignition switch ON.

Check voltage waveform between display control unit harness
connector M43 terminal 53 and ground with CONSULT-ll or
oscilloscope.

OK or NG

>> GO TO 3.

>> Replace display.

CHECK HORIZONTAL SYNCHRONIZING (HP) SIGNAL

Check voltage waveform between display control unit harness con-
nector M43 terminal 55 and ground with CONSULT-ll or oscillo-
scope.

OK or NG

>> Replace display control unit.

>> Replace display.

53 – 20

: Continuity should exist.

55 – 8

: Continuity should exist.

53, 55 – Ground

: Continuity should not exist.

SKIB7850E

53 – Ground:

SKIB7851E

SKIB3598E

55 – Ground:

SKIB7852E

SKIB3601E

NAVIGATION SYSTEM

AV-187

Revision: 2006 July

2007 Murano

Vehicle Mark Is Not Displayed Properly

NKS002QD

Symptom: Vehicle mark is not displayed at the vehicle driving position properly.

NAVIGATION SYSTEM ADJUSTMENT

Select “Navigation” in Confirmation/Adjustment mode, and adjust items, “Steering Angle Adjustment” and
“Speed Calibration”. Refer to

AV-167, "Navigation"

Check symptom with driving.

Is any malfunction observed?

YES

>> GO TO 2.

>> INSPECTION END

SELF-DIAGNOSIS OF NAVI

Start self-diagnosis of NAVI, and check any malfunction related to GPS. Refer to

AV-161, "Self-Diagnosis

Mode (NAVI)"

Is any malfunction related to GPS observed?

YES

>> Repair malfunctioning part.

>> GO TO 3.

CHECK VEHICLE SIGNAL

Select “Vehicle Signals” in Confirmation/Adjustment mode, and check the vehicle speed signal and reverse
signal inputting to NAVI control unit. Refer to

AV-167, "Vehicle Signals"

OK or NG

>> Limit of position detection capacity.

●

Check NAVI control unit vehicle speed signal circuit, and repair malfunctioning part.

●

Check NAVI control unit reverse signal circuit, and repair malfunctioning part.

AV-188

NAVIGATION SYSTEM

Revision: 2006 July

2007 Murano

Tint Is Strange for The RGB Image

NKS0024H

Symptom: Tint of all RGB images is strange.

CHECK HARNESS

Turn ignition switch OFF.

Disconnect display control unit and display connectors.

Check the malfunctioning circuit according to the symptoms.

●

Light blue (Cyan) tinged screen
Check continuity between display control unit harness connector
(A) M43 terminal 50 and display harness connector (B) M38 ter-
minal 17.

Check continuity between display control unit harness connector
(A) M43 terminal 50 and ground.

●

Purple (Magenta) tinged screen
Check continuity between display control unit harness connector
(A) M43 terminal 52 and display harness connector (B) M38 ter-
minal 6.

Check continuity between display control unit harness connector
(A) M43 terminal 52 and ground.

●

Yellow tinged screen
Check continuity between display control unit harness connector
(A) M43 terminal 54 and display harness connector (B) M38 ter-
minal 18.

Check continuity between display control unit harness connector
(A) M43 terminal 54 and ground.

OK or NG

>> GO TO 2.

>> Repair harness or connector.

50 – 17

: Continuity should exist.

50 – Ground

: Continuity should not exist.

SKIB7853E

52 – 6

: Continuity should exist.

52 – Ground

: Continuity should not exist.

SKIB7854E

54 – 18

: Continuity should exist.

54 – Ground

: Continuity should not exist.

SKIB7855E

NAVIGATION SYSTEM

AV-189

Revision: 2006 July

2007 Murano

CHECK RGB SIGNAL

Connect display control unit and display connectors.

Turn ignition switch ON.

Start Confirmation/Adjustment mode. Refer to

AV-164, "Confirmation/Adjustment Mode"

Display color bar by selecting “Display Color Spectrum Bar” on Display Diagnosis screen. Refer to

AV-

165, "DISPLAY DIAGNOSIS"

Check the malfunctioning circuit according to the symptoms.

●

Light blue (Cyan) tinged screen
Check voltage waveform between display control unit harness
connector M43 terminal 50 and ground with CONSULT-ll or
oscilloscope.

●

Purple (Magenta) tinged screen
Check voltage waveform between display control unit harness
connector M43 terminal 52 and ground with CONSULT-ll or
oscilloscope.

●

Yellow tinged screen
Check voltage waveform between display control unit harness
connector M43 terminal 54 and ground with CONSULT-ll or
oscilloscope.

OK or NG

>> Replace display.

>> Replace display control unit.

50 – Ground:

SKIB7856E

SKIB7769E

52 – Ground:

SKIB7857E

SKIB7770E

54 – Ground:

SKIB7858E

SKIB7771E

AV-190

NAVIGATION SYSTEM

Revision: 2006 July

2007 Murano

Tint Is Strange for The RGB Image (Only NAVI Screen)

NKS0024I

Symptom: Tint of map screen is strange. (Status screen for audio and A/C, TRIP screen and FUEL ECON-
OMY screen are normal.)

CHECK HARNESS

Turn ignition switch OFF.

Disconnect NAVI control unit and display unit connectors.

Check the malfunctioning circuit according to the symptoms.

●

Light blue (Cyan) tinged screen
Check continuity between NAVI control unit harness connector
(A) M63 terminal 44 and display control unit harness connector
(B) M43 terminal 44.

Check continuity between NAVI control unit harness connector
(A) M63 terminal 44 and ground.

●

Purple (Magenta) tinged screen
Check continuity between NAVI control unit harness connector
(A) M63 terminal 45 and display control unit harness connector
(B) M43 terminal 46.

Check continuity between NAVI control unit harness connector
(A) M63 terminal 45 and ground.

●

Yellow tinged screen
Check continuity between NAVI control unit harness connector
(A) M63 terminal 46 and display control unit harness connector
(B) M43 terminal 48.

Check continuity between NAVI control unit harness connector
(A) M63 terminal 46 and ground.

OK or NG

>> GO TO 2.

>> Repair harness or connector.

44 – 44

: Continuity should exist.

44 – Ground

: Continuity should not exist.

SKIB7859E

45 – 46

: Continuity should exist.

45 – Ground

: Continuity should not exist.

SKIB7860E

46 – 48

: Continuity should exist.

46 – Ground

: Continuity should not exist.

SKIB7861E

NAVIGATION SYSTEM

AV-191

Revision: 2006 July

2007 Murano

CHECK RGB SIGNAL

Connect NAVI control unit and display control unit connectors.

Turn ignition switch ON.

Start Confirmation/Adjustment (Navigation) mode. Refer to

AV-164, "Confirmation/Adjustment Mode"

Display color bar by selecting “Color Spectrum bar” on Display Diagnosis screen. Refer to

AV-166, "Dis-

play Diagnosis"

Check the malfunctioning circuit according to the symptoms.

●

Light blue (Cyan) tinged screen
Check voltage waveform between NAVI control unit harness
connector M63 terminal 44 and ground with CONSULT-II or
oscilloscope.

●

Purple (Magenta) tinged screen
Check voltage waveform between NAVI control unit harness
connector M63 terminal 45 and ground with CONSULT-II or
oscilloscope.

●

Yellow tinged screen
Check voltage waveform between NAVI control unit harness
connector M63 terminal 46 and ground with CONSULT-II or
oscilloscope.

OK or NG

>> Replace display control unit.

>> Replace NAVI control unit.

44 – Ground:

SKIB6997E

SKIB7360E

45 – Ground:

SKIB6998E

SKIB7361E

46 – Ground:

SKIB6999E

SKIB7362E

AV-192

NAVIGATION SYSTEM

Revision: 2006 July

2007 Murano

RGB Image Is Rolling

NKS0024J

Symptom: Map screen is rolling.

CHECK HARNESS

Turn ignition switch OFF.

Disconnect NAVI control unit and display control unit connectors.

Check continuity between NAVI control unit harness connector
(A) M63 terminal 48 and display control unit harness connector
(B) M43 terminal 43.

Check continuity between NAVI control unit harness connector
(A) M63 terminal 48 and ground.

OK or NG

>> GO TO 2.

>> Repair harness or connector.

CHECK RGB SYNCHRONIZING SIGNAL

Connect NAVI control unit and display control unit connectors.

Turn ignition switch ON.

When displaying RGB image, check voltage waveform between
NAVI control unit harness connector M63 terminal 48 and
ground with CONSULT-ll or oscilloscope.

OK or NG

>> GO TO 3.

>> Replace NAVI control unit.

CHECK HARNESS

Turn ignition switch OFF.

Disconnect display control unit and display connectors.

Check continuity between display control unit harness connector
(A) M43 terminal 56 and display harness connector (B) M38 ter-
minal 19.

Check continuity between display control unit harness connector
(A) M43 terminal 56 and ground.

OK or NG

>> GO TO 4.

>> Repair harness or connector.

48 – 43

: Continuity should exist.

48 – Ground

: Continuity should not exist.

SKIB7862E

48 – Ground:

SKIB7001E

SKIB3603E

56 – 19

: Continuity should exist.

56 – Ground

: Continuity should not exist.

SKIB7863E

NAVIGATION SYSTEM

AV-193

Revision: 2006 July

2007 Murano

CHECK RGB SYNCHRONIZING SIGNAL

Connect display control unit and display connectors.

Turn ignition switch ON.

When displaying RGB image, check voltage waveform between
display control unit harness connector M43 terminal 56 and
ground with CONSULT-ll or oscilloscope.

OK or NG

>> Replace display.

>> Replace display control unit.

Values for All Items in The TRIP Screen Do Not Change

NKS0024N

Symptom: Values for items, “Elapsed Time”, “Driving Distance” and “Average Speed” in the TRIP screen do
not change. FUEL ECONOMY screen is not displayed when pressing “TRIP” button.

CHECK DISPLAY CONTROL UNIT IGNITION SIGNAL

Select “Vehicle Signals” in Confirmation/Adjustment mode, and check the ignition signal inputting to display
control unit. Refer to

AV-165, "VEHICLE SIGNALS"

OK or NG

>> Replace display control unit.

>> Check display control unit ignition signal circuit, and repair malfunctioning part.

Values for Items, “Driving Distance” and “Average Speed” Do Not Change

NKS0024O

Symptom: Values for Items, "Driving Distance" and "Average Speed" do not change. (The Value for "Elapsed
Time" Changes.)

CHECK DISPLAY CONTROL UNIT VEHICLE SPEED SIGNAL

Select “Vehicle Signals” in Confirmation/Adjustment mode, and check the vehicle speed signal inputting to dis-
play control unit. Refer to

AV-165, "VEHICLE SIGNALS"

OK or NG

>> Replace display control unit.

>> Check display control unit vehicle speed signal circuit, and repair malfunctioning part.

Values for All Items in The FUEL ECONOMY Screen Do Not Change

NKS0024P

Symptom: Values for items, “Average Fuel Economy” and “Distance to Empty” in the FUEL ECONOMY screen
do not change.

CHECK CONDITION

Check if values for all items in the TRIP screen change properly.
OK or NG

>> GO TO 2.

>> Repair malfunctioning part. Refer to

AV-193, "Values for All Items in The TRIP Screen Do Not

Change"

AV-193, "Values for Items, “Driving Distance” and “Average Speed” Do Not Change"

56 – Ground:

SKIB7864E

SKIB3603E

AV-194

NAVIGATION SYSTEM

Revision: 2006 July

2007 Murano

CHECK CAN COMMUNICATION

Check CAN communication. Refer to

AV-176, "CAN Communication Check"

OK or NG

>> Replace display control unit.

>> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO

LAN-3, "Precautions When

Using CONSULT-II"

Voice Guidance Is Not Heard

NKS0024K

Symptom: Voice guidance does not sound at route guidance.

CHECK HARNESS

Turn ignition switch OFF.

Disconnect NAVI control unit and audio unit connectors.

Check continuity between NAVI control unit harness connector
(A) M62 terminals 12, 14 and audio unit harness connector (B)
M46 terminals 36, 34.

Check continuity between NAVI control unit harness connector
(A) M62 terminals 12, 14 and ground.

OK or NG

>> GO TO 2.

>> Repair harness or connector.

CHECK VOICE GUIDANCE SIGNAL

Connect NAVI control unit and audio unit connectors.

Turn ignition switch ON.

Check voltage waveform between NAVI control unit harness
connector M62 terminals 12 and 14 with CONSULT-ll or oscillo-
scope.

OK or NG

>> Replace audio unit.

>> Replace NAVI control unit.

12 – 36

: Continuity should exist.

14 – 34

: Continuity should exist.

12, 14 – Ground

: Continuity should not exist.

SKIB7865E

12 – 14:

SKIB7003E

SKIB3609E

NAVIGATION SYSTEM

AV-195

Revision: 2006 July

2007 Murano

Example of Symptoms Possible No Malfunction

NKS0024Z

For Navigation System operation information, refer to Navigation System Owner's Manual.

BASIC OPERATIONS

NOTE:
Locations stored in the Address Book and other memory functions may be lost if the vehicle's battery is disconnected or is discharged. If
this occurs, service the vehicle's battery as necessary and re-enter the information in the Address Book.

VEHICLE MARKS

Symptom

Possible cause

Possible solution

No image is displayed.

The brightness is at the lowest setting.

Adjust the brightness of the display.

The display is turned off.

Press and hold the

button to turn on the

display.

No voice guidance is available. or
The volume is too high or too low.

The volume is not set correctly, or it is turned
off.

Adjust the volume of voice guidance.

No map is displayed on the
screen.

The DVD-ROM is not inserted, or it is inserted
upside down.

Insert the DVD-ROM correctly.

A screen other than map screen is displayed.

Press the “MAP” button.

The pickup lens of the DVD unit is dirty.

The pickup lens can become dirty depending
on the usage of the vehicle. Contact a NISSAN
dealer or qualified workshop for pickup lens
cleaning.

The screen is too dim. The move-
ment is slow.

The temperature in the interior of the vehicle is
low.

Wait until the interior of the vehicle has
warmed up.

Some pixels in the display are
darker or brighter than others.

This condition is an inherent characteristic of
liquid crystal displays.

This is not a malfunction.

Some menu items cannot be
selected.

Some menu items become unavailable while
the vehicle is driven.

Park the vehicle in a safe location, then oper-
ate the navigation system.

Symptom

Possible cause

Possible solution

Names of roads and locations dif-
fer between plan view and BIRD-

VIEW

™

This is because the quantity of the displayed
information is reduced so that the screen does
not become difficult to read. There is also a
chance that names of the roads or locations
may be displayed several times, and the names
appearing on the screen may be different
because of a processing procedure.

This is not a malfunction.

The vehicle mark is not displayed
in the correct position.

The vehicle was transported after the ignition
switch was turned off, for example, by a ferry or
car transporter.

Drive the vehicle for a while on a road where
GPS signals can be received.

The position and direction of the vehicle mark
may be incorrect depending on the driving envi-
ronments and the levels of positioning accuracy
of the navigation system.

This is not a malfunction. Drive the vehicle for
a while to automatically correct the position
and direction of the vehicle mark.

When the vehicle is travelling on a
new road, the vehicle mark is
located on another road nearby.

The system automatically places the vehicle
mark on the nearest available road, because
the new road is not stored in the map data.

Updated road information will be included in
the next version of the DVD-ROM.

The screen does not switch to the
night screen even after turning on
the headlights.

The daytime screen was set the last time the
headlights were turned on.

Set the screen to the night screen mode using

button when turning on the headlights.

The map does not scroll even
when the vehicle is moving.

The current location map screen is not dis-
played.

Press the “MAP” button.

The vehicle mark is not displayed.

The current location map screen is not dis-
played.

Press the “MAP” button.

AV-196

NAVIGATION SYSTEM

Revision: 2006 July

2007 Murano

DVD-ROM

ROUTE CALCULATION AND VISUAL GUIDANCE

The GPS indicator on the screen
remains gray.

GPS signals cannot be received depending on
the vehicle location, such as in a parking
garage, on a road that has numerous tall build-
ings, etc.

Drive on an open, straight road for a while.

A sufficient amount of GPS satellites is not
available.

Please wait for the satellites to move to loca-
tions available for the navigation system.

The location of the vehicle mark is
misaligned from the actual posi-
tion.

When using tire chains or replacing the tires,
speed calculations based on the speed sensor
may be incorrect.

Drive the vehicle for a while [at approximately
30 km/h (19 MPH) for about 30 minutes] to
automatically correct the vehicle's mark posi-
tion. If this does not correct the vehicle mark
position, contact a NISSAN dealer or qualified
workshop.

The map data has a mistake or is incomplete
(the vehicle mark position is always misaligned
in the same area).

Updated road information will be included in
the next version of the DVD-ROM.

Symptom

Possible cause

Possible solution

Symptom

Possible cause

Possible solution

The message “Error” appears.

The DVD-ROM is dirty or partially damaged.

Check the DVD-ROM and wipe it clean with a
soft cloth.

If any damage, replace the DVD-ROM.

Symptom

Possible cause

Possible solution

In the auto re-route calculation,
waypoints are not included.

Waypoints that you have already passed are
not included in the auto re-route calculation.

To go to that waypoint again, it is necessary to
edit the route.

Route information is not dis-
played.

Route calculation has not yet been performed.

Set the destination and perform route calcula-
tion.

Vehicle is not driving on the suggested route.

Drive on the suggested route.

Route guidance is set to off.

Turn on the route guidance.

The auto re-route calculation (or
detour calculation) suggests the
same route as the one previously
suggested.

Route calculations took priority conditions into
consideration, but the same route was calcu-
lated.

This is not a malfunction.

A waypoint cannot be added.

Five waypoints are already set on the route,
including the ones that you have already
passed.

A maximum of 5 waypoints can be set on the
route. If you want to go to 6 or more waypoints,
perform route calculations several times, as
necessary.

The suggested route is not dis-
played.

Roads near the destination cannot be calcu-
lated.

Reset the destination to a main or ordinary
road, and recalculate the route.

The starting point and destination are too close.

Set a more distant destination.

The starting point and destination are too far
away.

Divide your trip by selecting one or two inter-
mediate destinations, and perform a global
route calculation based on multiple route cal-
culations.

There are time restricted roads (day of week,
time) near the current vehicle location or desti-
nation.

Set [Use Time Restricted Roads] to off.

The part of the route already
passed is deleted.

A route is managed by sections between way-
points. If passing the first waypoint, the section
between the starting point and the waypoint is
deleted. (It may not be deleted depending on
the area.)

This is not a malfunction.

NAVIGATION SYSTEM

AV-197

Revision: 2006 July

2007 Murano

VOICE GUIDANCE

REAR VIEW MONITOR

An indirect route is suggested.

If there are restrictions (such as one-way
streets) on roads close to the starting point or
destination, the system may suggest an indirect
route.

Adjust the location of the starting point or desti-
nation.

The system may suggest an indirect route
because route calculation does not take into
consideration some areas such as narrow
streets (grey roads).

Reset the destination to a main or ordinary
road, and recalculate the route.

The landmark information does
not correspond to the actual infor-
mation.

This may be caused by insufficient or incorrect
data on the DVD-ROM.

Updated information will be included in the
next version of the DVD-ROM.

The suggested route does not
exactly connect with the starting
point, waypoints, or destination.

There is no data for route calculation closer to
these locations.

Set the starting point, waypoints and destina-
tion on a main road, and perform route calcula-
tion.

Symptom

Possible cause

Possible solution

Symptom

Possible cause

Possible solution

Voice guidance is not available.

Voice guidance is only available at certain inter-

sections marked with

. In some cases, voice

guidance is not available even when the vehicle
should make a turn.

This is not malfunction.

The vehicle has deviated from the suggested
route.

Go back to the suggested route or request
route calculation again.

Voice guidance is set to off.

Turn on the voice guidance.

Route guidance is set to off.

Turn on the route guidance.

The guidance content does not
correspond to the actual condition.

The content of voice guidance may vary,
depending on the types of intersections where
turns are made.

Follow all traffic rules and regulations.

Symptom

Possible cause

Possible solution

Rear view monitor image is not
shown.

Selector lever is not set to R position.

Shift the selector lever to R position.

Rear view monitor image is fuzzy.

The front glass of the camera lens is dirty.

Wipe it with a soft wet cloth lightly.

Adherence of raindrops or snow.

Wipe it with a soft cloth lightly.

The lens is illuminated directly by sunlight or light
from headlight of cars behind.

The fuzzy image recovers when the light is
covered.

AV-198

NAVIGATION SYSTEM

Revision: 2006 July

2007 Murano

Removal and Installation of NAVI Control Unit

NKS00251

REMOVAL

Remove center console. Refer to

IP-17, "CENTER CONSOLE ASSEMBLY"

Remove console cover (LH and RH). Refer to

IP-17, "CENTER CONSOLE ASSEMBLY"

Remove control device assembly, and remove screws (2) and
nut.

Disconnect NAVI control unit connector.

Pull NAVI control unit up-ward, then vehicle rear side.

CAUTION:

Cover unit with cloth avoid contact with console box
bracket that may cause scratches or damages.

Remove screws (4), and remove brackets.

INSTALLATION

Installation is the reverse order of removal.

PKIA2465E

PKIA2466E

PKIA2467E

NAVIGATION SYSTEM

AV-199

Revision: 2006 July

2007 Murano

Removal and Installation of GPS Antenna

NKS00252

REMOVAL

Remove cluster lid C. Refer to

IP-10, "INSTRUMENT PANEL ASSEMBLY"

Remove center console. Refer to

IP-17, "CENTER CONSOLE ASSEMBLY"

Remove console cover (LH). Refer to

IP-17, "CENTER CONSOLE ASSEMBLY"

Remove display. Refer to

AV-200, "Removal and Installation of Display"

Disengaged the clips (4) to separate antenna feeder.

Remove screw, and remove GPS antenna.

INSTALLATION

Installation is the reverse order of removal.

Removal and Installation of A/C and AV Switch

NKS00254

Refer to

AV-61, "Removal and Installation for A/C and AV Switch"

Removal and Installation of Audio Steering Switch

NKS00253

Refer to

AV-62, "Removal and Installation of Audio Steering Switch"

PKIA2468E

PKIA2469E

AV-200

NAVIGATION SYSTEM

Revision: 2006 July

2007 Murano

Removal and Installation of Display

NKS00255

REMOVAL

Remove center ventilator. Refer to

IP-10, "INSTRUMENT PANEL ASSEMBLY"

Remove screws (4), and remove display.

Remove screws (4), and remove brackets.

INSTALLATION

Installation is the reverse order of removal.

PKIA2473E

PKIA2474E

Content .. 12 13 14 15 ..