Nissan Juke (2014 year). Service Repair Manual - part 128

EXL-72

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

OPTICAL SENSOR

*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace the optical sensor.

4.

CHECK OPTICAL SENSOR OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect optical sensor connector and BCM connector.

3.

Check continuity between optical sensor harness connector and BCM harness connector.

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK OPTICAL SENSOR SHORT CIRCUIT

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-90, "Removal and Installation"

 (with Intelligent Key) or 

BCS-157,

"Removal and Installation"

 (without Intelligent Key).

NO

>> Repair or replace harness.

6.

CHECK OPTICAL SENSOR GROUND OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect optical sensor connector and BCM connector.

3.

Check continuity between optical sensor harness connector and BCM harness connector.

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-90, "Removal and Installation"

 (with Intelligent Key) or 

BCS-157,

"Removal and Installation"

 (without Intelligent Key).

(+)

(

−

)

Condition

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

2

Ground

Optical sensor

When illuminating

3.1 V or more *

When shutting off light

0.6 V or less

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

1

M65*

1

M68*

2

17

Existed

Optical sensor

Ground

Continuity

Connector

Terminal

M84

1

Not existed

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

3

M65*

1

M68*

2

18

Existed

Revision: 2013 October

2014 JUKE

OPTICAL SENSOR

EXL-73

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

NO

>> Repair or replace harness.

7.

CHECK OPTICAL SENSOR SIGNAL OPEN CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect optical sensor connector and BCM connector.

3.

Check continuity between optical sensor harness connector and BCM harness connector.

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace harness.

8.

CHECK OPTICAL SENSOR SHORT CIRCUIT

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-90, "Removal and Installation"

 (with Intelligent Key) or 

BCS-157,

"Removal and Installation"

 (without Intelligent Key).

NO

>> Repair or replace harness.

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

2

M65*

1

M68*

2

14

Existed

Optical sensor

Ground

Continuity

Connector

Terminal

M84

2

Not existed

Revision: 2013 October

2014 JUKE

EXL-74

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

FRONT FOG LAMP CIRCUIT

FRONT FOG LAMP CIRCUIT

Component Function Check

INFOID:0000000009754517

1.

CHECK FRONT FOG LAMP OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the front fog lamp is turned ON.

Is the measurement normal?

YES

>> Front fog lamp circuit is normal.

NO

>> Refer to 

EXL-74, "Diagnosis Procedure"

. 

Diagnosis Procedure

INFOID:0000000009754518

1.

CHECK FRONT FOG LAMP FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK FRONT FOG LAMP SHORT CIRCUIT

1.

Disconnect front fog connector and IPDM E/R connector.

2.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)

NO

>> Repair or replace harness. And then replace the fuse.

3.

CHECK FRONT FOG LAMP BULB

Check the applicable lamp bulb.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace bulb.

4.

CHECK FRONT FOG LAMP OUTPUT VOLTAGE

CONSULT ACTIVE TEST

1.

Disconnect front fog lamp connector.

2.

Turn ignition switch ON.

3.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4.

With operating the test items, check the voltage between IPDM E/R harness connector and ground.

Fog

: Front fog lamp ON

Off

: Front fog lamp OFF

Unit

Location

Fuse No.

Capacity

Front fog lamp

IPDM E/R

#50

15 A

IPDM E/R

Ground

Continuity

Connector

Terminal

RH

E12

19

Not existed

LH

20

Revision: 2013 October

2014 JUKE

FRONT FOG LAMP CIRCUIT

EXL-75

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace IPDM E/R.

5.

CHECK FRONT FOG LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and front fog lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT

Check continuity between front fog lamp harness connector and ground.

Is the inspection result normal?

YES

>> Refer to 

GI-46, "Intermittent Incident"

.

NO

>> Repair or replace harness.

(+)

(

−

)

Test item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

RH

E12

19

Ground

EXTERNAL 
LAMPS

Fog

Battery voltage

Off

0 V

LH

20

Fog

Battery voltage

Off

0 V

IPDM E/R

Front fog lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E12

19

E48

1

Existed

LH

20

E30

Front fog lamp

Ground

Continuity

Connector

Terminal

RH

E48

2

Existed

LH

E30

Revision: 2013 October

2014 JUKE

EXL-76

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

TURN SIGNAL LAMP CIRCUIT

TURN SIGNAL LAMP CIRCUIT

Component Function Check

INFOID:0000000009754519

1.

CHECK TURN SIGNAL LAMP

CONSULT ACTIVE TEST

1.

Select “FLASHER” of BCM (FLASHER) active test item.

2.

With operating the test items, check that the turn signal lamps is turned ON.

Is the inspection result normal?

YES

>> Turn signal lamp circuit is normal.

NO

>> Refer to 

EXL-76, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009754520

1.

CHECK TURN SIGNAL LAMP BULB

Check the applicable lamp bulb.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace bulb.

2.

CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

1.

Turn ignition switch OFF.

2.

Disconnect front turn signal lamp connector, side turn signal lamp connector and rear combination lamp
connector.

3.

Turn ignition switch ON.

4.

With operating the turn signal switch, check voltage between BCM harness connector and ground.

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

LH

: Turn signal lamps (LH) ON

RH

: Turn signal lamps (RH) ON

Off

: Turn signal lamps OFF

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

B9*

1

M69*

2

49*

1

60*

2

Ground

Turn signal 
switch

LH

OFF

0 V

48*

1

61*

2

RH

OFF

0 V

PKID0926E

PKID0926E

Revision: 2013 October

2014 JUKE

TURN SIGNAL LAMP CIRCUIT

EXL-77

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 4.

3.

CHECK TURN SIGNAL LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector.

3.

Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp harness connector.

Front turn signal lamp

Side turn signal lamp

Rear turn signal lamp

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

4.

CHECK TURN SIGNAL LAMP SHORT CIRCUIT

Check continuity between BCM harness connector and ground.

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

Is the inspection result normal?

BCM

Front turn signal lamp

Continuity

Connector

Terminal

Connector

Terminal

 RH

B9*

1

M69*

2

48*

1

61*

2

E46

1

Existed

 LH

49*

1

60*

2

E27

BCM

Side turn signal lamp

Continuity

Connector

Terminal

Connector

Terminal

 RH

B9*

1

M69*

2

48*

1

61*

2

E40

1

Existed

 LH

49*

1

60*

2

E23

BCM

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

B9*

1

M69*

2

48*

1

61*

2

B59

5

Existed

LH

49*

1

60*

2

B80

BCM

Ground

Continuity

Connector

Terminal

RH

B9

*1

M69

*2

48*

1

61*

2

Not existed

LH

49*

1

60*

2

Revision: 2013 October

2014 JUKE

EXL-78

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

TURN SIGNAL LAMP CIRCUIT

YES

>> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer

to 

BCS-90, "Removal and Installation"

 (with Intelligent Key), 

BCS-157, "Removal and Installation"

(without Intelligent Key).

NO

>> Repair or replace harness.

5.

CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT

Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.

Front turn signal lamp

Side turn signal lamp

Rear turn signal lamp

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

Front turn signal lamp

Ground

Continuity

Connector

Terminal

RH

E46

2

Existed

LH

E27

Side turn signal lamp

Ground

Continuity

Connector

Terminal

RH

E40

2

Existed

LH

E23

Rear combination lamp

Ground

Continuity

Connector

Terminal

RH

B59

3

Existed

LH

B80

Revision: 2013 October

2014 JUKE

HAZARD SWITCH

EXL-79

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

HAZARD SWITCH

Component Function Check

INFOID:0000000009754521

1.

CHECK HAZARD SWITCH SIGNAL BY CONSULT

CONSULT DATA MONITOR

1.

Turn the ignition switch ON.

2.

Select “HAZARD SW” of BCM (FLASHER) data monitor item.

3.

With operating the hazard switch, check the monitor status.

Is the inspection result normal?

YES

>> Hazard switch circuit is normal.

NO

>> Refer to 

EXL-79, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009754522

1.

CHECK HAZARD SWITCH SIGNAL INPUT

1.

Turn ignition switch OFF.

2.

Disconnect hazard switch connector.

3.

Check voltage between hazard switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between hazard switch harness connector and BCM harness connector.

*1: Without Intelligent Key

*2: With Intelligent Key

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

Monitor item

Condition

Monitor status

HAZARD SW

Hazard switch

ON

On

OFF

Off

(+)

(

−

)

Voltage (Approx.)

Hazard switch

Connector

Terminal

M45

2

Ground

12 V

Hazard switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M45

2

M65

*1

M68

*2

29

Existed

Hazard switch

Ground

Continuity

Connector

Terminal

M45

2

Not existed

Revision: 2013 October

2014 JUKE

EXL-80

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

HAZARD SWITCH

YES

>> Replace BCM. Refer to 

BCS-90, "Removal and Installation"

 (With Intelligent Key) or 

BCS-157,

"Removal and Installation"

 (Without Intelligent Key).

NO

>> Repair or replace harness.

4.

CHECK HAZARD SWITCH GROUND OPEN CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace hazard switch.

NO

>> Repair or replace harness.

Hazard switch

Ground

Continuity

Connector

Terminal

M45

1

Existed

Revision: 2013 October

2014 JUKE

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-81

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

WITHOUT DAYTIME RUNNING LIGHT SYSTEM

WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table

INFOID:0000000009754523

NOTE:
Perform the self-diagnosis with CONSULT before symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp (HI) is not 
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and 

headlamp

• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-52, "Component 

Function Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-88, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]

Combination meter

• Combination meter 

Data monitor “HI-BEAM IND”

• BCM (HEADLAMP)

Active test “HEADLAMP”

Headlamp (LO) is not 
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and 

headlamp

• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-54, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM : 
Component Function Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-89, "Diagnosis Procedure"

.

Headlamp is not turned 
OFF.

When ignition switch 
is turned ON.

When ignition switch 
is turned OFF.

IPDM E/R

—

Headlamp HI and LO are not turned ON.

• Halogen bulb
• Harness between headlamp and 

ground

Headlamp ground circuit
Refer to 

EXL-59, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM : 
Diagnosis Procedure"

.

Headlamp is not turned ON/OFF with the lighting 
switch AUTO.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-88, "Symptom Table"

.

• Optical sensor
• Harness between optical sensor 

and BCM

• BCM

Optical sensor
Refer to 

EXL-71, "Component 

Function Check"

.

Front fog lamp is not 
turned ON.

One side

• Front fog lamp bulb
• Harness between IPDM E/R and 

front fog lamp

• IPDM E/R

Front fog lamp circuit
Refer to 

EXL-74, "Component 

Function Check"

.

Both side

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-91, "Diagnosis Procedure"

.

Parking lamp is not turned ON.

• Parking lamp bulb
• Harness between IPDM E/R and 

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-65, "Component 

Function Check"

.

Revision: 2013 October

2014 JUKE

EXL-82

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

WITH DAYTIME RUNNING LIGHT SYSTEM

WITH DAYTIME RUNNING LIGHT SYSTEM : Symptom Table

INFOID:0000000009754524

EXCEPT FOR NISMO MODELS

NOTE:
Perform the self-diagnosis with CONSULT before symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.

Front side marker lamp is not turned ON.

• Front side marker lamp bulb
• Harness between IPDM E/R and 

front side marker lamp

Front side marker lamp circuit
Refer to 

EXL-67, "Component 

Function Check"

.

Parking lamp and front side marker lamp are not 
turned ON.

• Harness between IPDM E/R and 

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-65, "Component 

Function Check"

.

Tail lamp is not turned ON.

• Tail lamp bulb
• Harness between IPDM E/R and 

rear combination lamp

Tail lamp circuit
Refer to 

EXL-68, "Component 

Function Check"

.

License plate lamp is not turned ON.

• License plate lamp bulb
• Harness between IPDM E/R and 

license plate lamp

License plate lamp circuit
Refer to 

EXL-70, "Component 

Function Check"

.

Tail lamp and license plate lamp are not turned 
ON.

Harness between IPDM E/R and 
rear combination lamp

Tail lamp circuit
Refer to 

EXL-68, "Component 

Function Check"

.

• Parking lamp, front side marker lamp, tail lamp 

and license plate lamp are not turned ON.

• Parking lamp, front side marker lamp, tail lamp 

and license plate lamp are not turned OFF.

Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE 
NOT TURNED ON”
Refer to 

EXL-90, "Diagnosis Procedure"

.

Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEADLAMP)

Active test “TAIL LAMP”

Turn signal lamp does 
not blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher 
activation.)

• Harness between BCM and each 

turn signal lamp

• Turn signal lamp bulb

Turn signal lamp circuit
Refer to 

EXL-76, "Component 

Function Check"

.

Indicator lamp is in-
cluded.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-88, "Symptom Table"

.

Turn signal indicator 
lamp does not blink.
(Turn signal indicator 
lamp is normal.)

One side

Combination meter

—

Both sides
(Always)

• Turn signal indicator lamp signal
- BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with the ignition switch 
OFF.)

• Combination meter power supply 

and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-50, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard switch 

and BCM

• BCM

Hazard switch
Refer to 

EXL-79, "Component 

Function Check"

.

Symptom

Possible cause

Inspection item

Revision: 2013 October

2014 JUKE

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-83

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Symptom

Possible cause

Inspection item

Headlamp (HI) is not 
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and 

headlamp

• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-52, "Component 

Function Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-88, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]

Combination meter

• Combination meter 

Data monitor “HI-BEAM IND”

• BCM (HEADLAMP)

Active test “HEADLAMP”

Headlamp (LO) is not 
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and 

daytime running light relay 1

• Harness between daytime run-

ning light relay 1 and headlamp

• Daytime running light relay 1
• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-55, "WITH DAYTIME 

RUNNING LIGHT SYSTEM : Com-
ponent Function Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-89, "Diagnosis Procedure"

.

Headlamp is not turned 
OFF.

When ignition switch 
is turned ON.

When ignition switch 
is turned OFF.

IPDM E/R

—

Headlamp HI and LO are not turned ON.

• Halogen bulb
• Harness between headlamp and 

daytime running light relay 2

• Harness between daytime run-

ning light relay 2 and ground

• Daytime running light relay 2

Headlamp ground circuit
Refer to 

EXL-59, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM : 
Diagnosis Procedure"

.

Daytime running light is not turned ON.
[Headlamp (HI) is turned ON.]

• Fuse
• Harness between IPDM E/R and 

daytime running light relay 2

• Daytime running light relay 2
• IPDM E/R
• BCM
• ECM
• Combination meter

• Daytime running light relay circuit

Refer to 

EXL-61, "Component 

Function Check"

.

• BCM (HEADLAMP)

Data monitor “ENGINE STATE”

• Combination mete

Data monitor “PKB SW”

• BCM (HEADLAMP)

Active test “DAYTIME RUNNING 
LIGHT”

Headlamps (both HI and LO) turn ON in the dim-
ming status while daytime running light system is 
ON.

Daytime running light relay 1

Daytime running light relay 1
Refer to 

EXL-58, "WITH DAYTIME 

RUNNING LIGHT SYSTEM : Com-
ponent Inspection"

.

Front fog lamp is not 
turned ON.

One side

• Front fog lamp bulb
• Harness between IPDM E/R and 

front fog lamp

• IPDM E/R

Front fog lamp circuit
Refer to 

EXL-74, "Component 

Function Check"

.

Both side

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-91, "Diagnosis Procedure"

.

Parking lamp is not turned ON.

• Parking lamp bulb
• Harness between IPDM E/R and 

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-65, "Component 

Function Check"

.

Revision: 2013 October

2014 JUKE

EXL-84

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

FOR NISMO MODELS

NOTE:
Perform the self-diagnosis with CONSULT before symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.

Front side marker lamp is not turned ON.

• Front side marker lamp bulb
• Harness between IPDM E/R and 

front side marker lamp

Front side marker lamp circuit
Refer to 

EXL-67, "Component 

Function Check"

.

Parking lamp and front side marker lamp are not 
turned ON.

• Harness between IPDM E/R and 

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-65, "Component 

Function Check"

.

Tail lamp is not turned ON.

• Tail lamp bulb
• Harness between IPDM E/R and 

rear combination lamp

Tail lamp circuit
Refer to 

EXL-68, "Component 

Function Check"

.

License plate lamp is not turned ON.

• License plate lamp bulb
• Harness between IPDM E/R and 

license plate lamp

License plate lamp circuit
Refer to 

EXL-70, "Component 

Function Check"

.

Tail lamp and license plate lamp are not turned 
ON.

Harness between IPDM E/R and 
rear combination lamp

Tail lamp circuit
Refer to 

EXL-68, "Component 

Function Check"

.

• Parking lamp, front side marker lamp, tail lamp 

and license plate lamp are not turned ON.

• Parking lamp, front side marker lamp, tail lamp 

and license plate lamp are not turned OFF.

Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE 
NOT TURNED ON”
Refer to 

EXL-90, "Diagnosis Procedure"

.

Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEADLAMP)

Active test “TAIL LAMP”

Turn signal lamp does 
not blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher 
activation.)

• Harness between BCM and each 

turn signal lamp

• Turn signal lamp bulb

Turn signal lamp circuit
Refer to 

EXL-76, "Component 

Function Check"

.

Indicator lamp is in-
cluded.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-88, "Symptom Table"

.

Turn signal indicator 
lamp does not blink.
(Turn signal indicator 
lamp is normal.)

One side

Combination meter

—

Both sides
(Always)

• Turn signal indicator lamp signal
- BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with the ignition switch 
OFF.)

• Combination meter power supply 

and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-50, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard switch 

and BCM

• BCM

Hazard switch
Refer to 

EXL-79, "Component 

Function Check"

.

Symptom

Possible cause

Inspection item

Revision: 2013 October

2014 JUKE

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-85

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Symptom

Possible cause

Inspection item

Headlamp (HI) is not 
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and 

headlamp

• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-52, "Component 

Function Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-88, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]

Combination meter

• Combination meter 

Data monitor “HI-BEAM IND”

• BCM (HEADLAMP)

Active test “HEADLAMP”

Headlamp (LO) is not 
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and 

headlamp

• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-54, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM : 
Component Function Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-89, "Diagnosis Procedure"

.

Headlamp is not turned 
OFF.

When ignition switch 
is turned ON.

When ignition switch 
is turned OFF.

IPDM E/R

—

Headlamp HI and LO are not turned ON.

• Halogen bulb
• Harness between headlamp and 

ground

Headlamp ground circuit
Refer to 

EXL-59, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM : 
Diagnosis Procedure"

.

Daytime running light is not turned ON.

• Fuse
• Daytime running light
• Harness between IPDM E/R and 

daytime running light

• IPDM E/R

Daytime running light circuit
Refer to 

EXL-63, "Component 

Function Check"

.

Parking lamp is not turned ON.

• Parking lamp bulb
• Harness between IPDM E/R and 

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-65, "Component 

Function Check"

.

Front side marker lamp is not turned ON.

• Front side marker lamp bulb
• Harness between IPDM E/R and 

front side marker lamp

Front side marker lamp circuit
Refer to 

EXL-67, "Component 

Function Check"

.

Parking lamp and front side marker lamp are not 
turned ON.

• Harness between IPDM E/R and 

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-65, "Component 

Function Check"

.

Tail lamp is not turned ON.

• Tail lamp bulb
• Harness between IPDM E/R and 

rear combination lamp

Tail lamp circuit
Refer to 

EXL-68, "Component 

Function Check"

.

License plate lamp is not turned ON.

• License plate lamp bulb
• Harness between IPDM E/R and 

license plate lamp

License plate lamp circuit
Refer to 

EXL-70, "Component 

Function Check"

.

Tail lamp and license plate lamp are not turned 
ON.

Harness between IPDM E/R and 
rear combination lamp

Tail lamp circuit
Refer to 

EXL-68, "Component 

Function Check"

.

• Parking lamp, front side marker lamp, tail lamp 

and license plate lamp are not turned ON.

• Parking lamp, front side marker lamp, tail lamp 

and license plate lamp are not turned OFF.

Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE 
NOT TURNED ON”
Refer to 

EXL-90, "Diagnosis Procedure"

.

Revision: 2013 October

2014 JUKE

EXL-86

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEADLAMP)

Active test “TAIL LAMP”

Turn signal lamp does 
not blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher 
activation.)

• Harness between BCM and each 

turn signal lamp

• Turn signal lamp bulb

Turn signal lamp circuit
Refer to 

EXL-76, "Component 

Function Check"

.

Indicator lamp is in-
cluded.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-88, "Symptom Table"

.

Turn signal indicator 
lamp does not blink.
(Turn signal indicator 
lamp is normal.)

One side

Combination meter

—

Both sides
(Always)

• Turn signal indicator lamp signal
- BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with the ignition switch 
OFF.)

• Combination meter power supply 

and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-50, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard switch 

and BCM

• BCM

Hazard switch
Refer to 

EXL-79, "Component 

Function Check"

.

Symptom

Possible cause

Inspection item

Revision: 2013 October

2014 JUKE

NORMAL OPERATING CONDITION

EXL-87

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

NORMAL OPERATING CONDITION

Description

INFOID:0000000009754525

AUTO LIGHT SYSTEM

The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes the control difference. This is
normal.

Revision: 2013 October

2014 JUKE