Nissan Tiida C11. Manual - part 626

 

  Главная      Nissan     Nissan Tiida C11 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  624  625  626  627   ..

 

 

Nissan Tiida C11. Manual - part 626

 

 

EC-1154

< COMPONENT DIAGNOSIS >

[K9K]

P0380 GLOW RELAY

P0380 GLOW RELAY

DTC Logic

INFOID:0000000001162618

DTC DETECTION LOGIC

NOTE:
• Conditions for applying the diagnostic procedure to the stored DTCs:

The DTC is declared present after attempts have been made to start the engine.

• Special notes:

If the DTC is present, it will be difficult to start the vehicle, or even impossible when cold, or preheating will
be continuous and the heater plugs will deteriorate.

Diagnosis Procedure

INFOID:0000000001162619

1.

CHECK GLOW RELAY POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect glow relay harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between glow relay connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E8, F8
• Harness for open or short between ECM and glow relay
• Harness for open or short between IPDM E/R and glow relay
• Harness for open and short between glow relay and battery

>> Repair open circuit or short to ground or short to power in harness or connectors.

3.

CHECK GLOW RELAY INPUT CIRCUIT FOR OPEN AND SHORT-I

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between glow relay harness connector and ECM harness connector.

4.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

DTC No.

Trouble diagnosis name

Possible cause

P0380

GLOW PLUG DIAGNOSTIC CONNECTION
• CO:  Open  circuit
• CC.0: Short circuit to ground
• CC.1: Short circuit to +12V

• Harness or connectors

(The glow relay circuit is open or shorted.)

• Glow  relay

Glow relay

Ground

Voltage

Connector

Terminal

F55

3

Ground

Battery voltage

Glow relay

ECM

Continuity

Connector

Terminal

Connector

Terminal

F55

9

F11

80

Existed

P0380 GLOW RELAY

EC-1155

< COMPONENT DIAGNOSIS >

[K9K]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4.

CHECK GLOW RELAY OUTPUT CIRCUIT FOR OPEN AND SHORT-II

1.

Check the continuity between glow relay harness connector and ECM harness connector.

2.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-55, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace glow relay.

NO

>> Repair or replace.

Glow relay

ECM

Continuity

Connector

Terminal

Connector

Terminal

F55

8

F11

76

Existed

EC-1156

< COMPONENT DIAGNOSIS >

[K9K]

P0381 GLOW CONTROL SYSTEM

P0381 GLOW CONTROL SYSTEM

DTC Logic

INFOID:0000000001162620

DTC DETECTION LOGIC

NOTE:
• Conditions for applying the diagnostic procedure to the stored DTCs:

The DTC is declared present after several attempts have been made to start the engine.

• Special notes:

If the DTC is present, it will be difficult to start the vehicle, or even impossible when cold, or preheating will
be continuous and the heater plugs will deteriorate.

Diagnosis Procedure

INFOID:0000000001162621

1.

CHECK GLOW RELAY POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect glow relay harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between glow relay connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E8, F8
• Harness for open or short between ECM and glow relay
• Harness for open or short between IPDM E/R glow relay
• Harness for open and short between glow relay and battery

>> Repair open circuit or short to ground or short to power in harness or connectors.

3.

CHECK GLOW RELAY INPUT CIRCUIT FOR OPEN AND SHORT-I

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between glow relay harness connector and ECM harness connector.

4.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

DTC No.

Trouble diagnosis name

Possible cause

P0381

GLOW CONTROL UNIT CIRCUIT
• CC.0: Short circuit to ground
• CO.1: Open circuit or short circuit to +12V

• Harness or connectors

(The glow relay circuit is open or shorted.)

• Glow relay
• Glow  plug

Glow relay

Ground

Voltage

Connector

Terminal

F55

3

Ground

Battery voltage

Glow relay

ECM

Continuity

Connector

Terminal

Connector

Terminal

F55

9

F11

80

Existed

P0381 GLOW CONTROL SYSTEM

EC-1157

< COMPONENT DIAGNOSIS >

[K9K]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4.

CHECK GLOW RELAY OUTPUT CIRCUIT FOR OPEN AND SHORT-II

1.

Check the continuity between glow relay harness connector and ECM harness connector.

2.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

5.

CHECK GLOW RELAY OUTPUT CIRCUIT FOR OPEN AND SHORT

1.

Disconnect glow plug harness connector.

2.

Check the continuity between glow plug harness connector and ECM harness connector.

3.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

6.

CHECK GLOW PLUG 

Refer to 

EC-1157, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace malfunctioning glow plug.

7.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-55, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace glow relay.

NO

>> Repair or replace.

Component Inspection

INFOID:0000000001162622

1.

CHECK GLOW PLUG

1.

Turn ignition switch OFF.

2.

Disconnect glow plug harness connector.

3.

Check resistance between glow plug terminals as follows.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace malfunctioning glow plug.

Glow relay

ECM

Continuity

Connector

Terminal

Connector

Terminal

F55

8

F11

76

Existed

Glow relay

Glow plug

Continuity

Cylinder

Connector

Terminal

Connector

Terminal

1

F55

6

F56

1

Existed

2

7

F57

1

3

1

F58

1

4

2

F59

1

Terminal

Resistance

1 and ground

Not less than 2

 [at 20

°

C (68

°

F)]

 

 

 

 

 

 

 

содержание   ..  624  625  626  627   ..