Nissan Tiida C11. Manual - part 651

EC-1254

< ECU DIAGNOSIS >

[K9K]

ECM

*: This number is prescribed by ISO 15031-6.

P2502

ALT CHARGE INFO

1

–

–

EC-1205

P2610

ENGINE PROTECTION

1

–

–

EC-1206

DTC*

Items

(CONSULT-III screen item) 

Trip

MI lighting up

Reference page

Yellow

Red

ENGINE CONTROL SYSTEM SYMPTOMS

EC-1255

< SYMPTOM DIAGNOSIS >

[K9K]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

SYMPTOM DIAGNOSIS

ENGINE CONTROL SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000001162698

NOTE:
Only consult this customer complaint after a complete check using the CONSULT-III.

Symptom

Trouble diagnosis

Reference page

No communication with the ECM

CHART 1

EC-1256, "Diag-

nosis Procedure"

Starting malfunction

Engine does not start or starts with difficulty

CHART 2

EC-1257, "Diag-

nosis Procedure"

Starting difficult with cold engine

CHART 3

EC-1259, "Diag-

nosis Procedure"

Impossible to shut off engine

CHART 4

EC-1261, "Diag-

nosis Procedure"

Idle speed malfunction

Engine Idle speed too high

CHART 5

EC-1262, "Diag-

nosis Procedure"

Engine Idle speed too low or unstable

CHART 6

EC-1263, "Diag-

nosis Procedure"

Behavior while driving

Engine stalling

CHART 7

EC-1265, "Diag-

nosis Procedure"

No or very little acceleration, increase in engine speed

CHART 8

EC-1267, "Diag-

nosis Procedure"

Engine bucking

CHART 9

EC-1270, "Diag-

nosis Procedure"

Erratic acceleration

CHART 10

EC-1272, "Diag-

nosis Procedure"

No engine braking

CHART 11

EC-1274, "Diag-

nosis Procedure"

Loss of power

CHART 12

EC-1275, "Diag-

nosis Procedure"

Too much power

CHART 13

EC-1278, "Diag-

nosis Procedure"

Overspeed at idle speed or on releasing brake 

CHART 14

EC-1280, "Diag-

nosis Procedure"

Excessive consumption

CHART 15

EC-1281, "Diag-

nosis Procedure"

Engine knock

CHART 16

EC-1283, "Diag-

nosis Procedure"

Engine overheating

CHART 17

EC-1285, "Diag-

nosis Procedure"

Noise, odors or smoke

Engine smokes when started

CHART 18

EC-1286, "Diag-

nosis Procedure"

Engine emits blue smoke

CHART 19

EC-1287, "Diag-

nosis Procedure"

Engine smokes when revved

CHART 20

EC-1289, "Diag-

nosis Procedure"

Engine emits white smoke (especially when starting)

CHART 21

EC-1290, "Diag-

nosis Procedure"

Emission control not satisfactory

CHART 22

EC-1291, "Diag-

nosis Procedure"

EC-1256

< SYMPTOM DIAGNOSIS >

[K9K]

NOT COMMUNICATION WITH THE ECM

NOT COMMUNICATION WITH THE ECM

Description

INFOID:0000000001162699

CHART 1: NO COMMUNICATION WITH THE ECM

Diagnosis Procedure

INFOID:0000000001162700

1.

INSPECTION START

Ensure that CONSULT-III is not causing the malfunction by trying to establish dialogue with an ECM on
another vehicle. If the CONSULT-III is not at malfunction, and dialogue cannot be established with any other
ECM on the same vehicle, the cause could be a suspected ECM interfering on the CAN communication line.
Check the voltage of the battery and carry out the operations necessary to obtain a voltage which is to specifi-
cation (9.5 V < U battery < 17.5 V).

>> GO TO 2.

2.

CHECK CAN COMMUNICATION

Perform trouble diagnosis on the CAN communication line using CONSULT-III. Refer to 

LAN-33, "CAN Com-

munication Signal Chart"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK ECM GROUND

Check the ECM earth (ground) point on the side strut tower.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace ground connection.

4.

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Check ECM power supply and ground circuit. Refer to 

EC-1106, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness or connector.

5.

CHECK DATA LINK CONNECTOR CIRCUIT

Check for the presence of 12 V on terminal 16 with ignition switch OFF, 12 V on terminal 8 with ignition switch
ON and an earth (ground) on terminals 4 and 5 of the data link connector.
Repair if necessary.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace harness or connector.

ENGINE DOES NOT START OR STARTS WITH DIFFICULTY

EC-1257

< SYMPTOM DIAGNOSIS >

[K9K]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

ENGINE DOES NOT START OR STARTS WITH DIFFICULTY

Description

INFOID:0000000001162701

CHART 2: ENGINE DOES NOT START OR STARTS WITH DIFFICULTY

Diagnosis Procedure

INFOID:0000000001162702

1.

CHECK FUEL

Check that the fuel reservoir is correctly filled and with the right fuel.

>> GO TO 2.

2.

CHECK BATTERY

Check the battery. Refer to 

PG-6, "Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace battery. Refer to 

PG-6, "Removal and Installation"

3.

CHECK STARTER MOTOR

Check the starter and starter motor relay. Refer to 

STR-35, "Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace starter motor or starter relay. Refer to 

STR-35, "Removal and Installation"

4.

CHECK ECM RELAY

Check the ECM relay. Refer to 

EC-1184, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation of IPDM E/R"

.

5.

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Check ECM power supply and ground circuit. Refer to 

EC-1106, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness or connector.

6.

CHECK WIRING HARNESS

Visually check the condition of the engine wiring harness.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness or connector.

7.

CHECK CAMSHAFT POSITION SENSOR 

Check the camshaft position sensor. Refer to 

EC-1152, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace.

8.

CHECK CAMSHAFT 

Check the camshaft. Refer to 

EM-300, "Inspection"

.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Replace camshaft. Refer to 

EM-298, "Removal and Installation"

.

9.

CHECK AIR INTAKE SYSTEM 

Check air intake system. Refer to 

EM-269, "Removal and Installation"

.