Nissan Juke F15. Manual - part 741

EXL-184

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

TURN SIGNAL LAMP CIRCUIT

5.

CHECK TURN SIGNAL LAMP BULB

Check the applicable turn signal lamp bulb.
Is the inspection result normal?

YES-1 >> Front turn signal lamp: Check the corresponding front turn signal lamp bulb socket. Repair or

replace if necessary.

YES-2 >> Rear turn signal lamp: Check the corresponding rear turn signal lamp bulb socket and harness.

Repair or replace if necessary.

NO

>> Replace the corresponding turn signal lamp bulb. Refer to 

EXL-211, "Replacement"

 (front turn sig-

nal lamp) or 

EXL-220, "Replacement"

 (rear turn signal lamp).

OPTICAL SENSOR

EXL-185

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

OPTICAL SENSOR

Component Function Check

INFOID:0000000012201763

1.

CHECK OPTICAL SENSOR SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “HEAD LAMP” of “BCM” using CONSULT.

3. Select “OPTI SEN (DTCT)” in “Data Monitor” mode.

4. Turn lighting switch AUTO.

5. With the optical sensor illuminating, check the monitor status. 

*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the inspection result normal?

YES

>> Optical sensor is normal.

NO

>> Refer to 

EXL-185, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201764

1.

CHECK OPTICAL SENSOR POWER SUPPLY

1. Turn ignition switch ON.

2. Turn lighting switch AUTO.

3. Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK OPTICAL SENSOR GROUND

Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 6.

3.

CHECK OPTICAL SENSOR SIGNAL

 With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.

Monitor item

Condition

Voltage

(Approx.)

OPTI SEN (DTCT) Optical sensor

When illuminating

3.1 V or more *

When shutting off light

0.6 V or less

+

-

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

1

Ground

5 V

+

-

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

3

Ground

0 V

EXL-186

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

OPTICAL SENSOR

*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace optical sensor. Refer to 

EXL-216, "Removal and Installation"

.

4.

CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (OPEN)

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (SHORT)

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

6.

CHECK OPTICAL SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

7.

CHECK OPTICAL SENSOR SIGNAL CIRCUIT (OPEN) 

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

+

-

Condition

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

2

Ground

Optical sensor

When illuminating

3.1 V or more*

When shutting off light

0.6 V or less

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

1

M68

17

Existed

Optical sensor

—

Continuity

Connector

Terminal

M84

1

Ground

Not existed

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

3

M68

18

Existed

OPTICAL SENSOR

EXL-187

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace harness.

8.

CHECK OPTICAL SENSOR SIGNAL CIRCUIT (SHORT)

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

2

M68

14

Existed

Optical sensor

—

Continuity

Connector

Terminal

M84

2

Ground

Not existed