Nissan Juke (2016 year). Service Repair Manual - part 678

WCS-16

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (COMBINATION METER)

• *1:  CVT  models
• *2:  M/T  models

NOTE:

Some items are not available according to vehicle specification.

Warning History

O/D OFF SW
[Off]

This item is displayed, but cannot be monitored.

M RANGE SW
[On/Off]

Status of manual mode switch.

NM RANGE SW
[On/Off]

Status of non-manual mode switch.

AT SFT UP SW
[On/Off]

Status of manual mode shift up switch.

AT SFT DWN SW
[On/Off]

Status of manual mode shift down switch.

ST SFT UP SW
[On/Off]

Status of paddle shifter up switch.

ST SFT DWN SW
[On/Off]

Status of paddle shifter down switch.

PKB SW
[On/Off]

Status of parking brake switch.

BUCKLE SW
[On/Off]

Status of seat belt buckle switch (driver side).

BRAKE SW
[Off]

This item is displayed, but cannot be monitored.

BRAKE OIL SW
[On/Off]

Status of brake fluid level switch.

A/C AMP CONN
[On/Off]

Status of A/C auto amp. connection recognition signal.

PASS BUCKLE SW
[Off]

This item is displayed, but cannot be monitored.

DISTANCE
[km]

Value of distance to empty calculated by combination meter.

OUTSIDE TEMP
[

°

C or 

°

F]

Ambient temperature value converted from ambient sensor signal received from 
ambient sensor.

NOTE:

This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the ambient 
sensor input value.)

FUEL LOW SIG
[On/Off]

Status of fuel level low warning signal to output to AV control unit via CAN com-
munication.

BUZZER
[On/Off]

X

Buzzer status (in the combination meter) is detected from the buzzer output signal 
received from each unit via CAN communication and the warning output condition 
of the combination meter.

ASCD SPD BLNK
[On/Off]

Blinking status of ASCD or speed limiter set vehicle speed that is judged by the 
ASCD status signal received from ECM via CAN communication.

ASCD STATUS
[Off, ASCD, CRUISE, SL ON, SL 
SET]

Display status of ASCD and speed limiter status display judged by the ASCD sta-
tus signal received from ECM via CAN communication.

ASCD REQ SPD
[km/h/Off]

ASCD or speed limiter set vehicle speed value that is judged by the ASCD status 
signal received from ECM via CAN communication.

TPMS PRESS L
[On/Off]

Status of low tire pressure warning judged from low tire pressure warning lamp 
signal received from BCM with CAN communication line.

Display item [Unit]

MAIN

SIGNALS

Description

Revision: November 2015

2016 JUKE

WCS

DIAGNOSIS SYSTEM (COMBINATION METER)

WCS-17

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

• Stores histories when warning/indicator lamp is turned on.

• “Warning History” indicates the “TIME” when the warning/indicator lamp is turned on.

• The “TIME” above is:

- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine

and waiting for 30 seconds.

- 1 - 39: The number of times the engine was restarted after the 0 condition.

- NO Warning History: Stores NO (0) turning on history of warning/indicator lamp.

NOTE:

• Warning History is not stored for approximately 30 seconds after the engine starts.

• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets

low.

Display Item

NOTE:

In items displayed on the CONSULT screen, only those listed in the above table are used.

Display item

Description

ABS W/L

Lighting history of ABS warning lamp.

VDC/TCS IND

Lighting history of VDC OFF indicator lamp.

SLIP IND

Lighting history of VDC warning lamp.

BRAKE W/L

Lighting history of brake warning lamp.

DOOR W/L

Lighting history of door open warning.

OIL W/L

Lighting history of oil pressure warning lamp.

C-ENG W/L

Lighting history of malfunction indicator lamp.

CRUISE IND

Lighting history of CRUISE indicator lamp.

CVT IND

Lighting history of CVT indicator lamp.

4WD W/L

Lighting history of AWD warning lamp.

FUEL W/L

Lighting history of low fuel level warning lamp.

AIR PRES W/L

Lighting history of low tire pressure warning lamp.

KEY G/Y W/L

Lighting history of KEY warning lamp (G/Y).

KEY KNOB W/L

Lighting history of Shift P warning lamp.

EPS W/L

Lighting history of EPS warning lamp.

Revision: November 2015

2016 JUKE

WCS-18

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000013034218

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.

NOTE:

It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

NOTE:

*: For models with automatic A/C, this diagnosis mode is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on

CONSULT.

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp timer

INT LAMP

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

×

Air conditioning system

AIR CONDITONER

×

×

*

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

×

×

×

Combination switch

COMB SW

×

Body control system

BCM

×

NVIS - NATS

IMMU

×

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door open

TRUNK

×

Theft warning alarm

THEFT ALM

×

×

×

RAP

RETAINED PWR

×

Signal buffer system

SIGNAL BUFFER

×

×

TPMS

AIR PRESSURE MONITOR

×

×

×

Revision: November 2015

2016 JUKE

WCS

DIAGNOSIS SYSTEM (BCM)

WCS-19

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

NOTE:

*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.

BUZZER
BUZZER : CONSULT Function (BCM - BUZZER)

INFOID:0000000012201475

CONSULT APPLICATION ITEMS

CONSULT screen item

Indication/Unit

Description

Vehicle Speed

km/h

Vehicle speed of the moment a particular DTC is detected

Odo/Trip Meter

km

Total mileage (Odometer value) of the moment a particular DTC is detected

Vehicle Condition

SLEEP>LOCK

Power position status of 
the moment a particular 
DTC is detected

While turning BCM status from low power consumption mode to 
normal mode (Power position is “LOCK”*.)

SLEEP>OFF

While turning BCM status from low power consumption mode to 
normal mode (Power position is “OFF”.)

LOCK>ACC

While turning power position from “LOCK”* *to “ACC”

ACC>ON

While turning power position from “ACC” to “IGN”

RUN>ACC

While turning power position from “RUN” to “ACC” (Vehicle is 
stopping and selector lever is except P position.)

CRANK>RUN

While turning power position from “CRANKING” to “RUN” (From 
cranking up the engine to run it)

RUN>URGENT

While turning power position from “RUN“ to “ACC” (Emergency 
stop operation)

ACC>OFF

While turning power position from “ACC” to “OFF”

OFF>LOCK

While turning power position from “OFF” to “LOCK”*

OFF>ACC

While turning power position from “OFF” to “ACC”

ON>CRANK

While turning power position from “IGN” to “CRANKING”

OFF>SLEEP

While turning BCM status from normal mode (Power position is 
“OFF”.) to low power consumption mode

LOCK>SLEEP

While turning BCM status from normal mode (Power position is 
“LOCK”*.) to low power consumption mode

LOCK

Power position is “LOCK”*

OFF

Power position is “OFF” (Ignition switch OFF)

ACC

Power position is “ACC” (Ignition switch ACC)

ON

Power position is “IGN” (Ignition switch ON with engine stopped)

ENGINE RUN

Power position is “RUN” (Ignition switch ON with engine running)

CRANKING

Power position is “CRANKING” (At engine cranking)

IGN Counter

0 - 39

The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1 

→

 2 

→

 3...38 

→

 39 after returning to the normal condition 

whenever ignition switch OFF 

→

 ON.

• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

Test item

Diagnosis mode

Description

BUZZER

Data Monitor

Displays BCM input data in real time.

Active Test

Operation of electrical loads can be checked by sending driving signal to them.

Revision: November 2015

2016 JUKE

WCS-20

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

ACTIVE TEST

Display item

[Unit]

Description

PUSH SW
[On/Off]

Status of push-button ignition switch judged by BCM.

UNLK SEN-DR
[On/Off]

Status of unlock sensor judged by BCM.

VEH SPEED 1
[km/h]

Value of vehicle speed signal received from combination meter with CAN communication line.

TAIL LAMP SW
[On/Off]

Status of lighting switch judged by BCM using the combination switch readout function.

FR FOG SW
[On/Off]

Status of front fog lamp switch judged by BCM using the combination switch readout function.

DOOR SW-DR
[On/Off]

Status of driver side door switch judged by BCM.

CDL LOCK SW
[On/Off]

Status of door lock unlock switch judged by BCM.

Display item

[Unit]

Description

SEAT BELT WARN TEST

The seat belt warning chime operation can be checked by operating the relevant function (On/Off).

KEY REMINDER WARN

The key warning chime operation can be checked by operating the relevant function (On/Off).

LIGHT WARN ALM

The light warning chime operation can be checked by operating the relevant function (On/Off).

Revision: November 2015

2016 JUKE

WCS

COMBINATION METER

WCS-21

< ECU DIAGNOSIS INFORMATION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

ECU DIAGNOSIS INFORMATION

COMBINATION METER

Reference Value

INFOID:0000000012926224

VALUES ON THE DIAGNOSIS TOOL

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

Monitor Item

Condition

Value/Status

SPEED METER
[km/h]

Ignition switch 
ON

While driving

Input value of vehicle speed signal 
(CAN communication signal)

NOTE:

655.35 is displayed when the malfunc-
tion signal is received

SPEED OUTPUT
[km/h]

Ignition switch 
ON

While driving

Output value of vehicle speed signal 
(CAN communication signal)

NOTE:

655.35 is displayed when the malfunc-
tion signal is received

ODO OUTPUT
[km/h or mph]

Ignition switch 
ON

—

Output value of odometer signal (CAN 
communication signal)

TACHO METER
[rpm]

Ignition switch 
ON

Engine running

Input value of engine speed signal 
(CAN communication signal)

NOTE:

8191.875 is displayed when the mal-
function signal is received

FUEL METER
[L]

Ignition switch 
ON

—

Input value of fuel level sensor signal

W TEMP METER
[

°

C]

Ignition switch 
ON

—

Input value of engine coolant tempera-
ture signal (CAN communication sig-
nal)

NOTE:

215 is displayed when the malfunction 
signal is input

FUEL CAP W/L

Ignition switch 
ON

Fuel filler cap warning display ON

On

Fuel filler cap warning display OFF

Off

ABS W/L

Ignition switch 
ON

ABS warning lamp ON

On

ABS warning lamp OFF

Off

VDC/TCS IND

Ignition switch 
ON

VDC OFF indicator lamp ON

On

VDC OFF indicator lamp OFF

Off

SLIP IND

Ignition switch 
ON

VDC warning lamp ON

On

VDC warning lamp OFF

Off

BRAKE W/L

Ignition switch 
ON

Brake warning lamp ON

On

Brake warning lamp OFF

Off

DOOR W/L

Ignition switch 
ON

Door open warning lamp ON

On

Door open warning lamp OFF

Off

HI-BEAM IND

Ignition switch 
ON

High-beam indicator lamp ON

On

High-beam indicator lamp OFF

Off

TURN IND

Ignition switch 
ON

Turn signal indicator lamp ON

On

Turn signal indicator lamp OFF

Off

Revision: November 2015

2016 JUKE

WCS-22

< ECU DIAGNOSIS INFORMATION >

COMBINATION METER

FR FOG IND

Ignition switch 
ON

Front fog lamp indicator lamp ON

On

Front fog lamp indicator lamp OFF

Off

LIGHT IND

Ignition switch 
ON

Tail lamp indicator lamp ON

On

Tail lamp indicator lamp OFF

Off

OIL W/L

Ignition switch 
ON

Oil pressure warning lamp ON

On

Oil pressure warning lamp OFF

Off

MIL

Ignition switch 
ON

Malfunction indicator lamp ON

On

Malfunction indicator lamp OFF

Off

GLOW IND

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

C-ENG2 W/L

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

CRUISE IND

Ignition switch 
ON

CRUISE indicator lamp ON

On

CRUISE indicator lamp OFF

Off

SET IND

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

CVT IND

Ignition switch 
ON

CVT indicator ON

On

CVT indicator OFF

Off

4WD W/L

Ignition switch 
ON

AWD warning lamp ON

On

AWD warning lamp OFF

Off

4WD LOCK IND

Ignition switch 
ON

AWD mode indicator lamp (AWD-V) ON

On

AWD mode indicator lamp (AWD-V) OFF

Off

FUEL W/L

Ignition switch 
ON

During low fuel warning indication

On

Other than the above

Off

AIR PRES W/L

Ignition switch 
ON

Low tire pressure warning lamp ON

On

Other than the above

Off

KEY G/Y W/L

Ignition switch 
ON

During Intelligent Key system malfunction 
indication

On

Other than the above

Off

KEY KNOB W/L

Ignition switch 
ON

SHIFT P warning lamp ON

On

SHIFT P warning lamp OFF

Off

EPS W/L

Ignition switch 
ON

EPS warning lamp ON

On

EPS warning lamp OFF

Off

DPF W/L

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

Monitor Item

Condition

Value/Status

Revision: November 2015

2016 JUKE

WCS

COMBINATION METER

WCS-23

< ECU DIAGNOSIS INFORMATION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

LCD

Ignition switch 
LOCK or ACC

Engine start operation indicator lamp ON 
(CVT models)

B&P N

Ignition switch 
ON

Engine start operation indicator lamp ON 
(CVT models)

B&P I

Ignition switch 
LOCK or ACC

Engine start operation indicator lamp ON 
(M/T models)

C&P N

Ignition switch 
ON

Engine start operation indicator lamp ON 
(M/T models)

C&P I

Ignition switch 
LOCK

During P position warning indication

SFT P

Ignition switch 
LOCK

During Intelligent Key low battery warning 
indication

BATT

Ignition switch 
ON

During take away warning indication

NO KY

Ignition switch 
ON

During ACC warning indication

LK WN

SHIFT IND

Ignition switch 
ON

Shift position indicator P display

P

Shift position indicator R display

R

Shift position indicator N display

N

Shift position indicator D display

D

Shift position indicator M1 display

M1

Shift position indicator M2 display

M2

Shift position indicator M3 display

M3

Shift position indicator M4 display

M4

Shift position indicator M5 display

M5

Shift position indicator M6 display

M6

Shift position indicator M7 display

M7

Shift position indicator M8 display

M8

O/D OFF SW

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

M RANGE SW

Ignition switch 
ON

Selector lever in manual mode position

On

Other than the above

Off

NM RANGE SW

Ignition switch 
ON

Selector lever in manual mode position

Off

Other than the above

On

AT SFT UP SW

Ignition switch 
ON

Selector lever in + position

On

Other than the above

Off

AT SFT DWN SW

Ignition switch 
ON

Selector lever in – position

On

Other than the above

Off

ST SFT UP SW

Ignition switch 
ON

Paddle shifter switch up operation

On

Other than the above

Off

ST SFT DWN SW

Ignition switch 
ON

Paddle shifter switch up operation

On

Other than the above

Off

PKB SW

Ignition switch 
ON

Parking brake switch ON 

On

Parking brake switch OFF

Off

BUCKLE SW

Ignition switch 
ON

Driver seat belt not fastened

On

Driver seat belt fastened

Off

Monitor Item

Condition

Value/Status

Revision: November 2015

2016 JUKE