Nissan X-Trail 32. Manual - part 1633

PB-58

< BASIC INSPECTION >

CALIBRATION OF G SENSOR

4.

After approx. 10 seconds, touch “END”.

5.

Turn the ignition switch OFF and then turn it ON again.

CAUTION:

• Be sure to perform the operation above.
• Be sure to wait for 10 seconds or more after turning the ignition switch OFF or ON.

>> GO TO 3.

3.

PERFORM THE SELF-DIAGNOSIS

With CONSULT

1.

Pull parking brake switch to activate electric parking brake.

2.

Push parking brake switch to release electric parking brake.

3.

Perform “EHS/PKB” self-diagnosis.

Is malfunction detected?

YES

>> Check the DTC. Refer to 

PB-36, "DTC Index"

. GO TO 4.

NO

>> GO TO 4.

4.

CHECK DATA MONITOR

With CONSULT

1.

Drive the vehicle.

2.

Steer the steering wheel to the straight-ahead position.

3.

Stop the vehicle on level surface.

4.

Select “EHS/PKB”, “DATA MONITOR”, and “SLOPE RATIO” according to this order. Check that signals is
within the specified value. Refer to 

PB-29, "Reference Value"

.

Is the check result normal?

YES

>> GO TO 5.

NO

>> GO TO 1.

5.

ERASE SELF-DIAGNOSIS MEMORY

With CONSULT

1.

Turn the ignition switch OFF to ON. 

CAUTION:

Be sure to wait for 10 seconds or more after turning the ignition switch OFF or ON.

2.

Erase self-diagnosis results memory of “EHS/PKB”.

Is the memory erased?

YES

>> INSPECTION END

NO

>> Check the items indicated by the self-diagnosis.

RESET OF CLUTCH STROKE SENSOR

PB-59

< BASIC INSPECTION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

RESET OF CLUTCH STROKE SENSOR

Description

INFOID:0000000010722944

CAUTION:

When the following operations are performed, always use CONSULT, and carry “CLUTCH SENSOR
RESET” of “WORK SUPPORT”.
NOTE:
This work is M/T models.

×

: Required

 —: not required

Work Procedure

INFOID:0000000010722945

CAUTION:

When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Replacing electric parking brake control module
• Removing/installing clutch stroke sensor
• Replacing clutch stroke sensor
• Removing/installing clutch pedal
• Replacing clutch pedal
NOTE:
This work is M/T models.

1.

CHECK THE VEHICLE STATUS

1.

Stop the vehicle.

2.

Stop the engine.

3.

Turn the ignition switch OFF.

>> GO TO 2.

2.

CHECKING INSTALLATION CONDITION OF CLUTCH COMPONENTS

Check the installation conditions of clutch components.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts and GO TO 3.

3.

PERFORM CLUTCH SENSOR RESET

CAUTION:

Procedure

CLUTCH SENSOR RESET

Removing/installing electric parking brake control module

—

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

—

Removing/installing rear brake pad (When pressing piston of rear brake 
caliper assembly)

—

Replacing rear brake pad

—

Removing/installing rear brake caliper assembly

—

Replacing rear brake caliper assembly

—

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

×

Replacing clutch stroke sensor

×

Removing/installing clutch pedal

×

Replacing clutch pedal

×

PB-60

< BASIC INSPECTION >

RESET OF CLUTCH STROKE SENSOR

• Never allow passenger or load on the vehicle.
• Never apply vibration to the vehicle body when opening or closing door during calibration.

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Select “EHS/PKB”, “WORK SUPPORT”, and “CLUTCH SENSOR RESET” according to this order.

CAUTION:

Never depress the clutch pedal.

3.

Touch “START”.

>> GO TO 4.

4.

PERFORM THE SELF-DIAGNOSIS

With CONSULT

1.

Pull parking brake switch to activate electric parking brake.

2.

Drive the vehicle and check the automatic release.

3.

Perform “EHS/PKB” self-diagnosis.

Is malfunction detected?

YES

>> Check the DTC. Refer to 

PB-36, "DTC Index"

. GO TO 5.

NO

>> GO TO 5.

5.

CHECK DATA MONITOR

With CONSULT

Select “EHS/PKB”, “DATA MONITOR”, and “CLUTCH PEDAL” according to this order. Check that signals are
within the specified value. Refer to 

PB-29, "Reference Value"

.

Is the check result normal?

YES

>> GO TO 6.

NO

>> GO TO 1.

6.

ERASE SELF-DIAGNOSIS MEMORY

With CONSULT

1.

Turn the ignition switch OFF to ON. 

CAUTION:

Be sure to wait for 10 seconds or more after turning the ignition switch OFF or ON.

2.

Erase self-diagnosis results memory of “EHS/PKB”.

Is the memory erased?

YES

>> INSPECTION END

NO

>> Check the items indicated by the self-diagnosis.

OPERATION OF REAR BRAKE CALIPER

PB-61

< BASIC INSPECTION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

OPERATION OF REAR BRAKE CALIPER

Description

INFOID:0000000010722946

CAUTION:

When the following operations are performed, always use CONSULT, for performing “BRAKE OPERA-
TION” of “WORK SUPPORT”.

×

: Required

 —: not required

*: M/T models

Work Procedure

INFOID:0000000010722947

CAUTION:

When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Removing/installing electric parking brake control module
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Removing/installing rear brake caliper assembly
• Replacing rear brake caliper assembly
NOTE:
When the replaced rear brake pad, refer to 

PB-52, "Work Procedure"

.

1.

PERFORM BRAKE OPERATION

With CONSULT

1.

Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.

CAUTION:

• Never operate the parking brake switch.
• Never depress the brake pedal.

2.

Touch “START”.

>> GO TO 2.

2.

PERFORM BRAKE RELEASE

With CONSULT

1.

Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE RELEASE” according to this order.

CAUTION:

Procedure

BRAKE OPERATION

Removing/installing electric parking brake control module

×

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

×

Removing/installing rear brake pad (When pressing piston of rear brake 
caliper assembly)

×

Replacing rear brake pad

×

Removing/installing rear brake caliper assembly

×

Replacing rear brake caliper assembly

×

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

*

—

Replacing clutch stroke sensor

*

—

Removing/installing clutch pedal

*

—

Replacing clutch pedal

*

—