Nissan Qashqai J11. Manual - part 2210

DAS-254

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BA2-00 STEERING ANGLE SENSOR

NO

>> INSPECTION END

DAS

C1BA5-00 ADAS/CHASSIS CONTROL ENGINE SYSTEM

DAS-255

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1BA5-00 ADAS/CHASSIS CONTROL ENGINE SYSTEM

DTC Description

INFOID:0000000010416999

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis Control Module

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BA5-00” detected?

YES

>> Proceed to 

DAS-255, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417000

1.

CHECK ECM SYSTEM

With CONSULT

Perform self-diagnosis for “ECM”.
Is DTC detected?

YES

>> Check the DTC. Refer to 

ECH-71, "DTC Index"

 (HRA2DDT), 

ECM-93, "DTC Index"

 (MR20DD),

ECK-97, "DTC Index"

 (K9K) or 

EC9-108, "DTC Index"

 (R9M).

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

Is DTC “C1BA5-00”, “U1000-00” or other DTC detected?

YES (“C1BA5-00”)>>Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

DAS-286, "Diagnosis Procedure"

.

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BA5-00

ADAS/CHASSIS CTRL ENGINE 
SYS
(ADAS/Chassis control engine 
system)

• When receiving from ECM that the value of the engine system signal transmitted 

from the chassis control module to ECM is malfunctioning.

DAS-256

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BAB-00 STOP LAMP SWITCH

C1BAB-00 STOP LAMP SWITCH

DTC Description

INFOID:0000000010417001

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Stop lamp switch
• BCM
• Chassis Control Module

FAIL-SAFE

The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BAB-00” detected?

YES

>> Proceed to 

DAS-256, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417002

1.

CHECK STOP LAMP SWITCH SYSTEM

With CONSULT

Perform self-diagnosis for “BCM”.

Is DTC detected?

YES

>> Check the DTC. Refer to 

BCS-90, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

Is DTC “C1BAB-00”, “U1000-00” or other DTC detected?

YES (“C1BAB-00”)>>Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

DAS-286, "Diagnosis Procedure"

.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BAB-00

STOP LAMP SW
(Stop lamp switch)

When a malfunction is detected in stop lamp switch system.

DAS

C1BAB-00 STOP LAMP SWITCH

DAS-257

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END