Nissan Juke (2014 year). Service Repair Manual - part 127

EXL-56

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

HEADLAMP (LO) CIRCUIT

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 8.

3.

CHECK HEADLAMP LO (RH) OPEN CIRCUIT -1

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and daytime running light relay 1 harness con-
nector.

4.

Check continuity between daytime running light relay 1 harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK HEADLAMP LO (RH) OPEN CIRCUIT-2

1.

Disconnect headlamp connector.

2.

Check continuity between daytime running light relay 1 harness connector and headlamp harness con-
nector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK DAYTIME RUNNING LIGHT RELAY 1

Check daytime running light relay 1. Refer to 

EXL-58, "WITH DAYTIME RUNNING LIGHT SYSTEM : Compo-

nent Inspection"

.

Is the inspection result normal?

YES

>> Replace headlamp bulb RH.

NO

>> Replace daytime running light relay 1.

6.

CHECK HEADLAMP LO (LH) OUTPUT VOLTAGE

CONSULT ACTIVE TEST

1.

Turn ignition switch OFF.

2.

Disconnect headlamp LH connector.

3.

Turn ignition switch ON.

4.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

(+)

(

−

)

Test item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E15

52

Ground

EXTERNAL LAMPS

Lo

Battery voltage

Off

0 V

IPDM E/R

Daytime running light relay 1

Continuity

Connector

Terminal

Connector

Terminal

E15

52

E64

2

Existed

5

Daytime running light relay 1

Ground

Continuity

Terminal

Connector

E64

1

Existed

Daytime running light relay 1

Headlamp RH

Continuity

Connector

Terminal

Connector

Terminal

E64

3

E45

1

Existed

Revision: 2013 October

2014 JUKE

HEADLAMP (LO) CIRCUIT

EXL-57

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

5.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> GO TO 12.

7.

CHECK HEADLAMP LO (LH) OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and headlamp LH harness connector.

Is the inspection result normal?

YES

>> Replace headlamp bulb LH.

NO

>> Repair or replace harness.

8.

CHECK HEADLAMP LO (RH) FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuses are not fusing.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> GO TO 9.

9.

CHECK HEADLAMP LO (RH) SHORT CIRCUIT- 1

1.

Disconnect IPDM E/R connector.

2.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace harness. And then replace the fuse.

10.

CHECK DAYTIME RUNNING LIGHT RELAY 1

Check daytime running light relay 1. Refer to 

EXL-58, "WITH DAYTIME RUNNING LIGHT SYSTEM : Compo-

nent Inspection"

.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Replace daytime running light relay 1.

11.

CHECK HEADLAMP LO (RH) SHORT CIRCUIT-2

1.

Disconnect headlamp RH connector.

2.

Check continuity between Daytime running light relay 1 harness connector and ground.

(+)

(

−

)

Test item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E15

51

Ground

EXTERNAL LAMPS

Lo

Battery voltage

Off

0 V

IPDM E/R

Headlamp LH

Continuity

Connector

Terminal

Connector

Terminal

E15

51

E26

1

Existed

Unit

Location

Fuse No.

Capacity

Headlamp LO (RH) 

IPDM E/R

#54

15 A

IPDM E/R

Ground

Continuity

Connector

Terminal

E15

52

Not existed

Revision: 2013 October

2014 JUKE

EXL-58

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

HEADLAMP (LO) CIRCUIT

Is the inspection result normal?

YES

>> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)

NO

>> Repair or replace harness. And then replace the fuse.

12.

CHECK HEADLAMP LO (LH) FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuses are not fusing.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> GO TO 13.

13.

CHECK HEADLAMP LO (LH) SHORT CIRCUIT

1.

Disconnect IPDM E/R connector.

2.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)

NO

>> Repair or replace harness. And then replace the fuse.

WITH DAYTIME RUNNING LIGHT SYSTEM : Component Inspection

INFOID:0000000009754499

1.

CHECK DAYTIME RUNNING LIGHT RELAY 1

1.

Turn the ignition switch OFF.

2.

Remove daytime running light relay 1.

3.

Check continuity between daytime running light relay 1 terminals.

4.

Apply battery voltage to daytime running light relay 1 between terminals 1 and 2.

5.

Check continuity between daytime running light relay 1 terminals.

Is the inspection result normal?

YES

>> Daytime running light relay 1 is normal.

NO

>> Replace Daytime running light relay- 1.

Daytime running light relay 1

Ground

Continuity

Connector

Terminal

E64

3

Not existed

Unit

Location

Fuse No.

Capacity

Headlamp LO (LH) 

IPDM E/R

#53

15 A

IPDM E/R

Ground

Continuity

Connector

Terminal

E15

51

Not existed

Daytime running light relay 1

Continuity

Terminal

3

1

Not existed

5

Daytime running light relay 1

Condition

Continuity

Terminal

3

5

Voltage

Apply

Existed

Not Apply

Not existed

Revision: 2013 October

2014 JUKE

HEADLAMP GROUND CIRCUIT

EXL-59

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

HEADLAMP GROUND CIRCUIT

WITHOUT DAYTIME RUNNING LIGHT SYSTEM

WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure

INFOID:0000000009754500

1.

CHECK HEADLAMP GROUND OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect headlamp connector.

3.

Check continuity between headlamp harness connector and ground.

Is the inspection result normal?

YES

>> Headlamp ground circuit is normal.

NO

>> Repair or replace harness.

WITH DAYTIME RUNNING LIGHT SYSTEM

WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure

INFOID:0000000009754501

1.

CHECK ILLUMINATION STATUS OF HEADLAMPS

Check illumination status of headlamps.

Which headlamp does not turn ON?

RH

>> GO TO 2.

LH

>> GO TO 4.

2.

CHECK HEADLAMP LO (RH) GROUND OPEN CIRCUIT-1

1.

Turn ignition switch OFF.

2.

Disconnect headlamp RH connector.

3.

Remove daytime running light relay 2.

4.

Check continuity between daytime running light relay 2 harness connector and headlamp RH harness
connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK HEADLAMP LO (RH) GROUND OPEN CIRCUIT-2

Check continuity between daytime running light relay 2 harness connector and ground.

Is the inspection result normal?

YES

>> Headlamp RH ground circuit is normal.

NO

>> Repair or replace harness.

4.

CHECK HEADLAMP LO (LH) GROUND OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect headlamp LH connector.

Headlamp

Ground

Continuity

Connector

Terminal

RH

E45

2

Existed

LH

E26

Daytime running light relay 2

Headlamp RH

Continuity

Connector

Terminal

Connector

Terminal

E65

3

E45

2

Existed

Daytime running light relay 2

Ground

Continuity

Connector

Terminal

E65

4

Existed

Revision: 2013 October

2014 JUKE

EXL-60

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

HEADLAMP GROUND CIRCUIT

3.

Check continuity between headlamp LH harness connector and ground.

Is the inspection result normal?

YES

>> Headlamp LH ground circuit is normal.

NO

>> Repair or replace harness.

Headlamp LH

Ground

Continuity

Connector

Terminal

E26

2

Existed

Revision: 2013 October

2014 JUKE

DAYTIME RUNNING LIGHT RELAY CIRCUIT

EXL-61

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DAYTIME RUNNING LIGHT RELAY CIRCUIT

Component Function Check

INFOID:0000000009754502

1.

CHECK DAYTIME RUNNING LIGHT OPERATION

CONSULT ACTIVE TEST

1.

Select “DAYTIME RUNNING LIGHT” of BCM (HEADLAMP) active test item.

2.

With operating the test items, check that daytime running light operation.

Is the inspection result normal?

YES

>> Daytime running light relay circuit is normal.

NO

>> Refer to 

EXL-61, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009754503

1.

CHECK DAYTIME RUNNING LIGHT RELAY 2 FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the fuse after repairing the applicable circuit.

2.

CHECK DAYTIME RUNNING LIGHT RELAY 2 POWER SUPPLY

1.

Remove daytime running light relay.

2.

Check voltage between daytime running light relay 2 harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK DAYTIME RUNNING LIGHT RELAY 2

Check daytime running light relay 2. Refer to 

EXL-62, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace daytime running light relay 2.

4.

CHECK DAYTIME RUNNING LIGHT RELAY 2 CONTROL SIGNAL OUTPUT

CONSULT ACTIVE TEST

1.

Install daytime running light relay 2.

2.

Turn ignition switch ON.

3.

Select “DAYTIME RUNNING LIGHT” of BCM (HEADLAMP) active test item.

4.

With operating the test item, check voltage between IPDM E/R harness connector and ground.

On

: Daytime running light ON

Off

: Daytime running light OFF

Unit

Fuse No.

Capacity

Daytime running light relay 2

#24

10 A

(+)

(

−

)

Voltage

(Approx.)

Daytime running light relay 2

Connector

Terminal

E65

1

Ground

Battery voltage

5

Revision: 2013 October

2014 JUKE

EXL-62

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

DAYTIME RUNNING LIGHT RELAY CIRCUIT

Is the inspection result normal?

YES

>> Daytime running light relay 2 circuit is OK.

NO-1 (Fixed at 0 V)>>GO TO 5.
NO-2 (Fixed at battery voltage) >>Replace IPDM E/R.

5.

CHECK DAYTIME RUNNING LIGHT RELAY 2 CONTROL SIGNAL OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Remove daytime running light relay 2.

3.

Disconnect IPDM E/R harness connector.

4.

Check continuity between IPDM E/R harness connector and daytime running light relay 2 harness con-
nector.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK DAYTIME RUNNING LIGHT RELAY 2 CONTROL SIGNAL SHORT CIRCUIT

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace harness.

Component Inspection

INFOID:0000000009754504

1.

CHECK DAYTIME RUNNING LIGHT RELAY 2

1.

Turn the ignition switch OFF.

2.

Remove daytime running light relay 2.

3.

Apply battery voltage to daytime running light relay- between terminals 1 and 2.

4.

Check continuity between daytime running light relay 2 terminals.

Is the inspection result normal?

YES

>> Daytime running light relay 2 is normal.

NO

>> Replace daytime running light relay 2.

(+)

(

−

)

Test item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E13

28

Ground

DAYTIME RUN-
NING LIGHT

On

0 V

Off

Battery voltage

IPDM E/R

Daytime running light relay 2

Continuity

Connector

Terminal

Connector

Terminal

E13

28

E65

2

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E13

28

Not existed

Daytime running light relay-2

Condition

Continuity

Terminal

5

3

Voltage

Apply

Existed

Not Apply

Not existed

4

Apply

Not existed

Not Apply

Existed

Revision: 2013 October

2014 JUKE

DAYTIME RUNNING LIGHT CIRCUIT

EXL-63

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DAYTIME RUNNING LIGHT CIRCUIT

Component Function Check

INFOID:0000000009754505

1.

CHECK DAYTIME RUNNING LIGHT OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the daytime running light is turned ON.

Is the measurement normal?

YES

>> Daytime running light circuit is normal.

NO

>> Refer to 

EXL-63, "Diagnosis Procedure"

. 

Diagnosis Procedure

INFOID:0000000009754506

1.

CHECK DAYTIME RUNNING LIGHT FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DAYTIME RUNNING LIGHT SHORT CIRCUIT

1.

Disconnect daytime running light connector and IPDM E/R connector.

2.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)

NO

>> Repair or replace harness. And then replace the fuse.

3.

CHECK DAYTIME RUNNING LIGHT OUTPUT VOLTAGE

CONSULT ACTIVE TEST

1.

Disconnect daytime running light connector.

2.

Turn ignition switch ON.

3.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4.

With operating the test items, check the voltage between IPDM E/R harness connector and ground.

Fog

: Daytime running light ON

Off

: Daytime running light OFF

Unit

Location

Fuse No.

Capacity

Daytime running light

IPDM E/R

#50

15 A

IPDM E/R

Ground

Continuity

Connector

Terminal

RH

E12

19

Not existed

LH

20

(+)

(

−

)

Test item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

RH

E12

19

Ground

EXTERNAL 
LAMPS

Fog

Battery voltage

Off

0 V

LH

20

Fog

Battery voltage

Off

0 V

Revision: 2013 October

2014 JUKE

EXL-64

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

DAYTIME RUNNING LIGHT CIRCUIT

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace IPDM E/R.

4.

CHECK DAYTIME RUNNING LIGHT OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and daytime running light harness connector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK DAYTIME RUNNING LIGHT GROUND CIRCUIT OPEN CIRCUIT

Check continuity between daytime running light harness connector and ground.

Is the inspection result normal?

YES

>> Replace daytime running light. Refer to 

EXL-100, "Removal and Installation"

.

NO

>> Repair or replace harness.

IPDM E/R

Daytime running light

Continuity

Connector

Terminal

Connector

Terminal

RH

E12

19

E75

1

Existed

LH

20

E76

Daytime running light

Ground

Continuity

Connector

Terminal

RH

E75

2

Existed

LH

E76

Revision: 2013 October

2014 JUKE

PARKING LAMP CIRCUIT

EXL-65

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

PARKING LAMP CIRCUIT

Component Function Check

INFOID:0000000009754507

1.

CHECK PARKING LAMP OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the parking lamp is turned ON.

Is the inspection result normal?

YES

>> Parking lamp circuit is normal.

NO

>> Refer to 

EXL-65, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009754508

1.

CHECK PARKING LAMP FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuses are not fusing.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK PARKING LAMP SHORT CIRCUIT

1.

Disconnect the following connectors.

-

IPDM E/R

-

Parking lamp

-

Front side marker lamp

-

Rear combination lamp

-

Back door opener switch

2.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace fuse. (Replace IPDM E/R if fusing is found again.)

NO

>> Repair or replace harness. And then replace the fuse.

3.

CHECK PARKING LAMP BULB

Check applicable lamp bulb.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace bulb.

4.

CHECK PARKING LAMP OUTPUT VOLTAGE

CONSULT ACTIVE TEST

TAIL

: Parking lamp ON

Off

: Parking lamp OFF

Unit

Location

Fuse No.

Capacity

• Parking  lamp
• Front side marker lamp
• Tail lamp
• License plate lamp

IPDM E/R

#47

10 A

IPDM E/R

Ground

Continuity

Connector

Terminal

E14

43

Not existed

44

Revision: 2013 October

2014 JUKE

EXL-66

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

PARKING LAMP CIRCUIT

1.

Disconnect parking lamp connector.

2.

Turn ignition switch ON.

3.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace IPDM E/R.

5.

CHECK PARKING LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and parking lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK PARKING LAMP GROUND OPEN CIRCUIT

Check continuity between parking lamp harness connector and ground.

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

(+)

(

−

)

Test item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E14

43

Ground

EXTERNAL 
LAMPS

TAIL

Battery voltage

Off

0 V

IPDM E/R

Parking lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

43

E43

1

Existed

LH

E24

Parking lamp

Ground

Continuity

Connector

Terminal

RH

E43

2

Existed

LH

E24

Revision: 2013 October

2014 JUKE

FRONT SIDE MARKER LAMP CIRCUIT

EXL-67

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

FRONT SIDE MARKER LAMP CIRCUIT

Component Function Check

INFOID:0000000009754509

1.

CHECK PARKING LAMP OPERATION

Check that the parking lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check parking lamp circuit. Refer to 

EXL-65, "Component Function Check"

.

2.

CHECK FRONT SIDE MARKER LAMP OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the front side marker lamp is turned ON.

Is the inspection result normal?

YES

>> Front side marker lamp circuit is normal.

NO

>> Refer to 

EXL-67, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009754510

1.

CHECK FRONT SIDE MARKER LAMP BULB

Check applicable lamp bulb.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace bulb.

2.

CHECK FRONT SIDE MARKER LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector and front side marker lamp connector.

3.

Check continuity between IPDM E/R harness connector and front side marker lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK FRONT SIDE MARKER LAMP GROUND OPEN CIRCUIT

Check continuity between front side marker lamp harness connector and ground.

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

TAIL

: Front side marker lamp ON

Off

: Front side marker lamp OFF

IPDM E/R

Front side marker lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

43

E32

1

Existed

LH

E31

Front side marker lamp

Ground

Continuity

Connector

Terminal

RH

E32

2

Existed

LH

E31

Revision: 2013 October

2014 JUKE

EXL-68

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

TAIL LAMP CIRCUIT

TAIL LAMP CIRCUIT

Component Function Check

INFOID:0000000009754511

1.

CHECK PARKING LAMP AND FRONT SIDE MARKER LAMP OPERATION

Check that the parking lamp and front side marker lamp are turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check parking lamp circuit. Refer to 

EXL-65, "Component Function Check"

.

2.

CHECK TAIL LAMP OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the tail lamp is turned ON.

Is the inspection result normal?

YES

>> Tail lamp circuit is normal.

NO

>> Refer to 

EXL-68, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009754512

1.

CHECK TAIL LAMP BULB

Check the applicable lamp bulb.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace bulb.

2.

CHECK TAIL LAMP OUTPUT VOLTAGE

CONSULT ACTIVE TEST

1.

Disconnect rear combination lamp connector.

2.

Turn ignition switch ON.

3.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R.

3.

CHECK TAIL LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector and rear combination lamp connector.

3.

Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.

TAIL

: Tail Lamp ON

Off

: Tail lamp OFF

(+)

(

−

)

Test item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E14

44

Ground

EXTERNAL 
LAMPS

TAIL

Battery voltage

Off

0 V

IPDM E/R

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

44

B59

2

Existed

LH

B80

Revision: 2013 October

2014 JUKE

TAIL LAMP CIRCUIT

EXL-69

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK TAIL LAMP GROUND OPEN CIRCUIT

Check continuity between rear combination lamp harness connector and ground.

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

Rear combination lamp

Ground

Continuity

Connector

Terminal

RH

B59

3

Existed

LH

B80

Revision: 2013 October

2014 JUKE

EXL-70

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

LICENSE PLATE LAMP CIRCUIT

LICENSE PLATE LAMP CIRCUIT

Component Function Check

INFOID:0000000009754513

1.

CHECK TAIL LAMP OPERATION

Check that the tail lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check tail lamp circuit. Refer to 

EXL-68, "Component Function Check"

.

2.

CHECK LICENSE PLATE LAMP OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the lighting switch, check that the license plate lamp is turned ON.

Is the inspection result normal?

YES

>> License plate lamp circuit is normal.

NO

>> Refer to 

EXL-70, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009754514

1.

CHECK LICENSE PLATE LAMP BULB

Check the applicable lamp bulb.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace bulb.

2.

CHECK LICENSE PLATE LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector and back door opener switch connector.

3.

Check continuity between IPDM E/R harness connector and back door opener switch harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

TAIL

: License plate lamp ON

Off

: License plate lamp OFF

IPDM E/R

Back door opener switch

Continuity

Connector

Terminal

Connector

Terminal

E14

44

D107

5

Existed

Back door opener switch

Ground

Continuity

Connector

Terminal

D107

6

Existed

Revision: 2013 October

2014 JUKE

OPTICAL SENSOR

EXL-71

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

OPTICAL SENSOR

Component Function Check

INFOID:0000000009754515

1.

CHECK OPTICAL SENSOR SIGNAL BY CONSULT

CONSULT DATA MONITOR

1.

Turn ignition switch ON.

2.

Select “OPTISEN (DTCT)” of BCM (HEADLAMP) data monitor item.

3.

Turn lighting switch AUTO.

4.

With the optical sensor illuminating, check the monitor status. 

*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.

Is the inspection result normal?

YES

>> Optical sensor is normal.

NO

>> Refer to 

EXL-71, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009754516

1.

CHECK OPTICAL SENSOR POWER SUPPLY INPUT

1.

Turn ignition switch ON.

2.

Turn lighting switch AUTO.

3.

Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK OPTICAL SENSOR GROUND INPUT

Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 6.

3.

CHECK OPTICAL SENSOR SIGNAL OUTPUT

 With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.

Monitor item

Condition

Voltage (Approx.)

OPTISEN (DTCT)

Optical sensor

When illuminating

3.1 V or more *

When shutting off light

0.6 V or less

(+)

(

−

)

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

1

Ground

5 V

(+)

(

−

)

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

3

Ground

0 V

Revision: 2013 October

2014 JUKE