Nissan Qashqai J11. Manual - part 1526

ANTI-PINCH INSPECTION

RF-15

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

ANTI-PINCH INSPECTION

Description

INFOID:0000000010286634

Check anti-pinch function when the initialization of sunshade system is performed. Refer to 

RF-15, "Work Pro-

cedure"

.

Work Procedure

INFOID:0000000010286635

1.

CHECK ANTI-PINCH FUNCTION

1.

Fully open the sunshade.

2.

Place a piece of wood near fully closed position.

3.

Close the sunshade completely with auto-slide close.

4.

Check that sunshade opens fully and stops. 

CAUTION:

• Perform initialization procedure setting when auto-slide operation or anti-pinch function does not

operate normally.

• Check that auto-slide operates before inspection when system initialization is performed.
• Do not check with hands and other part of body because they may be pinched. Do not get pinched.
• Depending on environment and driving conditions, if a similar impact or load is applied to the sun-

shade it may open.

• Thermal cut out may occur if open/close operation is performed continuously. In this situation allow

system to cool before re-use.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Perform initialization procedure. Refer to 

RF-14, "Description"

.

RF-16

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

DTC/CIRCUIT DIAGNOSIS

POWER SUPPLY AND GROUND CIRCUIT

SUNSHADE MOTOR ASSEMBLY

SUNSHADE MOTOR ASSEMBLY : Diagnosis Procedure

INFOID:0000000010286636

1.

CHECK FUSE AND FUSIBLE LINK

1.

Turn ignition switch OFF.

2.

Check that any of the following fuse and fusible link is fusing.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the applicable circuit. And then replace the fuse or fusible link.

2.

CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY 1

1.

Disconnect sunshade motor assembly connector.

2.

Check voltage between sunshade motor assembly harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 4.

3.

CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY 2

1.

Turn ignition switch ON.

2.

Check voltage between sunshade motor assembly harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

4.

CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY CIRCUIT 1

1.

Disconnect circuit breaker connector.

2.

Check voltage between circuit breaker harness connector and ground.

Is the inspection result normal?

Fuse No.

Signal name

14 (10A)

Ignition (ACC or ON) power supply

Fusible link No.

Signal name

M (50A)

Battery power supply

(+)

(

−

)

Voltage

Sunshade motor assembly 

 Connector

Terminal 

R11

7

Ground

9 - 16 V

(+)

(

−

)

Voltage

Sunshade motor assembly 

 Connector

Terminal 

R11

10

Ground

9 - 16 V

(+)

(

−

)

Voltage

Circuit breaker

 Connector

Terminal 

M86

1

Ground

9 - 16 V

POWER SUPPLY AND GROUND CIRCUIT

RF-17

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY CIRCUIT 2

Check continuity between circuit breaker harness connector and sunshade motor assembly harness connec-
tor.

Is the inspection result normal?

YES

>> Replace circuit breaker.

NO

>> Repair or replace harness.

6.

CHECK SUNSHADE MOTOR ASSEMBLY GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between sunshade motor assembly harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace harness.

Circuit breaker

Sunshade motor assembly

Continuity

Connector

Terminal

 Connector

Terminal

M86

2

R11

7

Existed

Sunshade motor assembly

Ground

Continuity 

 Connector

Terminal

R11

1

Existed

RF-18

< DTC/CIRCUIT DIAGNOSIS >

SUNSHADE SWITCH

SUNSHADE SWITCH

Component Function Check

INFOID:0000000010286639

1.

CHECK FUNCTION

Check sunshade open and close operations with sunshade switch.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

RF-18, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010286640

1.

CHECK SUNSHADE SWITCH INPUT SIGNAL 

1.

Turn ignition switch OFF.

2.

Disconnect sunshade switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between sunshade switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SUNSHADE SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect sunshade motor assembly connector.

3.

Check continuity between sunshade switch harness connector and sunshade motor assembly harness
connector.

4.

Check continuity between sunshade switch harness connector and ground. 

Is the inspection result normal?

YES

>> Replace sunshade motor assembly. Refer to 

RF-30, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK SUNSHADE SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between sunshade switch harness connector and ground.

(+)

(

−

)

Voltage

Sunshade switch

Connector

Terminal

R16

1

Ground

9 - 16 V

3

Sunshade switch

Sunshade motor assembly

Continuity

Connector

Terminal

 Connector

Terminal

R16

1

R11

8

Existed

3

6

Sunshade switch

Ground

Continuity

 Connector

Terminal

R16

1

Not existed

3