Content .. 675 676 677 678 ..

Nissan Juke (2016 year). Service Repair Manual - part 677

WCS-8

< SYSTEM DESCRIPTION >

SYSTEM

LIGHT REMINDER WARNING CHIME
LIGHT REMINDER WARNING CHIME : System Diagram

INFOID:0000000012201467

Function

Specifications

Speedometer

Reset to zero by suspending communication.

Tachometer

Illumination control

When suspending communication, changes to nighttime mode.

Shift position indicator

When suspending communication, not indicate.

Information display

Instantaneous fuel consumption

• When reception time of an abnormal signal is 2 seconds or

less, the last received datum is used for calculation to indi-
cate the result.

• When reception time of an abnormal signal is more than two

seconds, the last result calculated during normal condition is
indicated.

Average fuel consumption

Possible driving distance

Torque distribution indicator

Low tire pressure warning

The display turns OFF by suspending communication.

Buzzer

The buzzer turns OFF by suspending communication.

Warning lamp/indicator lamp

ABS warning lamp

The lamp turns ON by suspending communication.

Malfunction indicator lamp

VDC warning lamp

EPS warning lamp

AWD warning lamp

Brake warning lamp

VDC OFF indicator lamp

The lamp turns OFF by suspending communication.

High beam indicator lamp

Turn signal indicator lamp

Door warning lamp

Tail lamp indicator lamp

Engine start operation indicator lamp

Shift P warning lamp

Front fog lamp indicator lamp

Oil pressure warning lamp

CRUISE indicator lamp

AWD mode indicator lamp (AWD)

AWD mode indicator lamp (AWD-V)

Key warning lamp

CVT indicator lamp

Low tire pressure warning lamp

After blinking for 1 minute, the lamp remains ON.

High coolant temperature indicator
lamp

When reception time of an abnormal signal is more than 60
seconds, the lamp turns OFF.

JSNIA2421GB

Revision: November 2015

2016 JUKE

WCS

SYSTEM

WCS-9

< SYSTEM DESCRIPTION >

LIGHT REMINDER WARNING CHIME : System Description

INFOID:0000000012201468

WARNING CHIME OPERATION CONDITIONS

If all of the following conditions are fulfilled.

WARNING CHIME CANCEL CONDITIONS

Warning is canceled if any of the following conditions is fulfilled.

SIGNAL PATH

1. BCM requires warning chime output to combination meter when it judges light reminder warning chime is

necessary from signals below.

2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-

nal) from BCM.

Operation conditions

Ignition switch

OFF or ACC position

Combination switch (Lighting
switch)

1st or 2nd position

Driver side door

Open [front door switch (driver side) ON]

Operation conditions

Ignition switch

Combination switch (Lighting
switch)

OFF or AUTO position

Driver side door

Close [front door switch (driver side) OFF]

Signal name

Signal path

Ignition switch signal

—

Combination switch signal

Combination switch (Lighting switch)

BCM

Driver door switch signal

Front door switch (driver side)

BCM

Signal name

Signal path

Buzzer output signal

BCM

Combination

meter

Revision: November 2015

2016 JUKE

WCS-10

< SYSTEM DESCRIPTION >

SYSTEM

TIMING CHART

SEAT BELT WARNING CHIME
SEAT BELT WARNING CHIME : System Diagram

INFOID:0000000012201469

SEAT BELT WARNING CHIME : System Description

INFOID:0000000012201470

WARNING OPERATION CONDITIONS

If all of the following conditions are fulfilled.

WARNING CANCEL CONDITIONS

Warning is canceled if any of the following conditions is fulfilled.

SIGNAL PATH

1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec-

essary from signals below.

JSNIA2426GB

JSNIA3118GB

Operation conditions

Ignition switch

Driver seat belt

Unfastened [seat belt buckle switch (driver side) ON]

Operation conditions

Ignition switch

OFF

Seat belt (driver side)

Fastened (driver side seat belt buckle switch OFF)

6 seconds after the start of warning sound

Revision: November 2015

2016 JUKE

WCS

SYSTEM

WCS-11

< SYSTEM DESCRIPTION >

2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-

nal) from BCM.

TIMING CHART

SOUND SPECIFICATION

PARKING BRAKE RELEASE WARNING CHIME
PARKING BRAKE RELEASE WARNING CHIME : System Diagram

INFOID:0000000012201471

Signal name

Signal path

Ignition switch signal

—

Seat belt buckle switch signal
(driver side)

Seat belt buckle switch (driver side)

Combination meter

BCM

Signal name

Signal path

Buzzer output signal

BCM

Combination

meter

JSNIA3123GB

JSNIA3111GB

JSNIA2422GB

Revision: November 2015

2016 JUKE

WCS-12

< SYSTEM DESCRIPTION >

SYSTEM

PARKING BRAKE RELEASE WARNING CHIME : System Description

INFOID:0000000012201472

WARNING OPERATION CONDITIONS

If all of the following conditions are fulfilled.

WARNING CANCEL CONDITIONS

Warning is canceled if any of the following conditions are fulfilled.

SIGNAL PATH

Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-

essary from signals below.

TIMING CHART

Operation conditions

Ignition switch

Parking brake

During the operation (parking brake switch ON)

Vehicle speed

Approximately 7 km/h (4.3 MPH) or more

Operation conditions

Ignition switch

OFF

Parking brake

Release condition (parking brake switch OFF)

Vehicle speed

Approximately 3 km/h (1.9 MPH) or less

Signal name

Signal path

Ignition switch signal

—

Parking brake switch signal

Parking brake switch

Combination meter

Vehicle speed signal

ABS actuator and electric unit (control unit)

Combination meter

JSNIA2428GB

Revision: November 2015

2016 JUKE

WCS

SYSTEM

WCS-13

< SYSTEM DESCRIPTION >

SOUND SPECIFICATION

JSNIA3640GB

Revision: November 2015

2016 JUKE

WCS-14

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (COMBINATION METER)

DIAGNOSIS SYSTEM (COMBINATION METER)

CONSULT Function

INFOID:0000000012926221

CONSULT APPLICATION ITEMS

CONSULT can perform the following diagnosis modes via CAN communication and the combination meter.

SELF DIAG RESULT

Refer to

WCS-28, "DTC Index"

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

Display Item List

X: Applicable

System

Diagnosis mode

Description

METER/M&A

Self Diagnostic Result

The combination meter checks the conditions and displays memorized errors.

Data Monitor

Displays the combination meter input/output data in real time.

Warning History

Lighting history of the warning lamp and indicator lamp can be checked.

Display item [Unit]

MAIN

SIGNALS

Description

SPEED METER
[km/h]

Value of vehicle speed signal received from ABS actuator and electric unit (control
unit) via CAN communication.

NOTE:

655.35 is displayed when the malfunction signal is received.

SPEED OUTPUT
[km/h]

Vehicle speed signal value transmitted to other units via CAN communication.

NOTE:

655.35 is displayed when the malfunction signal is received.

ODO OUTPUT
[km/h or mph]

Odometer signal value transmitted to other units via CAN communication.

TACHO METER
[rpm]

• Value of the engine speed signal received from TCM via CAN communication

(CVT models).

• Value of the engine speed signal received from ECM via CAN communication

(M/T models).

NOTE:

8191.875 is displayed when the malfunction signal is received.

FUEL METER
[L]

Fuel level indicated on combination meter.

W TEMP METER
[

Value of engine coolant temperature signal is received from ECM via CAN com-
munication.

NOTE:

215 is displayed when the malfunction signal is input.

FUEL CAP W/L
[On/Off]

Status of fuel filler cap warning display detected from fuel filler cap warning display
signal received from ECM via CAN communication.

ABS W/L
[On/Off]

Status of ABS warning lamp detected from ABS warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.

VDC/TCS IND
[On/Off]

Status of VDC OFF indicator lamp detected from VDC OFF indicator lamp signal
is received from ABS actuator and electric unit (control unit) via CAN communica-
tion.

SLIP IND
[On/Off]

Status of VDC warning lamp detected from VDC warning lamp signal received
from ABS actuator and electric unit (control unit) via CAN communication.

Revision: November 2015

2016 JUKE

WCS

DIAGNOSIS SYSTEM (COMBINATION METER)

WCS-15

< SYSTEM DESCRIPTION >

BRAKE W/L
[On/Off]

Status of brake warning lamp detected from brake warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.

NOTE:

Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.

DOOR W/L
[On/Off]

Status of door open warning lamp detected from door switch signal received from
BCM via CAN communication.

HI-BEAM IND
[On/Off]

Status of high beam indicator lamp detected from high beam request signal is re-
ceived from BCM via CAN communication.

TURN IND
[On/Off]

Status of turn indicator lamp detected from turn indicator signal is received from
BCM via CAN communication.

LIGHT IND
[On/Off]

Status of tail lamp indicator lamp detected from position light request signal is re-
ceived from BCM via CAN communication.

FR FOG IND
[On/Off]

Status of front fog light indicator lamp detected from front fog light request signal
is received from BCM via CAN communication.

OIL W/L
[On/Off]

Status of oil pressure warning lamp detected from oil pressure warning lamp sig-
nal is received from ECM via CAN communication.

MIL
[On/Off]

Status of malfunction indicator lamp detected from malfunctioning indicator lamp
signal is received from ECM via CAN communication.

GLOW IND
[Off]

This item is displayed, but cannot be monitored.

C-ENG2 W/L
[Off]

This item is displayed, but cannot be monitored.

CRUISE IND
[On/Off]

Status of CRUISE indicator lamp detected from ASCD status signal is received
from ECM via CAN communication.

SET IND
[Off]

This item is displayed, but cannot be monitored.

CVT IND
[On/Off]

Status of CVT indicator lamp detected from CVT status signal is received from
TCM via CAN communication.

4WD W/L
[On/Off]

Status of AWD warning lamp judged from AWD warning lamp signal received from
AWD control module with CAN communication line.

4WD LOCK IND
[On/Off]

Status of AWD mode indicator lamp (AWD-V) judged from AWD mode indicator
signal received from AWD control module with CAN communication line.

FUEL W/L
[On/Off]

Low fuel warning status detected by the identified fuel level.

AIR PRES W/L
[On/Off]

Status of low tire pressure warning lamp judged from low tire pressure warning
lamp signal received from BCM from CAN communication line.

KEY G/Y W/L
[On/Off]

Status of KEY warning lamp (G/Y) detected from KEY warning lamp signal is re-
ceived from BCM via CAN communication.

KEY KNOB W/L
[On/Off]

Status of shift P warning lamp detected from shift P warning lamp signal is re-
ceived from BCM via CAN communication.

EPS W/L
[On/Off]

Status of EPS warning lamp detected from EPS warning lamp signal is received
from EPS control unit via CAN communication.

DPF W/L
[Off]

This item is displayed, but cannot be monitored.

LCD
[B&P N, B&P I, SFT P, BATT, NO KY,
LK WN]

[C&P N, C&P I, SFT P, BATT, NO KY,
LK WN]

Status of engine start operation indicator lamp, shift P warning lamp and KEY
warning lamp, detected from engine start operation indicator lamp signal, shift P
warning lamp signal and KEY warning lamp signal are received from BCM via
CAN communication.

SHIFT IND
[P, R, N, D, M1, M2, M3,
M4, M5, M6, M7, M8]

Status of shift position indicator judged from shift position signal received from
TCM with CAN communication line.

Display item [Unit]

MAIN

SIGNALS

Description

Revision: November 2015

2016 JUKE

Content .. 675 676 677 678 ..