Nissan Juke F15. Manual - part 742

EXL-188

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

HAZARD SWITCH

HAZARD SWITCH

Component Function Check

INFOID:0000000012201765

1.

CHECK HAZARD SWITCH SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “FLASHER” of “BCM” using CONSULT.

3. Select “HAZARD SW” in “Data Monitor” mode.

4. With operating the hazard switch, check the monitor status.

Is the inspection result normal?

YES

>> Hazard switch circuit is normal.

NO

>> Refer to 

EXL-188, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201766

1.

CHECK HAZARD SWITCH SIGNAL

1. Turn ignition switch OFF.

2. Disconnect hazard switch connector.

3. Check voltage between hazard switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK HAZARD SWITCH SIGNAL CIRCUIT (OPEN)

1. Disconnect BCM connector.

2. Check continuity between hazard switch harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK HAZARD SWITCH SIGNAL CIRCUIT (SHORT)

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Monitor item

Condition

Monitor status

HAZARD SW

Hazard switch

ON

On

OFF

Off

+

-

Voltage

(Approx.)

Hazard switch

Connector

Terminal

M45

2

Ground

12 V

Hazard switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M45

2

M68

29

Existed

Hazard switch

—

Continuity

Connector

Terminal

M45

2

Ground

Not existed

HAZARD SWITCH

EXL-189

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

NO

>> Repair or replace harness.

4.

CHECK HAZARD SWITCH GROUND CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace hazard switch. Refer to 

EXL-218, "Removal and Installation"

.

NO

>> Repair or replace harness.

Hazard switch

—

Continuity

Connector

Terminal

M45

1

Ground

Existed

EXL-190

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000012201767

EXCEPT FOR NISMO MODELS

Without Daytime Running Light System

NOTE:

Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any

DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp (HI) is not turned 
ON

One side

• Fuse
• Headlamp (HI) power supply/

ground circuit

• Headlamp (HI) bulb
• Headlamp assembly
- Harness
• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-162, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-198, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON
[Headlamp (HI) is turned ON]

Combination meter

• Combination meter

Data monitor “HI-BEAM IND”

• BCM (HEAD LAMP)

Active test “HEAD LAMP”

Headlamp (LO) is not 
turned ON

One side

• Fuse
• Headlamp (LO) power supply/

ground circuit

• Headlamp (LO) bulb

(Xenon bulb)

• Headlamp assembly
- HID control unit
- Xenon bulb socket
- Harness
• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-165, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-199, "Diagnosis Procedure"

.

Each lamp is not turned ON/OFF with lighting switch 
AUTO

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

• Optical sensor power supply/

ground/signal circuit

• Optical sensor
• BCM

Optical sensor
Refer to 

EXL-185, "Component Func-

tion Check"

.

Parking lamp is not turned ON

• Parking lamp power supply/

ground circuit

• Front combination lamp
- LED  (Parking  lamp)
- Harness
• IPDM E/R

Parking lamp circuit
Refer to 

EXL-167, "Component Func-

tion Check"

.

Front side marker lamp is not turned ON

• Front side marker lamp power 

supply/ground circuit

• Front side marker lamp bulb
• Front side marker lamp bulb sock-

et

Front side marker lamp circuit
Refer to 

EXL-169, "Component Func-

tion Check"

.

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-191

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Tail lamp is not turned ON

Stop lamp / Tail lamp 
(Bulb side)

• Fuse
• Tail lamp power supply/ground 

circuit

• Stop lamp / Tail lamp bulb 
• Stop lamp / Tail lamp bulb socket/

harness

• IPDM E/R

Tail lamp circuit
Refer to 

EXL-171, "Component Func-

tion Check"

.

Tail lamp (LED side)

• Fuse
• Tail lamp power supply/ground 

circuit

• Rear combination lamp internal 

circuit

- LED  (Tail  lamp)
• Tail lamp harness
• IPDM E/R

License plate lamp is not turned ON

• License plate lamp power supply/

ground circuit

• License plate lamp bulb
• License plate lamp bulb socket/

harness

License plate lamp circuit
Refer to 

EXL-173, "Component Func-

tion Check"

.

Parking lamp, license plate lamp, side marker lamp and 
tail lamp are not turned ON

Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT 
TURNED ON”
Refer to 

EXL-200, "Diagnosis Procedure"

.

Position lamp indicator is not turned ON
(Parking lamp, license plate lamp, side marker lamp 
and tail lamp are turned ON)

Combination meter

• Combination meter

Data monitor “LIGHT IND”

• BCM (HEAD LAMP)

Active test “TAIL LAMP”

Front fog lamp is not turned 
ON

One side

• Front fog lamp power supply/

ground circuit

• Front fog lamp bulb
• IPDM E/R

Front fog lamp circuit
Refer to 

EXL-180, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-201, "Diagnosis Procedure"

.

Turn signal lamp does not 
blink

Indicator lamp is normal
(Applicable side per-
forms high flasher activa-
tion)

• Front turn signal lamp
- Front turn signal lamp power sup-

ply/ground circuit

- Front turn signal lamp bulb 
- Front turn signal lamp bulb socket
- BCM
• Side turn signal lamp
- Side turn signal lamp power sup-

ply/ground circuit

- Side turn signal lamp
- BCM
• Rear turn signal lamp
- Rear turn signal lamp power sup-

ply/ground circuit

- Rear turn signal lamp bulb 
- Rear turn signal lamp bulb socket/

harness

- BCM

Turn signal lamp circuit
Refer to 

EXL-182, "Component Func-

tion Check"

.

Indicator lamp is included

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Symptom

Possible cause

Inspection item