Nissan Murano Z50 (2006 year). Manual - part 184

SUNROOF

RF-27

C

D

E

F

G

H

J

K

L

M

A

B

RF

Revision: 2006 August

2006 Murano

Check Sunroof Switch Circuit 5

NIS001DD

1. 

CHECK SUNROOF SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sunroof switch connector.

3.

Check continuity between sunroof switch terminals 1, 3 and 6.

OK or NG

OK

>> GO TO 2.

NG

>> Replace sunroof switch.

2. 

CHECK SUNROOF SWITCH OUTPUT SIGNAL

1.

Connect sunroof switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between sunroof motor assembly connector and
ground.

OK or NG

OK

>> Replace sunroof motor assembly.

NG

>> Check the condition of the harness and the connector.

Check Sunroof Switch Circuit 6

NIS001DE

1. 

CHECK SUNROOF SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sunroof switch connector.

3.

Check continuity between sunroof switch terminals 3 and 6.

OK or NG

OK

>> GO TO 2.

NG

>> Replace sunroof switch.

Terminals

Condition

Continuity 

1
3

6

Slide switch
FULL CLOSE position

Yes

Other than above

No

PIIA4523E

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(–)

R6

2 (G)

4 (Y)

Ground

Slide switch
SLIDE POSITION 4 

0

Other than above 

Battery voltage

PIIA4521E

Terminals

Condition

Continuity 

3

6

Slide switch
FULL OPEN position

Yes

Other than above

No

PIIA4526E

RF-28

SUNROOF

Revision: 2006 August

2006 Murano

2. 

CHECK SUNROOF SWITCH OUTPUT SIGNAL

1.

Connect sunroof switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between sunroof motor assembly connector and
ground.

OK or NG

OK

>> Replace sunroof motor assembly.

NG

>> Check the condition of the harness and the connector.

Check Sunroof Switch Circuit 7

NIS001DF

1. 

CHECK SUNROOF SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sunroof switch connector.

3.

Check continuity between sunroof switch terminals 5 and 6.

OK or NG

OK

>> GO TO 2.

NG

>> Replace sunroof switch.

2. 

CHECK SUNROOF SWITCH OUTPUT SIGNAL

1.

Connect sunroof switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between sunroof motor assembly connector and
ground.

OK or NG

OK

>> Replace sunroof motor assembly.

NG

>> Check the condition of the harness and the connector.

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(–)

R6

4 (Y)

Ground

Slide switch
FULL OPEN position 

0

Other than above 

Battery voltage

PIIB0505E

Terminals

Condition

Continuity 

5

6

Tilt switch
UP position

Yes

Other than above

No

PIIA4529E

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(–)

R6

1 (V)

Ground

Tilt switch
UP position 

0

Other than above 

Battery voltage

PIIA4527E

SUNROOF

RF-29

C

D

E

F

G

H

J

K

L

M

A

B

RF

Revision: 2006 August

2006 Murano

Check Sunroof Switch Circuit 8

NIS001DG

1. 

CHECK SUNROOF SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sunroof switch connector.

3.

Check continuity between sunroof switch terminals 4 and 6.

OK or NG

OK

>> GO TO 2.

NG

>> Replace sunroof switch.

2. 

CHECK SUNROOF SWITCH OUTPUT SIGNAL

1.

Connect sunroof switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between sunroof motor assembly connector and
ground.

OK or NG

OK

>> Replace sunroof motor assembly.

NG

>> Check the condition of the harness and the connector.

Check Sunroof Switch Circuit 9

NIS001DH

1. 

CHECK SUNROOF MOTOR OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sunroof motor switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between sunroof motor assembly connector R6
terminals 1, 2, 3, 4, 5 and ground.

OK or NG

OK

>> GO TO 2

NG

>> Replace sunroof motor assembly.

Terminals

Condition

Continuity 

4

6

Tilt switch
UP position

Yes

Other than above

No

PIIA4532E

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(–)

R6

5 (O)

Ground

Tilt switch
DOWN position 

0

Other than above 

Battery voltage

PIIA4530E

1 (V) – Ground

: Battery voltage

2 (G) – Ground

: Battery voltage

3 (R) – Ground

: Battery voltage

4 (Y) – Ground

: Battery voltage

5 (O) – Ground

: Battery voltage

PIIA4536E

RF-30

SUNROOF

Revision: 2006 August

2006 Murano

2. 

CHECK HARNESS CONTINUITY 

1.

Turn ignition switch OFF.

2.

Disconnect sunroof switch connector.

3.

Check continuity between sunroof motor assembly connector
R6 terminals 1, 2, 3, 4, 5 and sunroof switch connector R5 termi-
nals 1, 2, 3, 4, 5.

4.

Check continuity between sunroof motor assembly connector
R6 terminals 1, 2, 3, 4, 5 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness.

3. 

CHECK GROUND CIRCUIT

Check continuity between sunroof switch connector R5 terminal 6
and ground.

OK or NG

OK

>> Check condition of the harness and the connector.

NG

>> Repair or replace harness.

1 (V) – 5 (V)

: Continuity should exist.

2 (G) – 1 (G)

: Continuity should exist.

3 (R) – 2 (R)

: Continuity should exist.

4 (Y) – 3 (Y)

: Continuity should exist.

5 (O) – 4 (O)

: Continuity should exist.

1 (V) – Ground

: Continuity should not exist.

2 (G) – Ground

: Continuity should not exist.

3 (R) – Ground

: Continuity should not exist.

4 (Y) – Ground

: Continuity should not exist.

5 (O) – Ground

: Continuity should not exist.

PIIA4537E

6 (B) – Ground

: Continuity should exist.

PIIA4538E

SUNROOF

RF-31

C

D

E

F

G

H

J

K

L

M

A

B

RF

Revision: 2006 August

2006 Murano

Check Sunroof Switch Circuit 10

NIS001DI

1. 

CHECK SUNROOF SWITCH OUTPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between sunroof motor assembly connector and
ground.

OK or NG

OK

>> Replace sunroof motor assembly.

NG

>> GO TO 2.

2. 

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect sunroof motor assembly and sunroof switch connector.

3.

Check continuity between sunroof motor assembly connector R6 terminal 2 and sunroof switch connector
R5 terminal 1.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness between sunroof motor

assembly and sunroof switch.

3. 

CHECK SUNROOF SWITCH

Check continuity between sunroof switch terminals 1 and 6.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace sunroof switch.

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(–)

R6

2 (G)

Ground

Slide switch
SLIDE POSITION 2
SLIDE POSITION 3
SLIDE POSITION 4

0

Other than above 

Battery voltage

PIIA4518E

2 (G) – 1 (G)

: Continuity should exist.

PIIA4519E

Terminals

Condition

Continuity 

1

6

Slide switch
SLIDE POSITION 2
SLIDE POSITION 3
SLIDE POSITION 4

Yes

Other than above

No

PIIA4520E

RF-32

SUNROOF

Revision: 2006 August

2006 Murano

Check Sunroof Switch Circuit 11

NIS001DJ

1. 

CHECK SUNROOF SWITCH OUTPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between sunroof motor assembly connector and
ground.

OK or NG

OK

>> Replace sunroof motor assembly.

NG

>> GO TO 2.

2. 

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect sunroof motor assembly and sunroof switch connector.

3.

Check continuity between sunroof motor assembly connector R6 terminal 3 and sunroof switch connector
R5 terminal 2.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness between sunroof motor

assembly and sunroof switch.

3. 

CHECK SUNROOF SWITCH

Check continuity between sunroof switch terminals 2 and 6.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace sunroof switch.

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(–)

R6

3 (R)

Ground

Slide switch
FULL CLOSE
SLIDE POSITION 1
SLIDE POSITION 2

0

Other than above 

Battery voltage

PIIA4512E

3 (R) – 2 (R)

: Continuity should exist.

PIIA4513E

Terminals

Condition

Continuity 

2

6

Slide switch
FULL CLOSE
SLIDE POSITION 1
SLIDE POSITION 2

Yes

Other than above

No

PIIA4514E

SUNROOF

RF-33

C

D

E

F

G

H

J

K

L

M

A

B

RF

Revision: 2006 August

2006 Murano

Check Sunroof Switch Circuit 12

NIS001DK

1. 

CHECK SUNROOF SWITCH OUTPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between sunroof motor assembly connector and
ground.

OK or NG

OK

>> Replace sunroof motor assembly.

NG

>> GO TO 2.

2. 

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect sunroof motor assembly and sunroof switch connector.

3.

Check continuity between sunroof motor assembly connector R6 terminal 4 and sunroof switch connector
R5 terminal 3.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness between sunroof motor

assembly and sunroof switch.

3. 

CHECK SUNROOF SWITCH

Check continuity between sunroof switch terminals 3 and 6.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace sunroof switch.

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(–)

R6

4 (Y)

Ground

Slide switch
FULL CLOSE
FULL OPEN
SLIDE POSITION 4

0

Other than above 

Battery voltage

PIIB0505E

4 (Y) – 3 (Y)

: Continuity should exist.

PIIA4525E

Terminals

Condition

Continuity 

3

6

Slide switch
FULL CLOSE
FULL OPEN
SLIDE POSITION 4

Yes

Other than above

No

PIIA4526E

RF-34

SUNROOF

Revision: 2006 August

2006 Murano

Check Door Switch (With Intelligent Key) 

NIS001DL

1. 

CHECK DOOR SWITCH INPUT SIGNAL 

 With CONSULT-II

Check door switches (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA MONITOR” mode with CONSULT-II.

Without CONSULT-II

Check voltage between BCM connector and ground.

OK or NG

OK

>> Door switch is OK. 

NG

>> GO TO 2.

Monitor item

Condition

DOOR SW-DR

OPEN

: ON

CLOSE

: OFF

DOOR SW-AS

OPEN

: ON

CLOSE

: OFF

PIIA2464E

Item

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

Passenger 

side

M34

12 (R/G)

Ground

OPEN

0

CLOSE

Battery voltage

Driver

side

M36

62 (SB)

OPEN

0

CLOSE

Battery voltage

PIIA6158E

SUNROOF

RF-35

C

D

E

F

G

H

J

K

L

M

A

B

RF

Revision: 2006 August

2006 Murano

2. 

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect BCM and front door lock assembly (driver side and passenger side) connector.

3.

Check continuity between BCM connector M34, 36 terminals 12, 62 and front door lock assembly connec-
tor D10 (driver side), D38 (passenger side) terminal 4.

4.

Check continuity between BCM connector M34, 36 terminals 12,
62 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness between BCM and front door

lock assembly.

3. 

CHECK DOOR SWITCH

Check continuity between front door lock assembly terminal 4 and 5.

OK or NG

OK

>> GO TO 4. 

NG

>> Replace malfunction front door lock assembly.

Driver side

62 (SB) – 4 (SB)

: Continuity should exist.

Passenger side

12 (R/G) – 4 (R/G)

: Continuity should exist.

12 (R/G) – Ground

: Continuity should not exist.

62 (SB) – Ground

: Continuity should not exist.

PIIB0907E

Terminal

Door switch

Continuity

4

5

OPEN

No

CLOSE

Yes

PIIA4220E

RF-36

SUNROOF

Revision: 2006 August

2006 Murano

4. 

CHECK DOOR SWITCH GROUND CIRCUIT

1.

Check continuity between front door lock assembly connector D10 (driver side), D38 (passenger side) ter-
minal 5 and ground.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Repair or replace harness between front door lock

assembly and ground.

Check Door Switch (Without Intelligent Key)

NIS001DM

1. 

CHECK DOOR SWITCH INPUT SIGNAL 

 With CONSULT-II

Check door switches (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA MONITOR” mode with CONSULT-II.

Without CONSULT-II

Check voltage between BCM connector and ground.

OK or NG

OK

>> Door switch is OK. 

NG

>> GO TO 2.

5 (B) - Ground

: Continuity should exist.

PIIA9680E

Monitor item

Condition

DOOR SW-DR

OPEN

: ON

CLOSE

: OFF

DOOR SW-AS

OPEN

: ON

CLOSE

: OFF

PIIA2464E

Item

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

Passenger 

side

M34

12 (R)

Ground

OPEN

0

CLOSE

Battery voltage

Driver

side

M36

62 (SB)

OPEN

0

CLOSE

Battery voltage

PIIA6158E

SUNROOF

RF-37

C

D

E

F

G

H

J

K

L

M

A

B

RF

Revision: 2006 August

2006 Murano

2. 

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect BCM and front door lock assembly (driver side and passenger side) connector.

3.

Check continuity between BCM connector M34, 36 terminals 12, 62 and front door lock assembly connec-
tor D10 (driver side), D38 (passenger side) terminal 4.

4.

Check continuity between BCM connector M34, 36 terminals 12,
62 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness between BCM and front door

lock assembly.

3. 

CHECK DOOR SWITCH

Check continuity between front door lock assembly terminal 4 and 5.

OK or NG

OK

>> GO TO 4. 

NG

>> Replace malfunction front door lock assembly.

Driver side

62 (SB) – 4 (SB)

: Continuity should exist.

Passenger side

12 (R) – 4 (R/G)

: Continuity should exist.

12 (R) – Ground

: Continuity should not exist.

62 (SB) – Ground

: Continuity should not exist.

PIIB0907E

Terminal

Door switch

Continuity

4

5

OPEN

No

CLOSE

Yes

PIIA4220E

RF-38

SUNROOF

Revision: 2006 August

2006 Murano

4. 

CHECK DOOR SWITCH GROUND CIRCUIT

1.

Check continuity between front door lock assembly connector D10 (driver side), D38 (passenger side) ter-
minal 5 and ground.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Repair or replace harness between front door lock

assembly and ground.

5 (B) - Ground

: Continuity should exist.

PIIA9680E

SUNROOF

RF-39

C

D

E

F

G

H

J

K

L

M

A

B

RF

Revision: 2006 August

2006 Murano

Wind Deflector Inspection

NIS001DN

Check that the wind deflector is properly raised by manual. If a mal-
function is detected, remove and visually check it. If it is damaged,
replace it with a new one. If no damage is found, reinstall it properly.

Link and Wire Assembly

NIS001DO

NOTE:
Before replacing a suspect part, carefully ensure it is the source of noise being experienced.
1.

Check link to determine if coated film has peeled off to such an extent that substrate is visible. Check also
to determine if link is the source of noise. If it is, replace it.

2.

Visually check to determine if a sufficient amount of grease has been applied to wire or rail groove. If not,
add grease as required.

3.

Check wire for any damage or deterioration. If any damage is found, replace wire.

Fitting Adjustment

NIS001DP

PIIA5061E

PIIA4248E

RF-40

SUNROOF

Revision: 2006 August

2006 Murano

LID WEATHERSTRIP OVERLAP ADJUSTMENT AND SURFACE MISMATCH ADJUSTMENT

1.

Tilt up glass lid.

2.

After loosening glass lid TORX bolts (T25) (left and right), tilt
down glass lid.

3.

Adjust glass lid from outside of vehicle so it resembles “A–A” “B–
B” “C–C” as shown in the figure.

4.

To prevent glass lid from moving after adjustment, first tighten
the TORX bolts (T25) of front left, and then tighten the TORX
bolts (T25) of rear right.

5.

Tighten remaining TORX bolts (T25), being careful to prevent
glass lid from moving.

6.

Tilt glass lid up and down several times to check that it moves
smoothly.

Removal and Installation

NIS001DQ

●

After any adjustment, check sunroof operation and glass lid alignment.

●

Handle finisher plate and glass lid with care so not to cause damage.

●

It is desirable for easy installation to mark each point before removal.

CAUTION:

●

Always work with a helper.

●

Fully close the glass lid assembly, before removal, then do not operate sunroof motor assembly
after removal.

PIIA3501E

SUNROOF

RF-41

C

D

E

F

G

H

J

K

L

M

A

B

RF

Revision: 2006 August

2006 Murano

PIIB0906E

RF-42

SUNROOF

Revision: 2006 August

2006 Murano

SUNROOF UNIT ASSEMBLY
Removal

CAUTION:

●

Always work with a helper.

●

When taking sunroof unit out, use shop clothes to protect the seats and trim from damage.

●

After installing the sunroof unit and glass lid, be sure to perform the leakage test and make sure
there is no malfunction.

1.

Tilt glass lid up.

2.

Remove the headlining. Refer to 

EI-35, "Removal and Installation"

 .

3.

Disconnect drain hoses.

4.

Remove glass lid. Refer to 

RF-43, "Removal"

 .

5.

Remove motor mounting screws. Remove sunroof motor
assembly and disconnect harness connector.

CAUTION:

●

Before removing sunroof motor assembly, make sure
that sunroof is fully closed.

●

After removing sunroof motor assembly, do not attempt
to rotate sunroof motor as a single unit.

6.

Remove nuts from the front end and side rail.

7.

Remove sunroof bracket bolts, then remove sunroof unit assem-
bly from roof panel.

8.

Remove sunroof unit assembly through the passenger compartment while being careful not to damage
the seats and trim.

1.

Glass lid

2.

TORX bolt

3.

Washer

4.

Rear sunroof bracket

5.

Front sunroof  bracket

6.

Wind defrector

7.

Sunroof unit assembly

8.

Noise cover

9.

Sunroof motor assembly

10. Screw

11.

Sunshade

12. Nut

13. Drain plate

14. Sunshade stopper

PIIA4793E

PIIA5060E

PIIA4241E