Nissan Qashqai J11. Manual - part 1527

SUNSHADE SWITCH

RF-19

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness or connector.

4.

CHECK SUNSHADE SWITCH

Check sunshade switch.
Refer to 

RF-19, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Replace sunshade switch. Refer to 

RF-35, "Removal and Installation"

.

Component Inspection

INFOID:0000000010286641

1.

CHECK SUNSHADE SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sunshade switch connector.

3.

Check continuity sunshade switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sunshade switch. Refer to 

RF-35, "Removal and Installation"

.

Sunshade switch

Ground

Continuity 

 Connector

Terminal

R16

2

Existed

Terminal

Condition

Continuity

1

2

Sunshade switch

Open position

Existed

Other than the above

Not existed

3

Close position

Existed

Other than the above

Not existed

RF-20

< SYMPTOM DIAGNOSIS >

SUNSHADE DOES NOT OPERATE PROPERLY

SYMPTOM DIAGNOSIS

SUNSHADE DOES NOT OPERATE PROPERLY

Description

INFOID:0000000010286642

Sunshade does not operate normally.
• Sunshade does not slide.
• Judder occurs during sliding operation of sunshade.
• Sliding operation of sunshade is slow.

Diagnosis Procedure

INFOID:0000000010286643

1.

CHECK SUNSHADE MECHANISM

Check the following.
• Operation malfunction caused by sunshade mechanism deformation, pinched harness or other foreign

materials.

• Operation malfunction and interference with other parts by poor installation.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY AND GROUND CIRCUIT

Check sunshade motor assembly power supply and ground circuit.
Refer to 

RF-16, "SUNSHADE MOTOR ASSEMBLY : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK SUNSHADE SWITCH

Check sunshade switch.
Refer to 

RF-18, "Component Function Check"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Repair or replace the malfunctioning parts.

AUTO OPERATION DOES NOT OPERATE

RF-21

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

AUTO OPERATION DOES NOT OPERATE

Description

INFOID:0000000010286644

Auto operation does not operate
• Auto operation of sunshade does not operate.
• Sunshade stops halfway.
• Anti-pinch function operates.

Diagnosis Procedure

INFOID:0000000010286645

1.

CHECK SUNSHADE MECHANISM

Check the following.
• Operation malfunction caused by sunshade mechanism deformation, pinched harness or other foreign

materials.

• Operation malfunction and interference with other parts by poor installation.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 
Refer to 

RF-14, "Description"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Replace sunshade motor assembly. Refer to 

RF-30, "Removal and Installation"

.

RF-22

< SYMPTOM DIAGNOSIS >

SUNSHADE DOES NOT OPERATE ANTI-PINCH FUNCTION

SUNSHADE DOES NOT OPERATE ANTI-PINCH FUNCTION

Diagnosis Procedure

INFOID:0000000010286646

1.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 
Refer to 

RF-14, "Description"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.