Nissan Qashqai J11. Manual - part 2211

DAS-258

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BB2-00 CONTROL MODULE

C1BB2-00 CONTROL MODULE

DTC Description

INFOID:0000000010417003

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB2-00” detected?

YES

>> Proceed to 

DAS-258, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417004

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB2-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB2-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.

DAS

C1BB3-00 CONTROL MODULE

DAS-259

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1BB3-00 CONTROL MODULE

DTC Description

INFOID:0000000010417005

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB3-00” detected?

YES

>> Proceed to 

DAS-259, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417006

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB3-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB3-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.

DAS-260

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BB4-00 CONTROL MODULE

C1BB4-00 CONTROL MODULE

DTC Description

INFOID:0000000010417007

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB4-00” detected?

YES

>> Proceed to 

DAS-260, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417008

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB4-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB4-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.

DAS

C1BB5-00 IGNITION POWER SUPPLY

DAS-261

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1BB5-00 IGNITION POWER SUPPLY

DTC Description

INFOID:0000000010417009

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Fuse
• Ignition power supply system
• Battery
• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB5-00” detected?

YES

>> Proceed to 

DAS-261, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: Inspection End.

Diagnosis Procedure

INFOID:0000000010417010

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect chassis control module harness connector

3.

Check the connector for disconnection or looseness.

4.

Check the pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts, securely lock the harness connector, and GO TO 2.

2.

PERFORM SELF-DIAGNOSIS 1

1.

Connect chassis control module harness connector.

2.

Perform “Self Diagnostic Result” for “CHASSIS CONTROL”.

Is DTC “C1BB5-00” detected?

YES

>> GO TO 3.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB5-00

IGN POWER SUPPLY
(Ignition power supply)

Ignition power supply voltage of chassis control module is as shown below.
• Ignition power supply voltage: 6.4 V 

≥

 Ignition power supply voltage