Nissan Qashqai J11. Manual - part 2212

DAS-262

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BB5-00 IGNITION POWER SUPPLY

NO

>> INSPECTION END

3.

CHECK FUSE

1.

Turn the ignition switch OFF.

2.

Check that any of the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair the applicable circuit. And then replace the fuse.

4.

CHECK CHASSIS CONTROL MODULE IGNITION POWER SUPPLY

1.

Disconnect chassis control module harness connector.

2.

Check the voltage between chassis control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK CHASSIS CONTROL MODULE GROUND CIRCUIT

1.

Turn the ignition switch OFF.

2.

Check the continuity between chassis control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

PERFORM SELF-DIAGNOSIS 2

1.

Connect chassis control module harness connector.

2.

Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.

Is DTC “C1BB5-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

NO

>> INSPECTION END

Signal name

Fuse No.

Ignition power supply

4 (10A)

Chassis control module

Ignition switch

—

Voltage

Connector

Terminal

M43

10

OFF

Ground

Approx. 0 V

ON

6.4 – 16 V

Chassis control module

—

Continuity

Connector

Terminal

M43

12

Ground

Existed

DAS

C1BB6-00 IGNITION POWER SUPPLY

DAS-263

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1BB6-00 IGNITION POWER SUPPLY

DTC Description

INFOID:0000000010417011

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Fuse
• Ignition power supply system
• Battery
• Chassis control module

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.

Is DTC “C1BB6-00” detected?

YES

>> Proceed to 

DAS-263, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: Inspection End.

Diagnosis Procedure

INFOID:0000000010417012

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect chassis control module harness connector

3.

Check the connector for disconnection or looseness.

4.

Check the pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts, securely lock the harness connector, and GO TO 2.

2.

PERFORM SELF-DIAGNOSIS 1

1.

Connect chassis control module harness connector.

2.

Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.

Is DTC “C1BB6-00” detected?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

CHECK FUSE

1.

Turn the ignition switch OFF.

2.

Check that any of the following fuse is not fusing.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB6-00

IGNITION POWER SUPPLY
(ignition power supply)

Ignition power supply voltage of chassis control module is as shown below.
• Ignition power supply voltage: 16 V 

≤

 Ignition power supply voltage

DAS-264

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BB6-00 IGNITION POWER SUPPLY

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair the applicable circuit. And then replace the fuse.

4.

CHECKCHASSIS CONTROL MODULE IGNITION POWER SUPPLY

1.

Disconnect chassis control module harness connector.

2.

Check the voltage between chassis control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK CHASSIS CONTROL MODULE GROUND CIRCUIT

1.

Turn the ignition switch OFF.

2.

Check the continuity between chassis control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

PERFORM SELF-DIAGNOSIS 2

1.

Connect chassis control module harness connector.

2.

Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.

Is DTC “C1BB6-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

NO

>> INSPECTION END

Signal name

Fuse No.

Ignition power supply

4 (10A)

Chassis control module

Ignition switch

—

Voltage

Connector

Terminal

M43

10

OFF

Ground

Approx. 0 V

ON

6.4 – 16 V

Chassis control module

—

Continuity

Connector

Terminal

M43

12

Ground

Existed

DAS

C1BB7-00 CONTROL MODULE

DAS-265

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1BB7-00 CONTROL MODULE

DTC Description

INFOID:0000000010417013

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB7-00” detected?

YES

>> Proceed to 

DAS-265, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417014

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB7-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB7-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.