Nissan Juke (2014 year). Service Repair Manual - part 129

EXL-88

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

Description

INFOID:0000000009754526

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.

Diagnosis Procedure

INFOID:0000000009754527

1.

COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to 

BCS-88, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

1.

Select “HL HI REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Replace BCM. Refer to 

BCS-90, "Removal and Installation"

 (with Intelligent Key), 

BCS-157,

"Removal and Installation"

 (without Intelligent Key).

Monitor item

Condition

Monitor status

HL HI REQ

Lighting switch
(2ND)

HI or PASS

ON

LO

OFF

Revision: 2013 October

2014 JUKE

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

EXL-89

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

Description

INFOID:0000000009754528

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000009754529

1.

CHECK COMBINATION SWITCH

Check the combination switch. Refer to 

BCS-88, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

1.

Select “HL LO REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Replace BCM. Refer to 

BCS-90, "Removal and Installation"

 (with Intelligent Key), 

BCS-157,

"Removal and Installation"

 (without Intelligent Key).

Monitor item

Condition

Monitor status

HL LO REQ

Lighting switch

2ND

ON

OFF

OFF

Revision: 2013 October

2014 JUKE

EXL-90

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT 

TURNED ON

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON

Description

INFOID:0000000009754530

The parking, license plate, tail, rear side marker lamps and each illumination are not turned ON in any condi-
tion.

Diagnosis Procedure

INFOID:0000000009754531

1.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-88, "Symptom Table"

.

Is the combination switch normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

1.

Select “TAIL & CLR REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the item status normal?

YES

>> Replace IPDM E/R.

NO

>> Replace BCM. Refer to 

BCS-90, "Removal and Installation"

 (with Intelligent Key), 

BCS-157,

"Removal and Installation"

 (without Intelligent Key).

Monitor item

Condition

Monitor status

TAIL & CLR REQ

Lighting switch

1ST

ON

OFF

OFF

Revision: 2013 October

2014 JUKE

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

EXL-91

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

Description

INFOID:0000000009754532

The front fog lamps are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000009754533

1.

CHECK FUSE

Check that the following fuse is fusing.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the applicable circuit. And then replace the fuse.

2.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-88, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning part.

3.

CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

1.

Select “FR FOG REQ” of IPDM E/R data monitor item.

2.

With operating the front fog lamp switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Replace BCM. Refer to 

BCS-90, "Removal and Installation"

 (with Intelligent Key), 

BCS-157,

"Removal and Installation"

 (without Intelligent Key).

Unit

Location

Fuse No.

Capacity

Front fog lamp

Fuse and fusible link block

#50

15 A

Monitor item

Condition

Monitor status

FR FOG REQ

Front fog lamp switch
(With lighting switch 1ST)

ON

ON

OFF

OFF

Revision: 2013 October

2014 JUKE

EXL-92

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

HEADLAMP AIMING ADJUSTMENT

PERIODIC MAINTENANCE

HEADLAMP AIMING ADJUSTMENT

Description

INFOID:0000000009754534

PREPARATION BEFORE ADJUSTING

NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been

replaced.

Before performing aiming adjustment, check the following. 

• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk

room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool. 

• Wipe out dirt on the headlamp.

CAUTION:

Never use organic solvent (thinner, gasoline etc.)

• Ride alone on the driver seat.

AIMING ADJUSTMENT SCREW

JMLIA1338ZZ

A

Headlamp RH (UP/DOWN) adjustment screw B.

Headlamp LH (UP/DOWN) adjustment screw

: Vehicle center

Adjustment screw

Screw driver rotation

Facing direction

A

Headlamp RH (UP/DOWN)

Clockwise

DOWN

Counterclockwise

UP

Revision: 2013 October

2014 JUKE

HEADLAMP AIMING ADJUSTMENT

EXL-93

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Aiming Adjustment Procedure

INFOID:0000000009754535

1.

Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.

2.

Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp center and the screen.

3.

Start the engine. Turn the headlamp (LO) ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.

CAUTION:

Never cover the lens surface with a tape etc. The lens is made of resin.

4.

Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).

Low beam distribution on the screen 

5.

Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).

unit: mm (in)

Side view

B

Headlamp LH (UP/DOWN)

Clockwise

DOWN

Counterclockwise

UP

Adjustment screw

Screw driver rotation

Facing direction

Light axis measurement range (R)

: 350 

±

 175 mm (13.78 

±

 6.89 in)

JSLIA0005ZZ

Horizontal center line of headlamp (H)

Highest cutoff line height (M)

Lowest cutoff line height (N)

700 (27.56) or less

4 (0.16)

30 (1.18)

701(27.60) – 800 (31.50)

4 (0.16)

30 (1.18)

801 (31.54) or more

17 (0.67)

44 (1.73)

JSLIA0006ZZ

Distance between the headlamp center and the screen (L)

: 10 m (32.8 ft)

Revision: 2013 October

2014 JUKE

EXL-94

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

FRONT FOG LAMP AIMING ADJUSTMENT

FRONT FOG LAMP AIMING ADJUSTMENT

Description

INFOID:0000000009754536

PREPARATION BEFORE ADJUSTING

NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been

replaced.

Before performing aiming adjustment, check the following. 

• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk

room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool. 

• Wipe out dirt on the headlamp.

CAUTION:

Never use organic solvent (thinner, gasoline etc.)

• Ride alone on the driver seat.

AIMING ADJUSTMENT SCREW

• Turn the aiming adjusting screw for adjustment.

• For the position and direction of the adjusting screw, refer to the

figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.

Aiming Adjustment Procedure

INFOID:0000000009754537

1.

Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.

2.

Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.

3.

Start the engine. Turn the front fog lamp ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.

CAUTION:

Never cover the lens surface with a tape etc. The lens is made of resin.

4.

Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 150 mm (5.91 in).

A: UP

B: DOWN

JMLIA1249ZZ

Revision: 2013 October

2014 JUKE

FRONT FOG LAMP AIMING ADJUSTMENT

EXL-95

< PERIODIC MAINTENANCE >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Front fog lamp light distribution on the screen 

JPLIA0008ZZ

A

: Cutoff line

B

: High illuminance area

H

: Horizontal center line of front fog lamp

V

: Vertical center line of front fog lamp

X

: Cutoff line height

Revision: 2013 October

2014 JUKE

EXL-96

< REMOVAL AND INSTALLATION >

[HALOGEN TYPE]

HEADLAMP

REMOVAL AND INSTALLATION

HEADLAMP

Exploded View

INFOID:0000000009754538

REMOVAL

DISASSEMBLY

Removal and Installation

INFOID:0000000009754539

CAUTION:

Disconnect the battery negative terminal or the fuse.

REMOVAL

1.

Headlamp assembly

: N·m (kg-m, in-lb)

JMLIA1768GB

1.

Headlamp housing assembly

2.

Cap

3.

Halogen bulb

4.

Bulb holder

JMLIA1317ZZ

Revision: 2013 October

2014 JUKE

HEADLAMP

EXL-97

< REMOVAL AND INSTALLATION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

1.

Remove front bumper fascia. Refer to 

EXT-15, "Removal and Installation"

.

2.

Remove headlamp mounting bolts.

3.

Pull out the headlamp assembly forward the vehicle, and then disconnect the connector before removing
the headlamp assembly.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

After installation, perform aiming adjustment. Refer to

EXL-92, "Description"

.

Replacement

INFOID:0000000009754540

CAUTION:

• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

HEADLAMP BULB

1.

Disconnect headlamp bulb connector.

2.

Remove bulb holder.

3.

Remove halogen bulb from the headlamp housing assembly.

Disassembly and Assembly

INFOID:0000000009754541

DISASSEMBLY

1.

Remove back cover.

2.

Remove bulb holder.

3.

Remove halogen bulb from the headlamp housing assembly.

ASSEMBLY

Note the following item, and then assemble in the reverse order of disassembly.

CAUTION:

After installing the bulb, install the resin cap and the bulb socket securely for watertightness.

Revision: 2013 October

2014 JUKE

EXL-98

< REMOVAL AND INSTALLATION >

[HALOGEN TYPE]

FRONT COMBINATION LAMP

FRONT COMBINATION LAMP

Exploded View

INFOID:0000000009754542

REMOVAL

DISASSEMBLY

Removal and Installation

INFOID:0000000009754543

CAUTION:

Disconnect the battery negative terminal or remove the fuse.

REMOVAL

1.

Front combination lamp

: N·m (kg-m, in-lb)

JMLIA1236ZZ

1.

Parking lamp bulb

2.

Parking lamp bulb socket

3.

Front marker lamp bulb socket

4.

Front marker lamp bulb

5.

Front turn signal lamp bulb socket

6.

Front turn signal lamp bulb

7.

Front combination lamp housing

JMLIA1318ZZ

Revision: 2013 October

2014 JUKE

FRONT COMBINATION LAMP

EXL-99

< REMOVAL AND INSTALLATION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

1.

Remove front bumper fascia. Refer to 

EXT-15, "Removal and Installation"

.

2.

Remove front combination lamp mounting bolts and nut.

3.

Pull out front combination lamp assembly forward the vehicle, and then disconnect the connector before
removing the headlamp assembly.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

Interference of front combination lamp lens with front fender may cause intrusion of water into front
combination lamp or rusting of fender due to damage of painted surface. Be careful to operate without
allowing parts to interfere with each other.

Replacement

INFOID:0000000009754544

CAUTION:

• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

PARKING LAMP BULB

1.

Rotate the parking lamp bulb socket counterclockwise and unlock it.

2.

Remove parking lamp bulb from the bulb socket.

FRONT MARKER LAMP BULB

1.

Rotate the front marker lamp bulb socket counterclockwise and unlock it.

2.

Remove the front marker lamp bulb from the bulb socket.

FRONT TURN SIGNAL LAMP BULB

1.

Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.

2.

Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.

Disassembly and Assembly

INFOID:0000000009754545

DISASSEMBLY

1.

Rotate the parking lamp bulb socket counterclockwise and unlock it.

2.

Remove parking lamp bulb from the bulb socket.

3.

Rotate the front marker lamp bulb socket counterclockwise and unlock it.

4.

Remove the front marker lamp bulb from the bulb socket.

5.

Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.

6.

Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.

ASSEMBLY

Note the following item and then, install in the reverse order of removal.

CAUTION:

After installing the bulb, install the resin cap and the bulb socket securely for watertightness.

Revision: 2013 October

2014 JUKE

EXL-100

< REMOVAL AND INSTALLATION >

[HALOGEN TYPE]

DAYTIME RUNNING LIGHT

DAYTIME RUNNING LIGHT

Exploded View

INFOID:0000000009754546

Removal and Installation

INFOID:0000000009754547

CAUTION:

Disconnect the battery negative terminal or remove the fuse to prevent electric leakage.

REMOVAL

1.

Remove front bumper fascia lower. Refer to 

EXT-15, "Removal and Installation"

.

2.

Disconnect daytime running light harness connector.

3.

Remove daytime running light mounting nuts.

4.

Remove daytime running light from front bumper fascia lower.

INSTALLATION

Install in the reverse order of removal.

1.

Daytime running light 

2.

Front bumper fascia assembly

3.

U nut

4

Harness connector assembly

N·m (kg-m, in-lb)

JMLIA3676GB

Revision: 2013 October

2014 JUKE

FRONT FOG LAMP

EXL-101

< REMOVAL AND INSTALLATION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

FRONT FOG LAMP

Exploded View

INFOID:0000000009754548

Removal and Installation

INFOID:0000000009754549

CAUTION:

Disconnect the battery negative terminal or remove the fuse.

REMOVAL

1.

Remove fender protector. Keep the service area. Refer to 

EXT-27, "Removal and Installation"

.

2.

Disconnect front fog lamp harness connector.

3.

Remove front fog lamp bracket.

4.

Remove front fog lamp mounting bolt, and then remove front fog lamp from front fog lamp bracket.

INSTALLATION

Note the following item, and then installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to 

EXL-94, "Description"

Replacement

INFOID:0000000009754550

CAUTION:

• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

FRONT FOG LAMP BULB

1.

Remove fender protector. Keep the service area. Refer to 

EXT-27, "Removal and Installation"

.

1.

Front fog lamp assembly

2.

Metal clip

3.

Front fog lamp bulb

4.

Front fog lamp bracket

5.

U nut

6.

Front bumper fascia lower

: N·m (kg-m, in-lb)

JMLIA1240GB

Revision: 2013 October

2014 JUKE

EXL-102

< REMOVAL AND INSTALLATION >

[HALOGEN TYPE]

FRONT FOG LAMP

2.

Remove front fog lamp bulb connector (1).

3.

Rotate the bulb (2) counterclockwise and unlock it.

JPLIA0345ZZ

Revision: 2013 October

2014 JUKE

OPTICAL SENSOR

EXL-103

< REMOVAL AND INSTALLATION >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

OPTICAL SENSOR

Exploded View

INFOID:0000000009754551

Removal and Installation

INFOID:0000000009754552

REMOVAL

1.

Insert an appropriate tool between the switch panel and the instrument upper panel. Pull out the optical
sensor upward.

2.

Disconnect the optical sensor connector.

3.

Remove optical sensor from switch panel.

INSTALLATION

Install in the reverse order of removal.

1.

Optical sensor

2.

Switch panel

: Pawl

JMLIA1245ZZ

Revision: 2013 October

2014 JUKE