Nissan Tiida C11. Manual - part 478

EC-562

< COMPONENT DIAGNOSIS >

[HR16DE (WITHOUT EURO-OBD)]

P1572 ASCD BRAKE SWITCH

18.

CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Disconnect ECM harness connector.

2.

Check the continuity between ECM harness connector and stop lamp switch harness connector.

3.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 20.

NG

>> GO TO 19.

19.

DETECT MALFUNCTIONING PART

Check the following.
• Harness for open or short between ECM and stop lamp switch

>> Repair open circuit or short to ground or short to power in harness or connectors.

20.

CHECK STOP LAMP SWITCH

Refer to 

EC-563, "Component Inspection (Stop Lamp Switch)"

.

Is the inspection result normal?

YES

>> GO TO 21.

NO

>> Replace stop lamp switch.

21.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-55, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection (ASCD Brake Switch)

INFOID:0000000001693382

1.

CHECK ASCD BRAKE SWITCH-I

1.

Turn ignition switch OFF.

2.

Disconnect ASCD brake switch harness connector.

3.

Check the continuity between ASCD brake switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ASCD BRAKE SWITCH-II

1.

Adjust ASCD brake switch installation. Refer to 

BR-6, "Inspection and Adjustment"

.

2.

Check the continuity between ASCD brake switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

ECM

Stop lamp switch

Continuity

Connector

Terminal

Connector

Terminal

E16

99

E13 (LHD models)

M203 (RHD models)

2

Existed

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Existed

Slightly depressed

Not existed

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Existed

Slightly depressed

Not existed

P1572 ASCD BRAKE SWITCH

EC-563

< COMPONENT DIAGNOSIS >

[HR16DE (WITHOUT EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

NO

>> Replace ASCD brake switch.

Component Inspection (ASCD Clutch Switch)

INFOID:0000000001693383

1.

CHECK ASCD CLUTCH SWITCH-I

1.

Turn ignition switch OFF.

2.

Disconnect ASCD clutch switch harness connector.

3.

Check the continuity between ASCD clutch switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ASCD CLUTCH SWITCH-II

1.

Adjust ASCD clutch switch installation. Refer to 

CL-5, "On-vehicle Inspection and Adjustment"

.

2.

Check the continuity between ASCD clutch switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace ASCD clutch switch.

Component Inspection (Stop Lamp Switch)

INFOID:0000000001693384

1.

CHECK STOP LAMP SWITCH-I

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp switch harness connector.

3.

Check the continuity between stop lamp switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK STOP LAMP SWITCH-II

1.

Adjust stop lamp switch installation. Refer to 

BR-6, "Inspection and Adjustment"

.

2.

Check the continuity between stop lamp switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch.

Terminals

Condition

Continuity

1 and 2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed

Terminals

Condition

Continuity

1 and 2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Not existed

Slightly depressed

Existed

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Not existed

Slightly depressed

Existed

EC-564

< COMPONENT DIAGNOSIS >

[HR16DE (WITHOUT EURO-OBD)]

P1574 ASCD VEHICLE SPEED SENSOR

P1574 ASCD VEHICLE SPEED SENSOR

Description

INFOID:0000000001693385

The ECM receives two vehicle speed sensor signals via CAN communication line. One is sent from combina-
tion meter, and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD
control. Refer to 

EC-424, "System Diagram"

 for ASCD functions.

DTC Logic

INFOID:0000000001693386

DTC DETECTION LOGIC

NOTE:
• If DTC P1574 is displayed with DTC U1000, U1001, first perform the trouble diagnosis for DTC U1000,

U1001. Refer to 

EC-481, "DTC Logic"

.

• If DTC P1574 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer

to 

EC-482, "DTC Logic"

.

• If DTC P1574 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer

to 

EC-524, "DTC Logic"

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Start engine.

2.

Drive the vehicle at more than 40 km/h (25 MPH).

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.

3.

Check DTC.

Is DTC detected?

YES

>> Go to 

EC-564, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000001693387

1.

CHECK DTC WITH TCM

Check DTC with TCM. Refer to 

TM-32, "OBD Diagnostic Trouble Code (DTC)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Perform trouble shooting relevant to DTC indicated.

2.

CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

P1574

ASCD vehicle speed 
sensor

ECM detects a difference between two vehicle 
speed signals is out of the specified range.

• Harness or connectors

(The CAN communication line is open or 
shorted.)
(Combination meter circuit is open or shorted.)

• Combination meter
• ABS actuator and electric unit (control unit)
• Wheel sensor
• ECM

P1574 ASCD VEHICLE SPEED SENSOR

EC-565

< COMPONENT DIAGNOSIS >

[HR16DE (WITHOUT EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Refer to 

BRC-25, "CONSULT-III Function (ABS)"

 (with ABS) or 

BRC-105, "CONSULT-III Function (ABS)"

 (with

ABS/TCS/ESP).
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace.

3.

CHECK COMBINATION METER

Check combination meter function.
Refer to 

MWI-22, "CONSULT-III Function (METER/M&A)"

.

>> INSPECTION END