Nissan X-Trail 32. Manual - part 2108

TM-390

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

SHIFT POSITION INDICATOR CIRCUIT

SHIFT POSITION INDICATOR CIRCUIT

Component Parts Function Inspection

INFOID:0000000010622576

1.

CHECK SHIFT POSITION INDICATOR

1.

Start the engine.

2.

Shift selector lever.

3.

Check that the selector lever position and the shift position indicator on the combination meter are identi-
cal.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-390, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010622577

1.

CHECK TCM INPUT/OUTPUT SIGNAL 

With CONSULT

1.

Start the engine.

2.

Select “Data Monitor” in “TRANSMISSION”.

3.

Select “RANGE”. 

4.

Shift selector lever.

5.

Check that selector lever position, “RANGE” on CONSULT screen, and shift position indicator display on
combination meter are identical.

Is the check result normal?

YES

>> INSPECTION END

NO-1 (“RANGE” is changed but is not displayed on shift position indicator.>>Check “Self Diagnostic Result”

in “TRANSMISSION”.

NO-2 (“RANGE” and shift position indicator are different.)>>Check “Self Diagnostic Result” in “TRANSMIS-

SION”.

NO-3 (Specific “RANGE” is not displayed on shift position 

indicator.)>>Check “Self Diagnostic Result” in

“METER/M&A”.

SHIFT LOCK SYSTEM

TM-391

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SHIFT LOCK SYSTEM

Component Function Check

INFOID:0000000010622578

1.

CHECK SHIFT LOCK OPERATION (PART 1)

1.

Turn ignition switch ON.

2.

Shift the selector lever to “P” position.

3.

Attempt to shift the selector lever to any other than position with the brake pedal released.

Can the selector lever be shifted to any other position?

YES

>> Go to 

TM-391, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK SHIFT LOCK OPERATION (PART 2)

Attempt to shift the selector lever to any other than position with the brake pedal depressed.

Can the selector lever be shifted to any other position?

YES

>> INSPECTION END

NO

>> Go to 

TM-391, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010622579

1.

CHECK POWER SOURCE (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp switch connector

3.

Turn ignition switch ON.

4.

Check the voltage between the stop lamp switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 9.

2.

CHECK STOP LAMP SWITCH MOUNTING POSITION

Check stop lamp switch mounting position. Refer to 

BR-11, "Inspection and Adjustment"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Adjust stop lamp switch mounting position.

3.

CHECK STOP LAMP SWITCH

Check stop lamp switch. Refer to 

TM-394, "Component Inspection (Stop Lamp Switch)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace stop lamp switch.

4.

CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR

1.

Disconnect CVT shift selector connector

2.

Check the continuity between the stop lamp switch harness connector terminal and the CVT shift selector
harness connector terminal.

+

–

Voltage

Stop lamp switch

Connector

Terminal

E115

3

Ground

Battery voltage

Stop lamp switch

CVT shift selector

Continuity

Connector

Terminal

Connector

Terminal

E115

4

M52

3

Existed

TM-392

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

SHIFT LOCK SYSTEM

3.

Also check short circuit in harness.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

CHCK GROUND CIRCUIT

Check the continuity between the CVT shift selector harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

6.

CHECK PART POSITION SWITCH

1.

Disconnect park position switch connector.

2.

Check park position switch. Refer to 

TM-393, "Component Inspection (Park Position Switch)"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace damaged parts.

7.

CHECK SHIFT LOCK SOLENOID

1.

Disconnect shift lock solenoid connector.

2.

Check shift lock solenoid. Refer to 

TM-392, "Component Inspection (Shift Lock Solenoid)"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace damaged parts.

8.

CHECK CVT SHIFT SELECTOR HARNESS

Check CVT shift selector harness. Refer to 

TM-393, "Component Inspection (CVT Shift Selector Harness)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Repair or replace damaged parts.

9.

DETECT MALFUNCTIONING ITEM

Check the following items:
• Open or short circuit of the harness between ignition switch and stop lamp switch connector. Refer to 

PG-52,

"Wiring Diagram - IGNITION POWER SUPPLY -"

.

• Ignition switch
• 10A fuse [No.30, fuse block (J/B)]. Refer to 

PG-84, "Fuse, Connector and Terminal Arrangement"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Repair or replace damaged parts.

Component Inspection (Shift Lock Solenoid)

INFOID:0000000010622580

1.

CHECK SHIFT LOCK SOLENOID

Apply voltage to terminals of shift lock solenoid connector and check that shift lock solenoid is activated.

CAUTION:

• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.

CVT shift selector

—

Continuity

Connector

Terminal

M52

4

Ground

Existed

SHIFT LOCK SYSTEM

TM-393

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace shift lock unit. Refer to 

TM-404, "Disassembly and Assembly"

.

Component Inspection (Park Position Switch)

INFOID:0000000010622581

1.

CHECK PARK POSITION SWITCH

Check the continuity between park position switch connector terminals.

CAUTION:

• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace park position switch. Refer to 

TM-404, "Disassembly and Assembly"

.

Component Inspection (CVT Shift Selector Harness)

INFOID:0000000010622582

1.

CHECK CVT SHIFT SELECTOR HARNESS (PART 1)

Check the continuity between the CVT shift selector harness connector terminal and the shift lock solenoid
harness connector terminal.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace CVT shift selector assembly. Refer to 

TM-403, "Removal and Installation"

.

2.

CHECK CVT SHIFT SELECTOR HARNESS (PART 2)

Check the continuity between the shift lock solenoid harness connector terminal and the park position switch
harness connector terminal.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace CVT shift selector assembly. Refer to 

TM-403, "Removal and Installation"

.

3.

CHECK CVT SHIFT SELECTOR HARNESS (PART 3)

Check the continuity between the park position switch harness connector terminal and the CVT shift selector
harness connector terminal.

+ (fuse)

−

Condition

Status

Shift lock solenoid

Terminal

1

2

Apply battery voltage be-
tween terminals 1 and 2.

Shift lock solenoid operates

Park position switch

Condition

Continuity

Terminal

1 – 2

Shift the selector lever to “P” position.

Existed

Other than above

Not existed

CVT shift selector

Shift lock solenoid

Continuity

Connector

Terminal

Connector

Terminal

M324

3

M326

1

Existed

Shift lock solenoid

Park position switch

Continuity

Connector

Terminal

Connector

Terminal

M326

2

M325

1

Existed