Nissan X-Trail 32. Manual - part 1601

MWI-86

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (COMBINATION METER)

How to Reset Error Code

Error codes stored in combination meter can be reset by following the instructions below:
1.

Turn ignition switch OFF.

2.

While pressing the trip reset switch, turn ignition switch ON. 

3.

Keep the trip reset switch for 1 seconds or more.

4.

Press the trip reset switch at least 3 times. (Within 7 seconds after the ignition switch is turned ON.)

5.

Turn ignition switch OFF.

6.

Perform self-diagnosis and check that the error codes are reset.

CONSULT Function

INFOID:0000000010714997

APPLICATION ITEMS

CONSULT can perform the following diagnosis modes via CAN communication and the combination meter.

SELF DIAG RESULT

Refer to 

MWI-105, "DTC Index"

.

Freeze frame data (FFD)

When DTC is detected, the following vehicle condition is recorded  and it is displayed on the CONSULT
screen.

WORK SUPPORT

Engine coolant temper-
ature gauge

0

Normal

—

1

An engine coolant temperature signal can-
not be received from ECM.

Perform “Self Diagnostic Result” of 
“ECM.” 
Refer to 

EC-109, "DTC Index"

 

(MR20DD), 

EC-517, "DTC Index"

 

(QR25DE), or 

EC-908, "DTC Index"

 

(R9M)

Meter control switch 

0

Normal

—

1

When judging that the display back switch 
signal circuit is short-circuited for 5 minutes 
or more.

Refer to 

MWI-134, "Component Func-

tion Check"

.

2

When judging that the display next switch 
signal circuit is short-circuited for 5 minutes 
or more.

3

When judging that the display next switch, 
and display back switch signal circuit are 
short-circuited for 5 minutes or more.

—

0

Displays “0” constantly.

—

—

0

Displays “0” constantly.

—

—

0

Displays “0” constantly.

—

Item

Code

Description

Action to take/Reference

System

Diagnosis mode

Description

METER/M&A

Self Diagnostic Result

The combination meter checks the conditions and displays memorized errors.

Work Support

Displays diagnosis procedure of each work item.

Data Monitor

Displays the combination meter input/output data in real time.

Warning History

Lighting history of the warning lamp and indicator lamp can be checked.

Item name

Display item

ODO/TRIP METER

Records an odometer value when DTC is detected.
• Current odometer value is shown when the displayed DTC means a present malfunction.
• Odometer value of the time of returning to normal is shown when the displayed DTC means a past 

malfunction.

MWI

DIAGNOSIS SYSTEM (COMBINATION METER)

MWI-87

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

*1: Although a segment type fuel gauge can display work items, it is not used.

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Display Item List

X: Applicable

Work support item

Description

Turn signal buzzer diagnosis

A possible malfunction can be narrowed down by following dis-
played instructions.

Outside air temperature diagnosis

Fuel meter diagnosis (Analog pointer)

*1

Warning/Indicator lamp diagnosis

Display item [Unit]

MAIN

SIGNALS

Description

SPEED METER
[km/h]

X

Value of vehicle speed signal received from ABS actuator and electric unit (control 
unit) via CAN communication.
NOTE:
655.35 is displayed when the malfunction signal is received.

SPEED OUTPUT
[km/h]

X

Vehicle speed signal value transmitted to other units via CAN communication.
NOTE:
655.35 is displayed when the malfunction signal is received.

ODO OUTPUT
[km/h or mph]

Odometer signal value transmitted to other units via CAN communication.

TACHO METER
[rpm]

X

Value of the engine speed signal received from TCM via CAN communication.
NOTE:
8191.875 is displayed when the malfunction signal is received.

FUEL METER
[L]

X

Fuel level indicated on combination meter.

W TEMP METER
[

°

C] 

X

Value of engine coolant temperature signal is received from ECM via CAN com-
munication. 
NOTE:
215 is displayed when the malfunction signal is input.

ABS W/L
[On/Off]

Status of ABS warning lamp detected from ABS warning lamp signal is received 
from ABS actuator and electric unit (control unit) via CAN communication.

VDC/TCS IND
[On/Off]

Status of VDC OFF indicator lamp detected from VDC OFF indicator lamp signal 
is received from ABS actuator and electric unit (control unit) via CAN communica-
tion.

SLIP IND
[On/Off]

Status of VDC warning lamp detected from VDC warning lamp signal received 
from ABS actuator and electric unit (control unit) via CAN communication.

BRAKE W/L
[On/Off]

Status of brake warning lamp detected from brake warning lamp signal is received 
from ABS actuator and electric unit (control unit) via CAN communication and 
brake fluid level switch signal from brake fluid level switch.
NOTE:
Displays “Off” if the brake warning lamp is illuminated when the valve check starts, 
the parking brake switch is turned ON or the brake fluid level switch is turned ON.

DOOR W/L
[On/Off]

Status of door open warning detected from door switch signal received from BCM 
via CAN communication.

TRUNK/GLAS-H
[Off]

NOTE:
This item is displayed, but cannot be monitored.

HI-BEAM IND
[On/Off]

Status of high beam indicator lamp detected from high beam request signal is re-
ceived from BCM via CAN communication.

TURN IND
[On/Off]

Status of turn signal indicator lamp detected from turn indicator signal is received 
from BCM via CAN communication.

MWI-88

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (COMBINATION METER)

FR FOG IND
[On/Off]

Status of front fog lamp indicator lamp detected from front fog light request signal 
is received from BCM via CAN communication.

RR FOG IND
[On/Off]

Status of rear fog lamp indicator lamp detected from rear fog lamp status signal is 
received from BCM via CAN communication.

LIGHT IND
[On/Off]

Status of position lamp indicator lamp detected from position light request signal 
is received from BCM via CAN communication. 

OIL W/L
[On/Off]

Status of engine oil pressure warning detected from engine oil pressure warning 
lamp signal is received from ECM via CAN communication.

MIL
[On/Off] 

Status of malfunction indicator lamp (yellow) detected from malfunctioning indica-
tor signal is received from ECM via CAN communication.

GLOW IND
[On/Off]

Status of glow indicator lamp detected from glow indicator lamp signal is received 
from ECM via CAN communication.

C-ENG2 W/L
[On/Off]

Status of malfunction indicator lamp (red) detected from malfunctioning indicator 
signal is received from ECM via CAN communication.

BA W/L
[Off]

NOTE:
This item is displayed, but cannot be monitored.

4WD W/L
[On/Off] 

Status of 4WD warning detected from 4WD warning signal is received from 4WD 
control unit via CAN communication.

4WD LOCK IND
[On/Off] 

Status of LOCK indicator lamp detected from LOCK indicator lamp signal is re-
ceived from 4WD control unit via CAN communication.

FUEL W/L
[On/Off]

Low fuel warning lamp status detected by the identified fuel level.

WASHER W/L
[Off]

NOTE:
This item is displayed, but cannot be monitored.

KEY G/Y W/L
[On/Off]

Status of Intelligent key system malfunction detected from meter display signal is 
received from BCM via CAN communication.

EPS W/L
[On/Off]

Status of electric power steering warning lamp detected from electric power steer-
ing warning lamp signal is received from EPS control unit via CAN communica-
tion.

DDS W/L
[On/Off]

Status of hill descent control indicator lamp detected from hill descent control in-
dicator lamp signal is received from chassis control module via CAN communica-
tion.

CHAGE W/L
[On/Off]

Status of charge warning lamp detected from charge warning lamp signal is re-
ceived from ECM via CAN communication.

4WD AUTO IND
[On/Off]

Status of 4WD indicator lamp detected from 4WD indicator lamp signal is received 
from 4WD control unit via CAN communication.

TRAILER IND
[Off]

NOTE:
This item is displayed, but cannot be monitored.

FILTER W/L
[On/Off]

Status of water-in-fuel-filter warning lamp detected from water-in-fuel-filter warn-
ing lamp signal is received from ECM via CAN communication.

LCD
[B&P, C&P,  ID NG, ROTAT, SFT P, 
NO KY,KY>PSW, IGN AUTO OFF, 3 
min before IGN OFF, Off]

Status of engine start operation indicator lamp, shift P warning lamp and KEY 
warning lamp, detected from engine start operation indicator lamp signal, shift P 
warning lamp signal and key warning lamp signal are received from BCM via CAN 
communication.

SHIFT IND
[P, R, N, D, M1, M2, M3, M4, M5, M6, 
M7]

Status of shift position indicator judged from shift position signal received from 
TCM with CAN communication line.

O/D OFF SW
[Off]

NOTE:
This item is displayed, but cannot be monitored.

M RANGE SW
[On/Off]

Status of manual mode switch.

NM RANGE SW
[On/Off]

Status of non-manual mode switch.

Display item [Unit]

MAIN

SIGNALS

Description

MWI

DIAGNOSIS SYSTEM (COMBINATION METER)

MWI-89

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

AT SFT UP SW
[On/Off]

Status of manual mode shift up switch.

AT SFT DWN SW
[On/Off]

Status of manual mode shift down switch.

ST SFT UP SW
[Off]

NOTE:
This item is displayed, but cannot be monitored.

ST SFT DWN SW
[Off]

NOTE:
This item is displayed, but cannot be monitored.

COMP F/B SIG
[On/Off]

A/C compressor activation condition that ECM judges according to the engine 
coolant temperature and the acceleration degree.

PKB SW
[Off]

NOTE:
This item is displayed, but cannot be monitored.

BUCKLE SW
[On/Off]

Status of front seat belt buckle switch (driver side).

BRAKE OIL SW
[On/Off]

Status of brake fluid level switch.

ECO MODE SW
[On/Off]

Status of ECO mode switch.

CHG CONCT DET
[Off]

NOTE:
This item is displayed, but cannot be monitored.

DISTANCE
[km] or [Mi]

Value of distance to empty calculated by combination meter.

OUTSIDE TEMP
[

°

C or 

°

F]

Ambient temperature value converted from ambient sensor signal received from 
ambient sensor.
NOTE:
This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the ambient 
sensor input value.)

BUZZER
[On/Off]

X

Buzzer status (in the combination meter) is detected from the buzzer output signal 
received from each unit via CAN communication and the warning output condition 
of the combination meter.

ENG OIL TMP
[Off]

NOTE:
This item is displayed, but cannot be monitored.

TRQ DSTRBT
[%]

NOTE:
This item is displayed, but cannot be monitored.

AMT P SFT
[Off]

NOTE:
This item is displayed, but cannot be monitored.

AMT SYS CHCK
[Off]

NOTE:
This item is displayed, but cannot be monitored.

AMT SFT POSI
[Off]

NOTE:
This item is displayed, but cannot be monitored.

AMT OIL TMP H
[Off]

NOTE:
This item is displayed, but cannot be monitored.

AMT CHCK
[Off]

NOTE:
This item is displayed, but cannot be monitored.

AMT CL TMP H
[Off]

NOTE:
This item is displayed, but cannot be monitored.

AMT MALF
[Off]

NOTE:
This item is displayed, but cannot be monitored.

TPMS FLT TIRE
[On/Off]

Status of flat tire detected from tire pressure data signal is received from BCM via 
CAN communication.

TPMS PRESS L
[On/Off]

Status of tire pressure low from tire pressure data signal is received from BCM via 
CAN communication

Display item [Unit]

MAIN

SIGNALS

Description