Content .. 393 394 395 396 ..

Nissan Juke (2016 year). Service Repair Manual - part 395

FRONT DRIVE SHAFT

FAX-101

< REMOVAL AND INSTALLATION >

[TYPE 2]

FAX

CAUTION:

• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel

hub lock nut.

• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.

• Never reuse wheel hub lock nut.

NOTE:

Wheel hub lock nut tightening torque does not over torque for avoiding axle noise, and does not less than

torque for avoiding looseness.

• Align the matching marks that have been made during removal when reusing the disc rotor.

• When installing a cotter pin (1) and adjusting cap (2), securely

bend the basal portion to prevent rattles.

CAUTION:

Never reuse cotter pin.

• Perform the final tightening of each of parts under unladen conditions, which were removed when removing

wheel hub assembly and steering knuckle.

• Perform inspection after installation. Refer to

FAX-108, "AWD : Inspection"

AWD : Disassembly and Assembly

INFOID:0000000012201566

DISASSEMBLY

Wheel Side

1. Fix shaft with a vise.

CAUTION:

Protect shaft using aluminum or copper plates when fixing with a vise.

2. Remove boot bands, and then remove boot from joint sub-assembly.
3. Screw drive shaft puller (A) (commercial service tool) into joint

sub-assembly screw part to a length of 30 mm (1.18 in) or more.

Support drive shaft with one hand and pull out joint sub-assem-

bly from shaft.

CAUTION:

• Align drive shaft puller and drive shaft and remove them

by pulling firmly and uniformly.

• If joint sub-assembly cannot be removed after five or

more unsuccessful attempts, replace shaft and joint sub

assembly as a set.

4. Remove circular clip from shaft.
5. Remove boot from shaft.

Transaxle Side (Left Drive Shaft)

1. Fix shaft with a vise.

CAUTION:

Protect shaft using aluminum or copper plates when fixing with a vise.

2. Remove wheel side boot from joint sub-assembly. Refer to

FAX-76, "AWD : Removal and Installation"

3. Remove dynamic damper as per the following instructions:
a. Remove damper band.

: 180 – 185 N·m (18.4 – 18.8 kg-m, 133 – 136 ft-lb)

JPDIF0295ZZ

JPDIG0151ZZ

Revision: November 2015

2016 JUKE

FAX-102

< REMOVAL AND INSTALLATION >

[TYPE 2]

FRONT DRIVE SHAFT

b. Remove dynamic damper from housing assembly.
4. Remove boot bands, then remove boot from housing assembly.
5. Remove circular clip from housing assembly.
6. Remove dust shield from housing assembly.

Transaxle Side (Right Drive Shaft)

1. Fix shaft with a vise.

CAUTION:

Protect shaft using aluminum or copper plates when fixing with a vise.

2. Remove wheel side boot from joint sub-assembly. Refer to

FAX-76, "AWD : Removal and Installation"

3. Remove dynamic damper as per the following instructions:
a. Remove damper band.
b. Remove dynamic damper from housing assembly.
4. Remove boot bands, then remove boot from housing assembly.

ASSEMBLY

Wheel Side

1. Clean the old grease on joint sub-assembly with paper waste.
2. Fill serration slot joint sub-assembly (1) with NISSAN genuine

grease or equivalent until the serration slot and ball groove

become full to the brim.

CAUTION:

After applying grease, use a paper waste to wipe off old

grease that has oozed out.

3. Install boot and boot bands to shaft.

CAUTION:

• Wrap serration on shaft with tape (A) to protect the boot

from damage.

• Never reuse boot and boot band.

4. Remove the tape wrapped around the serration on shaft.

5. Position the circular clip (1) on groove at the shaft edge.

CAUTION:

Never reuse circular clip.

NOTE:

Drive joint inserter is recommended when installing circular clip.

JPDIF0008ZZ

JPDIF0009ZZ

JPDIF0305ZZ

Revision: November 2015

2016 JUKE

FRONT DRIVE SHAFT

FAX-103

< REMOVAL AND INSTALLATION >

[TYPE 2]

FAX

6. Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with joint sub-

assembly holding circular clip.

7. Install joint sub-assembly to shaft using plastic hammer.

CAUTION:

• Check circular clip is properly positioned on groove of the

joint sub-assembly.

• Confirm that joint sub-assembly is correctly engaged

while rotating drive shaft.

8. Apply the specified amount of grease into the boot inside from large diameter side of boot.

9. Install the boot securely into grooves (indicated by “*” marks)

shown in the figure.

CAUTION:

If grease adheres to the boot mounting surface (indicated

by “*” marks) on the shaft or joint sub-assembly, boot may

be removed. Remove all grease from the boot mounting

surface.

10. To prevent the deformation of the boot, adjust the boot installation length (L) to the specified value shown

below by inserting the suitable tool into inside of the boot from the large diameter side of the boot and dis-

charging the inside air.

CAUTION:

• If the boot installation length exceeds the standard, it may cause breakage of the boot.

• Be careful not to touch the inside of the boot with a tip of tool.

11. Secure the large and small ends of the boot with boot bands

using the boot band crimping tool (A) [SST:KV40107300 ( —

)].

CAUTION:

• Never reuse boot band.

RAC0049D

Grease amount

: Refer to

FAX-109, "Drive Shaft"

JSDIA2261ZZ

L : Refer to

FAX-109, "Drive Shaft"

JPDIF0012ZZ

Revision: November 2015

2016 JUKE

FAX-104

< REMOVAL AND INSTALLATION >

[TYPE 2]

FRONT DRIVE SHAFT

• Secure boot band so that dimension (M) meets the speci-

fication as shown in the figure.

12. Check that displacement does not occur when boot is rotated with the joint sub-assembly and shaft fixed.

CAUTION:

• Reinstall them using boot bands when boot installation positions become incorrect.

• Never reuse boot band.

Transaxle Side (Left Drive Shaft)

1. Clean the old grease on housing assembly with paper waste.
2. Install dust shield to housing assembly.

CAUTION:

Never reuse dust shield.

3. Install circular clip to housing.

CAUTION:

Never reuse circular clip.

4. Install boot and boot bands to housing assembly.

CAUTION:

• Wrap serration on housing assembly with tape (A) to pro-

tect the boot from damage.

• Never reuse boot and boot band.

5. Remove the tape wrapped around the serration on shaft.
6. Apply NISSAN genuine grease (refer to parts catalog) to housing assembly.

7. Install the boot securely into grooves (indicated by “*” marks)

shown in the figure.

CAUTION:

If grease adheres to the boot mounting surface (indicated

by “*” marks) on the shaft or housing assembly, boot may

be removed. Remove all grease from the boot mounting

surface.

8. To prevent the deformation of the boot, adjust the boot installation length to the value shown below (L) by

inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging

inside air.

Dimension (M)

: 2.0 – 3.0 mm (0.079 – 0.118 in)

DSF0047D

JSDIA2232ZZ

Grease amount

: Refer to

FAX-109, "Drive Shaft"

JSDIA2063ZZ

Revision: November 2015

2016 JUKE

FRONT DRIVE SHAFT

FAX-105

< REMOVAL AND INSTALLATION >

[TYPE 2]

FAX

CAUTION:

• If the boot installation length exceeds the standard, it may cause breakage of the boot.

• Be careful not to touch the inside of the boot with the tip of tool.

9. Install boot bands securely.

CAUTION:

Never reuse boot bands.

a. Put boot band in the groove on drive shaft boot. Then fit pawls

(

) into holes to temporary installation.

NOTE:

For the large diameter side, fit projection (A) and guide slit (B) at

first.

b. Pinch projection on the band with suitable pliers to tighten band.
c. Insert the tip of band into the lower part of pawl (marked with

dotted circle) as shown in the figure.

10. Check that displacement does not occur when boot is rotated with the housing assembly fixed.

CAUTION:

• If displacement occurs, reinstall band.

• Never reuse boot band.

11. Install dynamic damper, follow the procedure described below.
a. Install dynamic damper to shaft.

b. Secure dynamic damper with bands in the following specified

position (A) when installing.

CAUTION:

Never reuse boot bands.

: Refer to

FAX-109, "Drive Shaft"

JPDIF0157ZZ

JPDIF0158ZZ

A :

Refer

FAX-109, "Drive Shaft"

JPDIF0178ZZ

Revision: November 2015

2016 JUKE

FAX-106

< REMOVAL AND INSTALLATION >

[TYPE 2]

FRONT DRIVE SHAFT

Install boot bands securely as showin in the figure.

12. Install boot to the wheel side. Refer to

FAX-76, "AWD : Removal and Installation"

Transaxle Side (Right Drive Shaft)

1. Clean the old grease on housing assembly with paper waste.
2. Install boot and boot bands to housing assembly.

CAUTION:

• Wrap serration on housing assembly with tape (A) to pro-

tect the boot from damage.

• Never reuse boot and boot band.

3. Remove the tape wrapped around the serration on shaft.
4. Apply NISSAN genuine grease (refer to parts catalog) to housing assembly.

5. Install the boot securely into grooves (indicated by “*” marks)

shown in the figure.

CAUTION:

If grease adheres to the boot mounting surface (indicated

by “*” marks) on the shaft or housing assembly, boot may

be removed. Remove all grease from the boot mounting

surface.

6. To prevent the deformation of the boot, adjust the boot installation length to the value shown below (L) by

inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging

inside air.

CAUTION:

• If the boot installation length exceeds the standard, it may cause breakage of the boot.

• Be careful not to touch the inside of the boot with the tip of tool.

7. Install boot bands securely.

CAUTION:

Never reuse boot bands.

PDIA1188J

JSDIA2232ZZ

Grease amount

: Refer to

FAX-109, "Drive Shaft"

JSDIA2063ZZ

: Refer to

FAX-109, "Drive Shaft"

Revision: November 2015

2016 JUKE

FRONT DRIVE SHAFT

FAX-107

< REMOVAL AND INSTALLATION >

[TYPE 2]

FAX

a. Put boot band in the groove on drive shaft boot. Then fit pawls

(

) into holes to temporary installation.

NOTE:

For the large diameter side, fit projection (A) and guide slit (B) at

first.

b. Pinch projection on the band with suitable pliers to tighten band.
c. Insert the tip of band into the lower part of pawl (marked with

dotted circle) as shown in the figure.

8. Check that displacement does not occur when boot is rotated with the housing assembly fixed.

CAUTION:

• If displacement occurs, reinstall band.

• Never reuse boot band.

9. Install dynamic damper, follow the procedure described below.
a. Install dynamic damper to shaft.
b. Secure dynamic damper with bands in the following specified

position (A) when installing.

CAUTION:

Never reuse bands.

c. Install boot bands securely as showin in the figure.

10. Install boot to the wheel side. Refer to

FAX-76, "AWD : Removal and Installation"

JPDIF0157ZZ

JPDIF0158ZZ

A :

Refer

FAX-109, "Drive Shaft"

JPDIF0178ZZ