Nissan Qashqai J11. Manual - part 228

 

  Index      Nissan     Nissan Qashqai J11 - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  226  227  228  229   ..

 

 

Nissan Qashqai J11. Manual - part 228

 

 

ECH-210

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

P0335 CKP SENSOR (POS)

P0335 CKP SENSOR (POS)

DTC Logic

INFOID:0000000010379102

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

Turn ignition switch OFF and wait at least 12 minutes.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Start the engine and let it idle at least 1 second.

2.

Check DTC.

Is DTC detected?

YES

>> Proceed to 

ECH-210, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010379103

1.

CHECK CKP SENSOR (POS) HARNESS CONNECTOR CONNECTIONS

1.

Turn ignition switch OFF.

2.

Check crankshaft position (CKP) sensor (POS) harness connector connection.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace crankshaft position (CKP) sensor (POS) harness connector connection.

2.

CHECK CKP SENSOR (POS) CIRCUIT FOR OPEN AND SHORT

1.

Disconnect ECM harness connector.

2.

Check the continuity CKP sensor (POS) circuit.

3.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 3.

3.

CHECK CKP SENSOR (POS) INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Disconnect crankshaft position (CKP) sensor (POS) harness connector.

2.

Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0335

CRANK POS SEN (OBD) 
[P0335]
(Crankshaft position sensor 
“A” circuit)

• The crankshaft position (CKP) sensor sig-

nal is not detected by the ECM during the 
first few seconds of engine cranking.

• Crankshaft position (CKP) sensor signal 

is not in the normal pattern when engine 
started for 1 second or more.

• ECM cannot detect crankshaft position 

sensor signal when engine started.

• Crankshaft position sensor signal is noisy.

• Harness or connectors

(The sensor circuit is open or shorted.)

• Crankshaft position sensor (POS)
• Signal plate

ECM

Continuity

Connector

Terminal

Terminal

F17

35

37

Existed

P0335 CKP SENSOR (POS)

ECH-211

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

C

D

E

F

G

H

I

J

K

L

M

A

ECH

N

P

O

3.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

4.

CHECK CKP SENSOR (POS) GROUND CIRCUIT FOR OPEN AND SHORT

1.

Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.

2.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

5.

CHECK GEAR TOOTH

Visually check for chipping flywheel gear tooth.

Is the inspection result normal?

YES

>> Replace crankshaft position sensor (POS).

NO

>> Replace signal plate.

CKP sensor (POS)

ECM

Continuity

Connector

Terminal

Connector

Terminal

F8

3

F17

35

Existed

CKP sensor (POS)

ECM

Continuity

Connector

Terminal

Connector

Terminal

F8

2

F17

37

Existed

ECH-212

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

P0340 CMP SENSOR (PHASE)

P0340 CMP SENSOR (PHASE)

DTC Logic

INFOID:0000000010500336

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

Turn ignition switch OFF and wait at least 12 minutes.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Rev engine from idle to 4,000 rpm.

2.

Check DTC.

Is DTC detected?

YES

>> Proceed to 

ECH-212, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010500337

1.

CHECK STARTING SYSTEM

Turn ignition switch to START position.
Does the engine turn over? Does the starter motor operate?

YES

>> GO TO 2.

NO

>> Check starting system.

2.

CHECK CAMSHAFT POSITION (CMP) SENSOR POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Disconnect camshaft position (CMP) sensor harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between CMP sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

CHECK CAMSHAFT POSITION (CMP) SENSOR POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between CMP sensor harness connector and ECM harness connector.

DTC No.

CONSULT screen terms

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P0340

CAMSHAFT POSI SEN 
[P0340]
(Camshaft position sen-
sor “A” circuit bank 1)

• The cylinder No. signal is not sent to ECM for 

the first few seconds during engine cranking.

• The cylinder No. signal is not sent to ECM 

during engine running.

• The cylinder No. signal is not in the normal 

pattern during engine running.

• Harness or connectors

(Camshaft position sensor circuit is open 
or shorted)

• Camshaft position sensor
• Camshaft (Intake)

+

−

Voltage

(Approx.)

CMP sensor

Connector

Terminal

F111

1

Ground

5 V

P0340 CMP SENSOR (PHASE)

ECH-213

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

C

D

E

F

G

H

I

J

K

L

M

A

ECH

N

P

O

4.

Also check harness for short to power.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace error-detected parts.

4.

CHECK CMP SENSOR GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between CMP sensor harness connector and ECM harness connector.

4.

Also check harness for short to power.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts.

5.

CHECK CMP SENSOR INPUT SIGNAL CIRCUIT

1.

Disconnect ECM harness connector.

2.

Check the continuity between CMP sensor harness connector and ECM harness connector.

3.

Also check harness for short to ground and to power.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace error-detected parts.

6.

CHECK CAMSHAFT POSITION SENSOR

Check the camshaft position sensor. Refer to 

ECH-214, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace camshaft position sensor.

7.

CHECK CAMSHAFT (INT)

Check the following.
• Accumulation of debris to the signal plate of camshaft rear end
• Chipping signal plate of camshaft rear end
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Remove debris and clean the signal plate of camshaft rear end or replace camshaft.

+

−

Continuity

CMP sensor

ECM

Connector

Terminal

Connector

Terminal

F111

1

F18

133

Existed

+

−

Continuity

CMP sensor

ECM

Connector

Terminal

Connector

Terminal

F111

2

F18

134

Existed

+

−

Continuity

CMP sensor

ECM

Connector

Terminal

Connector

Terminal

F111

3

F18

135

Existed

 

 

 

 

 

 

 

Content   ..  226  227  228  229   ..