Nissan X-Trail 32. Manual - part 341

DAS

CAMERA AIMING ADJUSTMENT

DAS-105

< BASIC INSPECTION >

[DRIVER ASSISTANCE SYSTEM]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

Change the magnification of print to 250 mm (9.84 in) 

×

 250 mm (9.84 in) and print the target mark sample.

JSOIA0633ZZ

DAS-106

< BASIC INSPECTION >

[DRIVER ASSISTANCE SYSTEM]

REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION

REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION

Inspection Procedure

INFOID:0000000010727922

1.

CHECK REAR CAMERA WASHER/AIR BLOWER FUNCTION

1.

Start the engine.

2.

Select the ACTIVE TEST item “AIR&WASH ACTIVE” of “AVM” with CONSULT.
NOTE:
Before function check, perform the following items:
• Fill with washer fluid.
• Perform ACTIVE TEST item “WASH ACTIVE” of “AVM” with CONSULT for 4 seconds.

3.

With operating the test item, check the operation.

Is it properly operated?

Washer fluid ejects 4 - 6 times. (Normal function)>>INSPECTION END.
Washer fluid ejects 7 times or more.>>Properly install or replace air tube.
Washer fluid ejects only once>> Properly install or replace air tube.
Washer fluid does not eject>>Properly install washer tube or replace washer tube and check valve.

DAS

ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-

TROL UNIT

DAS-107

< BASIC INSPECTION >

[DRIVER ASSISTANCE SYSTEM]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR
CONTROL UNIT

Description

INFOID:0000000010931470

• Always perform the around view monitor control unit configuration after replacing the around view monitor

control unit.

• Always perform the around view monitor calibration after removing and installing or replacing the rear cam-

era.

• Always perform the rear camera calibration after removing and installing or replacing the rear camera.
• Always perform the rear camera calibration after replacing the around view monitor control unit.
• Always perform the around view monitor calibration after replacing the around view monitor control unit.

CAUTION:

The system does not operate normally unless the around view monitor and rear camera calibration are
performed. Always perform it.

Work Procedure

INFOID:0000000010931471

1.

AROUND VIEW MONITOR CONTROL UNIT CONFIGURATION

Perform the around view monitor control unit configuration with CONSULT. Refer to 

AV-159, "CONFIGURA-

TION (AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure"

.

>> GO TO 2.

2.

AROUND VIEW MONITOR CONTROL UNIT CALIBRATION

Perform the around view monitor calibration with CONSULT. Refer to 

AV-161, "CALIBRATING CAMERA

IMAGE (AROUND VIEW MONITOR) : Work Procedure"

.

>> GO TO 3.

3.

REAR CAMERA CALIBRATION

Perform the rear camera calibration with CONSULT. Refer to 

DAS-110, "Work Procedure (Preparation)"

.

>> GO TO 4.

4.

PERFORM SELF-DIAGNOSIS

Perform the self-diagnosis of around view monitor control unit with CONSULT (AVM). Check if any DTC is
detected.

Is any DTC detected?

YES

>> Perform the trouble diagnosis for the detected DTC. Refer to 

AV-120, "DTC Index"

.

NO

>> GO TO 5.

5.

LDW AND BSW SYSTEM ACTION TEST

1.

Perform the BSW and DAA system action test. Refer to 

DAS-92, "BSW : Work Procedure"

 (BSW) and

DAS-95, "DAA : Work Procedure"

 (DAA).

2.

Check that the BSW and DAA system operates normally.

>> WORK END

DAS-108

< BASIC INSPECTION >

[DRIVER ASSISTANCE SYSTEM]

CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)

CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)

Work Procedure

INFOID:0000000010931472

1.

SAVING VEHICLE SPECIFICATION

CONSULT Configuration

Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
Is the vehicle specification saved normally?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

REPLACE AROUND VIEW MONITOR CONTROL UNIT

Replace around view monitor control unit. Refer to 

AV-268, "Removal and Installation"

.

>> GO TO 3.

3.

WRITING VEHICLE SPECIFICATION

CONSULT Configuration

Select “Configuration” or “After Replace ECU”, and write the vehicle specification saved in CONSULT to
around view monitor control unit.

>> GO TO 6.

4.

REPLACE AROUND VIEW MONITOR CONTROL UNIT

Replace around view monitor control unit. Refer to 

AV-268, "Removal and Installation"

.

>> GO TO 5.

5.

WRITING VEHICLE SPECIFICATION

CONSULT Configuration

Select “WRITE CONFIGURATION - Manual selection” and write in the following list at a around view monitor
control unit depending on a vehicle specification.

>> GO TO 6.

6.

PERFORM SELF-DIAGNOSIS

CONSULT Self Diagnostic Result

Setting item

Detail

Items

Setting value

HANDLE

LHD

LHD models

RHD

RHD models

TRANSMISSION

A/T

CVT models

M/T

M/T models

LDW FUNCTION

WITHOUT

Without LDW

WITH

With LDW

4WD/2WD

2WD

2WD models

4WD

4WD models

DISPLAY

TYPE C

Without navigation system

TYPE G

With navigation system

SONAR

WITHOUT

Without sonar system

WITH

With sonar system