Nissan Qashqai J11. Manual - part 1744

EXL-278

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

PARKING LAMP CIRCUIT

Is the inspection result normal?

YES

>> Replace the corresponding front combination lamp. Refer to 

EXL-318, "Removal and Installation"

.

NO

>> Repair or replace harness.

Front combination lamp

—

Continuity

Connector

Terminal

RH

E92

1

Ground

Existed

LH

E90

TAIL LAMP CIRCUIT

EXL-279

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

TAIL LAMP CIRCUIT

Component Function Check

INFOID:0000000010469978

1.

CHECK TAIL LAMP OPERATION

With CONSULT

1.

Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

2.

With operating the test items, check that the tail lamp is turned ON.

Is the inspection result normal?

YES

>> Tail lamp circuit is normal.

NO

>> Refer to 

EXL-279, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010469979

1.

CHECK TAIL LAMP OUTPUT VOLTAGE

With CONSULT

1.

Turn ignition switch OFF.

2.

Disconnect the following connectors.

-

Stop lamp / tail lamp LH (body side)

-

Stop lamp / tail lamp RH (body side)

-

Tail lamp LH (back door side)

-

Tail lamp RH (back door side)

3.

Turn ignition switch ON.

4.

Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

5.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

2.

CHECK TAIL LAMP POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and each tail lamp harness connector.

Body side

On

: Tail Lamp ON

Off

: Tail lamp OFF

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

RH

E37

17

Ground

TAIL LAMP

On

9 – 16 V

Off

0 – 1 V

LH

4

On

9 – 16 V

Off

0 – 1 V

IPDM E/R

Stop lamp / tail lamp (body side)

Continuity

Connector

Terminal

Connector

Terminal

RH

E37

17

B79

3

Existed

LH

4

B22

EXL-280

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

TAIL LAMP CIRCUIT

Back door side

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK TAIL LAMP GROUND CIRCUIT

Check continuity between each tail lamp harness connector and ground.

Body side

Back door side

Is the inspection result normal?

YES

>> Replace the corresponding rear combination lamp. Refer to 

EXL-330, "Removal and Installation"

.

NO

>> Repair or replace harness.

IPDM E/R

Tail lamp (back door side)

Continuity

Connector

Terminal

Connector

Terminal

RH

E37

17

D85

1

Existed

LH

4

B29

Stop lamp / tail lamp (body side)

—

Continuity

Connector

Terminal

RH

B79

2

Ground

Existed

LH

B22

Tail lamp (back door side)

—

Continuity

Connector

Terminal

Terminal

RH

D85

2

Ground

Existed

LH

B29

LICENSE PLATE LAMP CIRCUIT

EXL-281

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

LICENSE PLATE LAMP CIRCUIT

Component Function Check

INFOID:0000000010469980

1.

CHECK TAIL LAMP LH OPERATION

Check that tail lamp LH is turned ON when lighting switch is turned 1ST.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check tail lamp circuit. Refer to 

EXL-279, "Component Function Check"

.

2.

CHECK LICENSE PLATE LAMP OPERATION

With CONSULT

1.

Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

2.

With operating the test items, check that the license plate lamp is turned ON.

Is the inspection result normal?

YES

>> License plate lamp circuit is normal.

NO

>> Refer to 

EXL-281, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010469981

1.

CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector and license plate lamp connector.

3.

Check continuity between IPDM E/R harness connector and license plate lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK LICENSE PLATE LAMP GROUND CIRCUIT

Check continuity between license plate lamp harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK LICENSE PLATE LAMP BULB

Check the applicable license plate lamp bulb.
Is the inspection result normal?

YES

>> Check the corresponding license plate lamp bulb socket. Repair or replace if necessary.

NO

>> Replace the corresponding license plate lamp bulb. Refer to 

EXL-334, "Replacement"

.

On

: License plate lamp ON

Off

: License plate lamp OFF

IPDM E/R

License plate lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E37

4

D97

1

Existed

LH

D96

License plate lamp

—

Continuity

Connector

Terminal

RH

D97

2

Ground

Existed

LH

D96