Nissan Juke (2016 year). Service Repair Manual - part 500

MWI-24

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (COMBINATION METER)

• *1:  CVT  models
• *2:  M/T  models

NOTE:

Some items are not available according to vehicle specification.

Warning History

O/D OFF SW
[Off]

This item is displayed, but cannot be monitored.

M RANGE SW
[On/Off]

Status of manual mode switch.

NM RANGE SW
[On/Off]

Status of non-manual mode switch.

AT SFT UP SW
[On/Off]

Status of manual mode shift up switch.

AT SFT DWN SW
[On/Off]

Status of manual mode shift down switch.

ST SFT UP SW
[On/Off]

Status of paddle shifter up switch.

ST SFT DWN SW
[On/Off]

Status of paddle shifter down switch.

PKB SW
[On/Off]

Status of parking brake switch.

BUCKLE SW
[On/Off]

Status of seat belt buckle switch (driver side).

BRAKE SW
[Off]

This item is displayed, but cannot be monitored.

BRAKE OIL SW
[On/Off]

Status of brake fluid level switch.

A/C AMP CONN
[On/Off]

Status of A/C auto amp. connection recognition signal.

PASS BUCKLE SW
[Off]

This item is displayed, but cannot be monitored.

DISTANCE
[km]

Value of distance to empty calculated by combination meter.

OUTSIDE TEMP
[

°

C or 

°

F]

Ambient temperature value converted from ambient sensor signal received from 
ambient sensor.

NOTE:

This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the ambient 
sensor input value.)

FUEL LOW SIG
[On/Off]

Status of fuel level low warning signal to output to AV control unit via CAN com-
munication.

BUZZER
[On/Off]

X

Buzzer status (in the combination meter) is detected from the buzzer output signal 
received from each unit via CAN communication and the warning output condition 
of the combination meter.

ASCD SPD BLNK
[On/Off]

Blinking status of ASCD or speed limiter set vehicle speed that is judged by the 
ASCD status signal received from ECM via CAN communication.

ASCD STATUS
[Off, ASCD, CRUISE, SL ON, SL 
SET]

Display status of ASCD and speed limiter status display judged by the ASCD sta-
tus signal received from ECM via CAN communication.

ASCD REQ SPD
[km/h/Off]

ASCD or speed limiter set vehicle speed value that is judged by the ASCD status 
signal received from ECM via CAN communication.

TPMS PRESS L
[On/Off]

Status of low tire pressure warning judged from low tire pressure warning lamp 
signal received from BCM with CAN communication line.

Display item [Unit]

MAIN

SIGNALS

Description

Revision: November 2015

2016 JUKE

MWI

DIAGNOSIS SYSTEM (COMBINATION METER)

MWI-25

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

• Stores histories when warning/indicator lamp is turned on.

• “Warning History” indicates the “TIME” when the warning/indicator lamp is turned on.

• The “TIME” above is:

- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine

and waiting for 30 seconds.

- 1 - 39: The number of times the engine was restarted after the 0 condition.

- NO Warning History: Stores NO (0) turning on history of warning/indicator lamp.

NOTE:

• Warning History is not stored for approximately 30 seconds after the engine starts.

• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets

low.

Display Item

NOTE:

In items displayed on the CONSULT screen, only those listed in the above table are used.

Display item

Description

ABS W/L

Lighting history of ABS warning lamp.

VDC/TCS IND

Lighting history of VDC OFF indicator lamp.

SLIP IND

Lighting history of VDC warning lamp.

BRAKE W/L

Lighting history of brake warning lamp.

DOOR W/L

Lighting history of door open warning.

OIL W/L

Lighting history of oil pressure warning lamp.

C-ENG W/L

Lighting history of malfunction indicator lamp.

CRUISE IND

Lighting history of CRUISE indicator lamp.

CVT IND

Lighting history of CVT indicator lamp.

4WD W/L

Lighting history of AWD warning lamp.

FUEL W/L

Lighting history of low fuel level warning lamp.

AIR PRES W/L

Lighting history of low tire pressure warning lamp.

KEY G/Y W/L

Lighting history of KEY warning lamp (G/Y).

KEY KNOB W/L

Lighting history of Shift P warning lamp.

EPS W/L

Lighting history of EPS warning lamp.

Revision: November 2015

2016 JUKE

MWI-26

< ECU DIAGNOSIS INFORMATION >

COMBINATION METER

ECU DIAGNOSIS INFORMATION

COMBINATION METER

Reference Value

INFOID:0000000012201315

VALUES ON THE DIAGNOSIS TOOL

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

Monitor Item

Condition

Value/Status

SPEED METER
[km/h]

Ignition switch 
ON

While driving

Input value of vehicle speed signal 
(CAN communication signal)

NOTE:

655.35 is displayed when the malfunc-
tion signal is received

SPEED OUTPUT
[km/h]

Ignition switch 
ON

While driving

Output value of vehicle speed signal 
(CAN communication signal)

NOTE:

655.35 is displayed when the malfunc-
tion signal is received

ODO OUTPUT
[km/h or mph]

Ignition switch 
ON

—

Output value of odometer signal (CAN 
communication signal)

TACHO METER
[rpm]

Ignition switch 
ON

Engine running

Input value of engine speed signal 
(CAN communication signal)

NOTE:

8191.875 is displayed when the mal-
function signal is received

FUEL METER
[L]

Ignition switch 
ON

—

Input value of fuel level sensor signal

W TEMP METER
[

°

C]

Ignition switch 
ON

—

Input value of engine coolant tempera-
ture signal (CAN communication sig-
nal)

NOTE:

215 is displayed when the malfunction 
signal is input

FUEL CAP W/L

Ignition switch 
ON

Fuel filler cap warning display ON

On

Fuel filler cap warning display OFF

Off

ABS W/L

Ignition switch 
ON

ABS warning lamp ON

On

ABS warning lamp OFF

Off

VDC/TCS IND

Ignition switch 
ON

VDC OFF indicator lamp ON

On

VDC OFF indicator lamp OFF

Off

SLIP IND

Ignition switch 
ON

VDC warning lamp ON

On

VDC warning lamp OFF

Off

BRAKE W/L

Ignition switch 
ON

Brake warning lamp ON

On

Brake warning lamp OFF

Off

DOOR W/L

Ignition switch 
ON

Door open warning lamp ON

On

Door open warning lamp OFF

Off

HI-BEAM IND

Ignition switch 
ON

High-beam indicator lamp ON

On

High-beam indicator lamp OFF

Off

TURN IND

Ignition switch 
ON

Turn signal indicator lamp ON

On

Turn signal indicator lamp OFF

Off

Revision: November 2015

2016 JUKE

MWI

COMBINATION METER

MWI-27

< ECU DIAGNOSIS INFORMATION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

FR FOG IND

Ignition switch 
ON

Front fog lamp indicator lamp ON

On

Front fog lamp indicator lamp OFF

Off

LIGHT IND

Ignition switch 
ON

Tail lamp indicator lamp ON

On

Tail lamp indicator lamp OFF

Off

OIL W/L

Ignition switch 
ON

Oil pressure warning lamp ON

On

Oil pressure warning lamp OFF

Off

MIL

Ignition switch 
ON

Malfunction indicator lamp ON

On

Malfunction indicator lamp OFF

Off

GLOW IND

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

C-ENG2 W/L

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

CRUISE IND

Ignition switch 
ON

CRUISE indicator lamp ON

On

CRUISE indicator lamp OFF

Off

SET IND

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

CVT IND

Ignition switch 
ON

CVT indicator ON

On

CVT indicator OFF

Off

4WD W/L

Ignition switch 
ON

AWD warning lamp ON

On

AWD warning lamp OFF

Off

4WD LOCK IND

Ignition switch 
ON

AWD mode indicator lamp (AWD-V) ON

On

AWD mode indicator lamp (AWD-V) OFF

Off

FUEL W/L

Ignition switch 
ON

During low fuel warning indication

On

Other than the above

Off

AIR PRES W/L

Ignition switch 
ON

Low tire pressure warning lamp ON

On

Other than the above

Off

KEY G/Y W/L

Ignition switch 
ON

During Intelligent Key system malfunction 
indication

On

Other than the above

Off

KEY KNOB W/L

Ignition switch 
ON

SHIFT P warning lamp ON

On

SHIFT P warning lamp OFF

Off

EPS W/L

Ignition switch 
ON

EPS warning lamp ON

On

EPS warning lamp OFF

Off

DPF W/L

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

Monitor Item

Condition

Value/Status

Revision: November 2015

2016 JUKE

MWI-28

< ECU DIAGNOSIS INFORMATION >

COMBINATION METER

LCD

Ignition switch 
LOCK or ACC

Engine start operation indicator lamp ON 
(CVT models)

B&P N

Ignition switch 
ON

Engine start operation indicator lamp ON 
(CVT models)

B&P I

Ignition switch 
LOCK or ACC

Engine start operation indicator lamp ON 
(M/T models)

C&P N

Ignition switch 
ON

Engine start operation indicator lamp ON 
(M/T models)

C&P I

Ignition switch 
LOCK

During P position warning indication

SFT P

Ignition switch 
LOCK

During Intelligent Key low battery warning 
indication

BATT

Ignition switch 
ON

During take away warning indication

NO KY

Ignition switch 
ON

During ACC warning indication

LK WN

SHIFT IND

Ignition switch 
ON

Shift position indicator P display

P

Shift position indicator R display

R

Shift position indicator N display

N

Shift position indicator D display

D

Shift position indicator M1 display

M1

Shift position indicator M2 display

M2

Shift position indicator M3 display

M3

Shift position indicator M4 display

M4

Shift position indicator M5 display

M5

Shift position indicator M6 display

M6

Shift position indicator M7 display

M7

Shift position indicator M8 display

M8

O/D OFF SW

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

M RANGE SW

Ignition switch 
ON

Selector lever in manual mode position

On

Other than the above

Off

NM RANGE SW

Ignition switch 
ON

Selector lever in manual mode position

Off

Other than the above

On

AT SFT UP SW

Ignition switch 
ON

Selector lever in + position

On

Other than the above

Off

AT SFT DWN SW

Ignition switch 
ON

Selector lever in – position

On

Other than the above

Off

ST SFT UP SW

Ignition switch 
ON

Paddle shifter switch up operation

On

Other than the above

Off

ST SFT DWN SW

Ignition switch 
ON

Paddle shifter switch up operation

On

Other than the above

Off

PKB SW

Ignition switch 
ON

Parking brake switch ON 

On

Parking brake switch OFF

Off

BUCKLE SW

Ignition switch 
ON

Driver seat belt not fastened

On

Driver seat belt fastened

Off

Monitor Item

Condition

Value/Status

Revision: November 2015

2016 JUKE

MWI

COMBINATION METER

MWI-29

< ECU DIAGNOSIS INFORMATION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

NOTE:

Some items are not available according to vehicle specification.

TERMINAL LAYOUT

PHYSICAL VALUES

BRAKE SW

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

BRAKE OIL SW

Ignition switch 
ON

Brake fluid level switch ON

On

Brake fluid level switch OFF

Off

A/C AMP CONN

Ignition switch 
ON

Other than the following

On

Receives A/C auto amp. connection recog-
nition signal

Off

PASS BUCKLE SW

Ignition switch 
ON

NOTE:

This item is displayed, but cannot be moni-
tored.

Off

DISTANCE
[km]

Ignition switch 
ON

—

Distance to empty calculated by com-
bination meter

OUTSIDE TEMP
[

°

C or 

°

F]

Ignition switch 
ON

—

Input value of ambient sensor signal 
(CAN communication signal)

NOTE:

This may not match the indicated value 
on the information display.

FUEL LOW SIG

Ignition switch 
ON

During low fuel warning indication

On

Other than above

Off

BUZZER

Ignition switch 
ON

Buzzer ON

On

Buzzer OFF

Off

ASCD SPD BLNK

Ignition switch 
ON

Set vehicle speed indicator blinking

On

Set vehicle speed indicator not blinking

Off

ASCD STATUS

Ignition switch 
ON

ASCD and speed limiter system OFF

Off

ASCD system ON

ASCD

ASCD set vehicle speed

CRUISE

ASCD REQ SPD
[km/h or Off]

Ignition switch 
ON

While driving

Same value as ASCD or speed limiter 
set vehicle speed

TPMS PRESS L

Ignition switch 
ON

Low tire pressure warning display ON

On

Low tire pressure warning display OFF

Off

Monitor Item

Condition

Value/Status

JSNIA0623ZZ

Revision: November 2015

2016 JUKE

MWI-30

< ECU DIAGNOSIS INFORMATION >

COMBINATION METER

Terminal No.

(Wire color)

Description

Condition

Value

(Approx.)

+

–

Signal name

Input/

Output

1

(L)

—

CAN-H

—

—

—

—

2

(P)

—

CAN-L

—

—

—

—

4

(Y)

Ground

Vehicle speed signal
(8-pulse)

Output

Ignition 
switch 
ON

Speedometer operated 
[When vehicle speed is ap-
prox. 40 km/h (25 MPH)]

NOTE:

The maximum voltage varies de-
pending on the specification 
(destination unit).

5

(G)

Ground

Paddle shifter up switch 
signal

Input

Ignition 
switch 
ON

Paddle shifter up operated

0 V

Other than the above

12 V

6

(BR)

Ground Fuel level sensor signal

Input

Ignition 
switch 
ON

—

2WD

AWD

7

(R)

Ground

Air bag signal

Input

Ignition 
switch 
ON

Air bag warning lamp
ON

4 V

Air bag warning lamp
OFF

0 V

8

*1

(P)

—

—

—

—

—

—

9

(W)

Ground

Seat belt buckle switch sig-
nal (driver side)

Input

Engine 
idling

When driver seat belt is fas-
tened.

12 V

When driver seat belt is un-
fastened.

0 V

10

(SB)

Ground

Parking brake switch signal

Input

Ignition 
switch 
ON

Parking brake applied.

0 V

Parking brake released.

5 V

11

(G)

Ground

Brake fluid level switch sig-
nal

Input

Ignition 
switch 
ON

Brake fluid level is normal

5 V

Brake fluid level is less than 
LOW level

0 V

JSNIA0012GB

JSNIA3305ZZ

JSNIA3721ZZ

Revision: November 2015

2016 JUKE

MWI

COMBINATION METER

MWI-31

< ECU DIAGNOSIS INFORMATION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

13

(GR)

Ground Illumination control signal

Output

Ignition 
switch 
ON

• Lighting switch 1ST
• When meter illumination 

is maximum

• Lighting switch 1ST
• When meter illumination 

is step 6

• Lighting switch 1ST
• When meter illumination 

is minimum

12 V

14

(R)

Ground

Manual mode shift up sig-
nal

Input

Ignition 
switch 
ON

Selector lever UP operation

0 V

Other than the above

12 V

15

(L)

Ground

ACC power supply

Input

Ignition 
switch 
ACC

—

Battery voltage

16

(W)

Ground

Manual mode shift down 
signal

Input

Ignition 
switch 
ON

Selector lever DOWN oper-
ation

0 V

Other than the above

12 V

17

(G)

Ground

Washer level switch signal

Input

Ignition 
switch 
ON

Low washer fluid warning 
lamp ON

0 V

Low washer fluid warning 
lamp OFF

12 V

18

(R)

Ground

Security signal

Input

Ignition 
switch 
ON

Security indicator lamp ON

0 V

Security indicator lamp 
OFF

12 V

19

(GR)

Ground Ambient sensor signal

Input

Ignition 
switch 
ON

Changes depending to am-
bient temperature.

20

(R)

Ground Ambient sensor ground

—

Ignition 
switch 
ON

—

0  V

21

(B)

Ground Ground

—

Ignition 
switch 
ON

—

0  V

22

(B)

Ground Ground

—

Ignition 
switch 
ON

—

0  V

Terminal No.

(Wire color)

Description

Condition

Value

(Approx.)

+

–

Signal name

Input/

Output

JPNIA1687GB

JPNIA1686GB

JSNIA0014GB

Revision: November 2015

2016 JUKE