Nissan Qashqai J11. Manual - part 2129

AV

U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT

AV-205

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness or connectors.

2.

CHECK LH SIDE CAMERA POWER SUPPLY VOLTAGE

1.

Connect around view monitor control unit and LH side camera connectors.

2.

Turn ignition switch ON.

3.

Check voltage between around view monitor control unit connector M8 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace around view monitor control unit. Refer to 

AV-267, "Removal and Installation"

.

3.

CHECK LH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect around view monitor control unit and LH side camera connectors.

3.

Check continuity between around view monitor control unit connector M8 and LH side camera connector
D3.

4.

Check continuity between around view monitor control unit connector M8 and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness or connectors.

4.

CHECK LH SIDE CAMERA IMAGE SIGNAL

1.

Connect around view monitor control unit and LH side camera connectors.

2.

Turn ignition switch ON.

3.

Check signal between the terminals of around view monitor control unit connector M8.

Around view monitor control unit

Ground

Continuity

Connector

Terminal

M8

56

No

Around view monitor control unit

Ground

Condition

Voltage

(Approx.)

Connector

Terminal

M8

56

—

CAMERA switch is ON or 
selector lever in R (re-
verse).

6.0 V

Around view monitor control unit

LH side camera

Continuity

Connector

Terminals

Connector

Terminals

M8

59

D3

16

Yes

60

15

Around view monitor control unit

Ground

Continuity

Connector

Terminal

M8

59

No

AV-206

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION]

U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT

Is the inspection result normal?

YES

>> Replace around view monitor control unit. Refer to 

AV-267, "Removal and Installation"

.

NO

>> Replace LH side camera. Refer to 

AV-269, "Removal and Installation"

.

Around view monitor control unit connector M8

Condition

Reference value

(+)

(

−

)

Terminal

Terminal

59

60

CAMERA switch is ON or se-
lector lever in R (reverse).

JSNIA0834GB

AV

U112F EPS CIRCUIT

AV-207

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

U112F EPS CIRCUIT

DTC Logic

INFOID:0000000010944762

DTC DETECTION LOGIC

POSSIBLE CAUSE

EPS

FAIL-SAFE

Around view monitor with Park Assist is cancel

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

WITH CONSULT

1.

Turn the ignition switch ON

2.

Perform “All DTC Reading” with CONSULT.

3.

Check if the “U112F” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.

“U112F” detected as the current malfunction?

YES

>> Refer to 

AV-207, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010944763

1.

CHECK SELF-DIAGNOSIS RESULTS

With CONSULT.

Check if the “U1000” is detected other than “U112F” in “Self Diagnostic Result” of “AVM”. 
“U1000” detected?

YES

>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.

Refer to 

AV-189, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK SELF-DIAGNOSIS RESULTS

With CONSULT.

Check if any DTC is detected in “Self Diagnostic Result” of “EPS/DAST3”. 
Is any DTC detected?

YES

>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to

STC-19, "DTC Index"

.

NO

>> Replace the around view monitor control unit. Refer to 

AV-267, "Removal and Installation"

. 

DTC

Trouble diagnosis

(Trouble diagnosis contents)

DTC detecting condition

U112F

EPS CIRC
(EPS circuit)

The around view monitor control unit detects that EPS has a malfunction.

AV-208

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION]

U1217 AV CONTROL UNIT

U1217 AV CONTROL UNIT

DTC Logic

INFOID:0000000010435698

DTC DETECTION LOGIC

CONSULT Display

DTC Detection Condition

Possible Cause

BLUETOOTH MODULE
[U1217]

Connection failure to the internal Blueooth

®

 sub 

unit is detected.

Replace AV control unit if malfunction occurs 
constantly.
Refer to 

AV-259, "Removal and Installation"

.