Nissan Murano. Manual - part 1377

TM-50

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

P0705 TRANSMISSION RANGE SENSOR A

P0705 TRANSMISSION RANGE SENSOR A

Description

INFOID:0000000009719436

• The transmission range switch is included in the control valve assembly.
• The transmission range switch includes 4 transmission position switches.
• TCM judges the selector lever position by the transmission range switch signal.

DTC Logic

INFOID:0000000009719437

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

With CONSULT

1.

Turn ignition switch ON.

2.

Select “Data Monitor” in “TRANSMISSION”.

3.

Start engine.

4.

Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.

With GST

Follow the procedure “With CONSULT”.
Is “P0705” detected?

YES

>> Go to 

TM-50, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000009719438

1.

CHECK CVT POSITION

1.

Disconnect CVT unit connector.

2.

Remove control cable from manual lever. Refer to

TM-169, "Exploded View"

.

3.

Check transmission range switch. Refer to 

TM-51, "Component Inspection"

.

Is the inspection result normal?

 Shift position

Transmission range 

switch 1

Transmission range 

switch 2

Transmission range 

switch 3

Transmission range 

switch 4

Transmission range 

switch 3 (monitor)

P

OFF

OFF

OFF

OFF

OFF

R

ON

OFF

OFF

ON

OFF

N

ON

ON

OFF

OFF

OFF

D

ON

ON

ON

ON

ON

L

OFF

ON

ON

OFF

ON

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P0705

Transmission Range Sensor 
“A” Circuit (PRNDL Input)

TCM does not receive the correct voltage 
signal (based on the gear position) from the 
switch.

• Harness or connectors

(Transmission range switches circuit is 
open or shorted.)

• Transmission range switch

VEHICLE SPEED

: More than 10 km/h (6 MPH)

ENG SPEED SIG

: More than 450 rpm

ACC PEDAL OPEN

: More than 1.0/8

P0705 TRANSMISSION RANGE SENSOR A

TM-51

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

YES

>> Adjust CVT position. Refer to 

TM-164, "Inspection and Adjustment"

.

NO

>> GO TO 2.

2.

 CHECK HARNESS BETWEEN TCM AND TRANSMISSION RANGE SWITCH (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM vehicle side harness connector terminals and CVT unit vehicle side har-
ness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

 CHECK HARNESS BETWEEN TCM AND TRANSMISSION RANGE SWITCH (PART 2)

Check continuity between TCM vehicle side harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace TCM. Refer to 

TM-165, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Component Inspection

INFOID:0000000009719439

1.

CHECK TRANSMISSION RANGE SWITCH

Check the continuity of the transmission range switch by changing selector lever to various positions and
checking continuity between CVT unit terminals and ground.

 TCM vehicle side harness connector

 CVT unit vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

1

F24

5

Existed

2

14

3

15

4

18

11

4

TCM vehicle side harness connector

Ground

Continuity

Connector Terminal

F23

1

Not existed

2

3

4

11

TM-52

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

P0705 TRANSMISSION RANGE SENSOR A

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace transaxle assembly. Refer to 

TM-180, "Exploded View"

.

Shift position

CVT unit connector

Ground

Continuity

Connector

Terminal

P

F24

4, 5, 14, 15, 18

Not existed

R

4, 15

Existed

5, 14, 18

Not existed

N

4, 5

Existed

14, 15, 18

Not existed

D

4, 5, 14, 15, 18

Existed

L

5, 14, 18

Existed

4, 15

Not existed

P0710 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-53

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0710 TRANSMISSION FLUID TEMPERATURE SENSOR A

Description

INFOID:0000000009719440

The CVT fluid temperature sensor detects the CVT fluid temperature and sends a signal to the TCM.

DTC Logic

INFOID:0000000009719441

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION (PART 1)

1.

Start the engine.

2.

Maintain the following condition for 5 seconds or more.

3.

Stop the vehicle.

4.

Check the first trip DTC.

Is “P0710” detected?

YES

>> Go to 

TM-54, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK DTC DETECTION (PART 2)

With CONSULT

1.

Turn ignition switch OFF and cool the engine.

2.

Turn ignition switch ON.

CAUTION:

Never start the engine.

3.

Select “Data Monitor” in “TRANSMISSION”.

4.

Select “FLUID TEMP”.

5.

Record CVT fluid temperature.

6.

Start the engine and wait for at least 2 minutes.

7.

Drive the vehicle for the total minutes specified in the Driving time column below with the following condi-
tions satisfied.

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P0710

Transmission Fluid Tempera-
ture Sensor “A” Circuit

During running, the CVT fluid temperature 
sensor signal voltage is excessively high or 
low.

• Harness or connectors

(Sensor circuit is open or shorted.)

• CVT fluid temperature sensor

CVT fluid temperature does not rise to 10

°

C 

(50

°

F) after driving for a certain period of 

time with the TCM-received fluid tempera-
ture sensor value between 

−

40

°

C (

−

40

°

F) 

and 9

°

C (48.2

°

F).

The following conditions are maintained for 
5 minutes after the completion of engine di-
agnosis P0111, P0116, and P0196:
• A/T fluid temperature 

−

 Engine coolant 

temperature > 55

°

C (131

°

F)

• A/T fluid temperature 

−

 Engine coolant 

temperature < 

−

27

°

C (

−

16.6

°

F)

A/T fluid temperature sensor

Vehicle speed

: 20 km/h (12 MPH) or more

Selector lever

: “D” position