Nissan Juke F15. Manual - part 739

EXL-176

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

DAYTIME RUNNING LIGHT RELAY CIRCUIT

5. With operating the test item, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Daytime running light relay circuit is normal.

NO-1 >> Fixed at 0 – 1 V: GO TO 6.

NO-2  >> Fixed at 9 – 16 V: GO TO 5.

5.

CHECK DAYTIME RUNNING LIGHT REQUEST SIGNAL

With CONSULT

1. Select “DTRL REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

2. With operating the daytime running light ON condition, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

6.

CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Remove daytime running light relay.

3. Disconnect IPDM E/R harness connector.

4. Check continuity between IPDM E/R harness connector and daytime running light relay harness connec-

tor.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Repair or replace harness.

Component Inspection

INFOID:0000000012201756

1.

CHECK DAYTIME RUNNING LIGHT RELAY

1. Turn ignition switch OFF.

2. Remove daytime running light relay.

3. Apply battery voltage to daytime running light relay between terminals 1 and 2.

4. Check continuity of daytime running light relay terminals.

Is the inspection result normal?

YES

>> INSPECTION END

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

E13

28

Ground

DAYTIME RUNNING LIGHT

On

0 – 1 V

Off

9 – 16 V

Monitor item

Condition

Monitor status

DTRL REQ

Daytime running light

ON condition

On

OFF condition

Off

IPDM E/R

Daytime running light relay

Continuity

Connector

Terminal

Connector

Terminal

E13

28

E65

2

Existed

Daytime running light relay

Condition

Continuity

Terminal

5

3

Battery voltage

Apply

Existed

Not apply

Not existed

DAYTIME RUNNING LIGHT RELAY CIRCUIT

EXL-177

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

NO

>> Replace daytime running light relay.

EXL-178

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

DAYTIME RUNNING LIGHT CIRCUIT

DAYTIME RUNNING LIGHT CIRCUIT

Component Function Check

INFOID:0000000012201757

1.

CHECK DAYTIME RUNNING LIGHT OPERATION

With CONSULT

1. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

2. With operating the test items, check that the daytime running light is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the daytime running light is turned ON.
Is the measurement normal?

YES

>> Daytime running light circuit is normal.

NO

>> Refer to 

EXL-178, "Diagnosis Procedure"

. 

Diagnosis Procedure

INFOID:0000000012201758

1.

CHECK DAYTIME RUNNING LIGHT FUSE

1. Turn ignition switch OFF.

2. Check that the following fuse is not blown (open).

Is the fuse blown (open)?

YES

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).

NO

>> GO TO 2.

2.

CHECK DAYTIME RUNNING LIGHT POWER SUPPLY

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check the voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

3.

CHECK DAYTIME RUNNING LIGHT POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector and daytime running light connector.

3. Check continuity between IPDM E/R harness connector and daytime running light harness connector.

Fog

: Daytime running light ON

Off

: Daytime running light OFF

Unit

Location

Fuse No.

Capacity

Daytime running light

IPDM E/R

#50

15 A

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

RH

E12

19

Ground

EXTERNAL 
LAMPS

Fog

9 – 16 V

Off

0 – 1 V

LH

20

Fog

9 – 16 V

Off

0 – 1 V

DAYTIME RUNNING LIGHT CIRCUIT

EXL-179

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK DAYTIME RUNNING LIGHT GROUND CIRCUIT

Check continuity between daytime running light harness connector and ground.

Is the inspection result normal?

YES

>> Replace the corresponding daytime running light. Refer to 

EXL-212, "Removal and Installation"

.

NO

>> Repair or replace harness.

IPDM E/R

Daytime running light

Continuity

Connector

Terminal

Connector

Terminal

RH

E12

19

E75

1

Existed

LH

20

E76

Daytime running light

—

Continuity

Connector

Terminal

RH

E75

2

Ground

Existed

LH

E76