Nissan Juke F15. Manual - part 1149

SEC-120

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SECURITY INDICATOR LAMP

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> INSPECTION END

5.

CHECK SECURITY INDICATOR LAMP CIRCUIT

1. Disconnect combination meter connector.

2. Check continuity between combination meter harness connector and BCM harness connector.

3. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

NO

>> Repair or replace harness.

Combination meter

BCM

Continuity

Connector

Terminal

Connector

Terminal

M34

18

M68

23

Existed

Combination meter

Ground

Continuity

Connector

Terminal

M34

18

Not existed

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE

SEC-121

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SYMPTOM DIAGNOSIS

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE

Description

INFOID:0000000012202224

Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.

NOTE:

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

• The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelli-

gent Key system are closely related to each other regarding control. The vehicle security function can oper-

ate only when the door lock and power distribution systems are operating normally.

Conditions of Vehicle (Operating Conditions)

• “ENGINE START BY I-KEY”: ON

Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”

using CONSULT.

• One or more of Intelligent Keys with registered Intelligent Key ID are in the vehicle.

Diagnosis Procedure

INFOID:0000000012202225

1.

PERFORM WORK SUPPORT

Perform “INSIDE ANT DIAGNOSIS” in “Work Support” mode of “INTELLIGENT KEY” of BCM using CON-

SULT.

Refer to 

DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS RESULT

Perform Self-Diagnosis Result in “BCM”, and check whether or not DTC of inside key antenna is detected.
Is DTC detected?

YES

>> Refer to 

BCS-62, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK PUSH-BUTTON IGNITION SWITCH

Check push-button ignition switch.

Refer to 

PCS-78, "Component Function Check"

.

Is the operation normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CONFIRM THE OPERATION

Confirm the operation again.
Is the inspection normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

SEC-122

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

Description

INFOID:0000000012202226

Security indicator lamp does not blink when ignition switch is in a position other than ON.

NOTE:

• Before performing the diagnosis, check “Work Flow”. Refer to 

SEC-44, "Work Flow"

.

• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

Power supply position is not the ON position.

Diagnosis Procedure

INFOID:0000000012202227

1.

CHECK SECURITY INDICATOR LAMP

Check security indicator lamp.

Refer to 

SEC-119, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

VEHICLE SECURITY SYSTEM CANNOT BE SET

SEC-123

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

VEHICLE SECURITY SYSTEM CANNOT BE SET

INTELLIGENT KEY
INTELLIGENT KEY : Description

INFOID:0000000012202228

Armed phase is not activated when all doors are locked using Intelligent Key.

NOTE:

Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON

Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using

CONSULT.

INTELLIGENT KEY : Diagnosis Procedure

INFOID:0000000012202229

1.

CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)

Lock/unlock door with Intelligent Key.

Refer to 

DLK-18, "REMOTE KEYLESS ENTRY FUNCTION : System Description"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check Intelligent Key system (remote keyless entry function). Refer to 

DLK-97, "Diagnosis Proce-

dure"

.

2.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description

INFOID:0000000012202230

Armed phase is not activated when all doors are locked using door request switch.

NOTE:

Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON

Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using

CONSULT.

DOOR REQUEST SWITCH : Diagnosis Procedure

INFOID:0000000012202231

1.

CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)

Lock/unlock door with door request switch.

Refer to 

DLK-14, "DOOR LOCK FUNCTION : System Description"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check Intelligent Key system (door lock function). Refer to 

DLK-93, "ALL DOOR REQUEST

SWITCHES : Diagnosis Procedure"

.

2.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.