Nissan Juke F15. Manual - part 781

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

FAX-63

< SYMPTOM DIAGNOSIS >

[TYPE 2]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

SYMPTOM DIAGNOSIS

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000012201548

Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.

×: Applicable

Reference

—

F

AX-96

 (2WD), 

F

AX-108

 (A

WD)

—

FA

X

-6

6

—

FA

X

-6

8

NVH in 

FAX 

and FS

U sections

Re

fe

r to

 FRO

N

T A

X

L

E in

 th

is

 ch

art

NVH in WT 

section

NVH in WT 

section

Refe

r to

 DRIVE 

SHAFT i

n t

hi

s cha

rt

NVH in BR 

section

NVH in ST 

section

Possible cause and SUSPECTED PARTS

Exc

e

ss

iv

e j

oin

t a

ng

le

Jo

in

t s

lid

in

g re

si

stan

ce

Im

ba

lan

ce

Im

pro

per in

st

a

lla

tion

, lo

os

en

es

s

Part

s int

erference

Whe

el

 be

ari

ng

 da

m

age

FRONT AXLE AND F

R

ONT

 SUSPENSI

ON

FRONT AXLE

TIRE

ROA

D

 WHEEL

DRIVE SHA

F

T

BRAKE

STEERI

N

G

Symptom

DRIVE 
SHAFT

Noise

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

FRONT 
AXLE

Noise

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

Vibration

×

×

×

×

×

×

×

Shimmy

×

×

×

×

×

×

×

Judder

×

×

×

×

×

×

Poor quality ride or handling

×

×

×

×

×

FAX-64

< PERIODIC MAINTENANCE >

[TYPE 2]

FRONT WHEEL HUB AND KNUCKLE

PERIODIC MAINTENANCE

FRONT WHEEL HUB AND KNUCKLE

Inspection

INFOID:0000000012201549

COMPONENT PART

Check that the mounting conditions (looseness, backlash) of each component and component conditions

(wear, damage) are normal.

WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)

Check the following items, and replace the part if necessary.

• Move wheel hub assembly in the axial direction by hand. Check there is no looseness of wheel bearing.

• Rotate wheel hub assembly and check there is no unusual noise or other irregular conditions. If there is any

of irregular conditions, replace wheel hub assembly.

Axial end play

: Refer to 

FAX-109, "Wheel Bear-

ing"

.

FRONT DRIVE SHAFT

FAX-65

< PERIODIC MAINTENANCE >

[TYPE 2]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

FRONT DRIVE SHAFT

Inspection

INFOID:0000000012201550

Check the following items, and replace the part if necessary.

• Check drive shaft mounting point and joint for looseness and other damage.

CAUTION:

Replace entire drive shaft assembly when noise or vibration occurs from drive shaft.

• Check boot for cracks and other damage.

FAX-66

< REMOVAL AND INSTALLATION >

[TYPE 2]

FRONT WHEEL HUB AND KNUCKLE

REMOVAL AND INSTALLATION

FRONT WHEEL HUB AND KNUCKLE

Exploded View

INFOID:0000000012201551

Removal and Installation

INFOID:0000000012201552

REMOVAL

1. Remove tires with power tool. Refer to 

WT-39, "Removal and Installation"

. 

2. Remove wheel sensor and sensor harness. Refer to 

BRC-147, "FRONT WHEEL SENSOR : Exploded

View"

.

3. Remove lock plate from strut assembly. Refer to 

BR-25, "FRONT : Removal and Installation"

.

4. Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to 

BR-55, "BRAKE

CALIPER ASSEMBLY : Removal and Installation"

.

CAUTION:

Never depress brake pedal while brake caliper is removed.

5. Remove disc rotor.

CAUTION:

1.

Steering knuckle

2.

Splash guard

3.

Hub bolt

4.

Wheel hub assembly (Bearing-inte-
grated type)

5.

Disc rotor

6.

Wheel hub lock nut

7.

Adjusting cap

8.

Cotter pin

A. Tightening must be done following the installation procedure. Refer to 

FAX-66, "Removal and Installation"

.

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JPDIF0293GB