Mitsubishi Outlander Sport (2022 year). Manual in english

Combination headlights and dimmer switch

2. Press the AHB switch more than 15 times

[When the sensor is malfunctioning]

Sensor is too hot or cold

within 5 seconds after operation mode is

turned on.

If the system becomes temporarily unavail-

able due to the high or low temperature of the

sensor, the following warning display will

System problem warning

appear.

N00593800072

After the temperature of the sensor has been

If a problem occurs with the system, the fol-

NOTE

in range, the system will automatically return

lowing warning display will appear to the

to operation.

If the sensor or its surrounding area becomes

type of the problem.

extremely high temperature when parking

If the warning display does not disappear

the vehicle under a blazing sun, the “AHB

after waiting for a while, there is a possibility

The AHB deactivation due to fault

SERVICE REQUIRED” warning display

that the AHB has a malfunction. Contact an

may appear.

authorized Mitsubishi Motors dealer for

If a failure is detected in the system, the fol-

If the message remains even after the tem-

inspection of the system.

lowing warning display will appear and the

perature of the sensor or its surrounding area

has been in range, please contact an autho-

AHB will automatically be turned off.

rized Mitsubishi Motors dealer.

If the warning display remains even after the

ignition switch is turned to the “OFF” posi-

tion or the operation mode is put in OFF and

then turned back to ON, please contact an

authorized Mitsubishi Motors dealer.

[When the AHB is malfunctioning]

5-154

Features and controls

Combination headlights and dimmer switch

Windshield is dirty

Welcome light

NOTE

N00563201348

• Push the LOCK button (B) on the remote

If the AHB determines that its performance

This function turns on the front side-marker

control transmitter.

has been degraded, the warning display will

and parking lights for approximately 30 sec-

appear.

onds after the UNLOCK button (A) on the

This can occur when

remote control transmitter is pressed when

the combination headlights and dimmer

z Foreign objects, such as dirt, snow or ice,

switch is in the

“OFF” position

(if so

adhere to the windshield of the sensor

equipped) or “AUTO” position. The welcome

portion.

light function will operate only when it is

z In adverse weather conditions, such as

dark outside the vehicle.

rain, snow, sand storms, etc.

• Turn the combination headlights and dim-

z A front vehicle or an oncoming vehicle is

mer switch to the “

” or “

” position.

splashing water, snow or dirt.

• Turn the ignition switch to the “ON” posi-

tion or put the operation mode in ON.

When the sensor performance returns, the

It is possible to modify functions as follows:

AHB will resume operation.

• The headlights can be set to come on in the

If the warning display does not disappear

low beam setting.

after waiting for a while, there is a possibility

• The welcome light function can be deacti-

that the sensor has a malfunction. Contact an

vated.

authorized Mitsubishi Motors dealer for

For details, consult a Mitsubishi Motors

inspection of the sensor.

dealer.

Coming home light

NOTE

N00547301279

z While the welcome light function is operat-

ing, perform one of the following operations

This function turns on the headlights in the

to cancel the function.

low beam setting for approximately 30 sec-

onds after the ignition switch is turned to the

“OFF” position or the operation mode is put

in OFF.

Features and controls

5-155

Turn signal lever

1. Turn the combination headlights and dim-

4. The headlights will come on in the low

Turn signal lever

mer switch to the “OFF” position (if so

beam setting for approximately 30 sec-

N00522601646

equipped) or “AUTO” position.

onds. After the headlights go off, the

2. Turn the ignition switch to the

“OFF”

headlights can be turned on again in the

When changing lanes, or to making a gradual

position or put the operation mode in

low beam setting for approximately 30

turn, hold the lever in the “lane change” posi-

OFF. Also, if a key was used to start the

seconds by pulling the turn signal lever

tion (1). It will return to the neutral position

engine, remove the key from the ignition

toward you within 60 seconds of turning

when you let go. Use the full position (2)

switch.

the ignition switch to the “OFF” position

when making a normal turn. The lever will

3. Within 60 seconds of turning the ignition

or putting the operation mode in OFF. To

return to the neutral position when the turn is

switch to the “OFF” position or putting

turn on the headlights again after 60 sec-

complete. There may be times when the lever

the operation mode in OFF, pull the turn

onds of turning the ignition switch to the

does not return to the neutral position. This

signal lever toward you.

“OFF” position or putting the operation

usually happens when the steering wheel is

mode in OFF, repeat the process from step

turned only slightly. You can easily return the

lever by hand.

Also, when you move the lever to (1) slightly

then release it, the turn signal lights and the

NOTE

indicator light in the instrument cluster will

While the coming home light function is

flash three times.

operating, perform one of the following

operations to cancel the function.

• Pull the turn signal lever toward you.

• Turn the combination headlights and dim-

mer switch to the “

” or “

” position

or put the operation mode in ON.

• Turn the ignition switch to the “ON” posi-

tion or put the operation mode in ON.

It is possible to modify functions as follows:

• The time that the headlights remain on can

be changed.

• The coming home light function can be

deactivated.

For details, consult a Mitsubishi Motors

dealer.

5-156

Features and controls

Hazard warning flasher switch

NOTE

Hazard warning flasher

Front fog light switch (if so

A light in the instrument panel flashes to

switch

equipped)

show when the front and rear turn signal

N00522700275

N00522801534

lights are working properly.

If this light flashes faster than usual, check

The front fog lights illuminate only when the

for a burned out turn signal light bulb or mal-

headlights are on low beam.

functioning connection in the signal.

Turning the knob in the direction of the “ON”

If the panel light does not come on when the

position turns on the front fog lights as well

lever is moved, check for a blown fuse or a

burned out bulb in the panel.

as the indicator in the instrument cluster. To

Have the system inspected by your autho-

turn them off, turn the knob in the direction of

rized Mitsubishi Motors dealer or a repair

the “OFF” position.

facility of your choice.

The knob will return to the neutral position

It is possible to modify functions as follows:

when it is released.

• Deactivate the turn signal light

3-flash

function for lane changes.

If you press the flasher switch, the front and

• Adjust the time required to operate the

rear turn signals will flash intermittently, and

lever for the 3-flash function.

so will the hazard warning lights. This is an

See your authorized Mitsubishi Motors

emergency warning system and should not be

dealer for details.

used when the vehicle is in motion, except for

emergencies.

If you need to leave your vehicle, the flashers

will keep working after the ignition switch is

removed or the operation mode is put in OFF.

NOTE

z If the flashers are used for several hours, the

NOTE

battery will run down. This could make it

z If the headlights are switched to high beam,

difficult or impossible to restart your vehicle.

the front fog lights will go out; they will illu-

minate again when the headlights are

switched back to low beam.

Features and controls

5-157

Wiper and washer switch

OFF- Off

NOTE

Windshield wipers

AUTO- Auto-wiper control

z If the light switch is rotated to the “OFF”

Rain sensor

position (if so equipped), “AUTO” position

The wipers will automatically

NOTE

(when the headlights are off) or “

” posi-

operate depending on the degree of

tion while the front fog lights are illumi-

z To ensure a clear rearward view, the rear

wetness on the windshield.

nated, they will automatically turn off. They

window wiper will automatically perform

several continuous operations if the selector

LO- Slow

can be turned back on again by rotating the

lever is put in the

“R” position while the

HI- Fast

combination headlights and dimmer switch

windshield wipers are operating.

back to “

” position, and turning the knob

Refer to “Rear window wiper and washer”

Rain sensor

in the direction of the “ON” position.

on page 5-161.

z Do not use fog lights except in conditions of

Can only be used when the ignition switch or

fog, otherwise excessive light glare may

the operation mode is in ON.

temporarily blind oncoming vehicle drivers.

The windshield wipers can be operated with

If the lever is put in the “AUTO” position, the

the ignition switch or the operation mode is in

rain sensor (A) will detect the extent of rain

ON or ACC.

Wiper and washer switch

(or snow, other moisture, dust, etc.) and the

If the blades are frozen to the windshield or

N00523001852

wipers will operate automatically.

rear window, do not operate the wipers until

Keep the lever in the “OFF” position if the

the ice has melted and the blades are freed,

CAUTION

windshield is dirty and the weather is dry.

otherwise the wiper motor may be damaged.

z If the washer is used in cold weather, the

Wiper operation under these conditions can

washer fluid sprayed against the glass may

scratch the windshield and damage the wip-

freeze, which may hinder visibility. Warm

ers.

the glass with the defroster before using the

washer.

MIST- Misting function

The wipers will operate once.

5-158

Features and controls

Wiper and washer switch

CAUTION

NOTE

To adjust the sensitivity of the rain sensor

With the ignition switch or the operation

Do not cover the sensor by affixing a sticker

With the lever in the “AUTO” (rain sensor)

mode in ON and the lever in the “AUTO”

or label to the windshield. Also, do not put

position, it is possible to adjust the sensitivity

position, the wipers may automatically oper-

any water-repellent coating on the wind-

ate in the situations described below.

shield. The rain sensor would not be able to

of the rain sensor by turning the knob (B).

• When cleaning the outside surface of the

detect the extent of rain, and the wipers

windshield, if you touch the rain sensor.

might stop working normally.

• When cleaning the outside surface of the

In the following cases, the rain sensor may

windshield, if you wipe with a cloth the rain

be malfunctioning. Have the vehicle checked

sensor.

at an authorized Mitsubishi Motors dealer or

• When using an automatic car wash.

a repair facility of your choice.

• A physical shock is applied to the wind-

• When the wipers operate at a constant inter-

shield.

val despite changes in the extent of rain.

• A physical shock is applied to the rain sen-

• When the wipers do not operate even

sor.

though it is raining.

If your hands get trapped, you could suffer

The wipers may automatically operate when

injuries or the wipers could malfunction. Be

things such as insects or foreign objects are

sure to turn the ignition switch to the “OFF”

affixed to the windshield on top of the rain

“+”- Higher sensitivity to rain

position or put the operation mode in OFF, or

sensor or when the windshield is frozen.

“-”-

Lower sensitivity to rain

move the lever to the

“OFF” position to

Objects affixed to the windshield will stop

deactivate the rain sensor.

the wipers when the wipers cannot remove

them. To operate the wipers again, move the

NOTE

lever to the “LO” or “HI” position.

z Automatic wiper operation (rain sensitive)

Also, the wipers may operate automatically

NOTE

can be changed to intermittent operation,

due to strong direct sunlight or electromag-

To protect the rubber parts of the wipers, this

either vehicle speed sensitive or not vehicle

netic wave. To stop the wipers, move the

operation of the wipers does not take place

speed sensitive.

lever to the “OFF” position.

when the vehicle is stationary and the ambi-

For further information, please contact your

Contact an authorized Mitsubishi Motors

ent temperature is approximately

°F

authorized Mitsubishi Motors dealer or a

dealer or a repair facility of your choice

(0 °C) or lower, even if the lever is put in the

repair facility of your choice.

when replacing the windshield glass.

“AUTO” position.

Features and controls

5-159

Wiper and washer switch

Misting function

Move the lever in the direction of the arrow

and release, to operate the wipers once.

Use this function when you are driving in

mist or drizzle.

The wipers will operate once if the lever is

raised to the “MIST” position and released

when the ignition switch or the operation

mode is in ON or ACC. The wipers will con-

tinue to operate while the lever is held in the

“MIST” position.

NOTE

Windshield washer

It is possible to modify functions as follows:

N00504601468

• Intelligent washer can be activated.

The windshield washer can be operated with

Refer to

“Intelligent washer” on page

5-160.

the ignition switch or the operation mode is in

• The wipers can be set to operate again after

ON or ACC.

about 6 seconds.

The washer fluid will be sprayed onto the

These functions are not activated when the

windshield by pulling the lever toward you.

vehicle is shipped from the factory.

When the wipers are not in operation or in

To activate or deactivate these functions,

intermittent operation, by pulling the lever

please contact your authorized Mitsubishi

toward you, the wipers will operate several

Motors dealer.

times while the washer fluid is being sprayed.

The wipers will operate once if the lever is

moved to the “AUTO” position and the knob

Intelligent washer

ignition switch or the operation mode is in

By releasing the lever soon after pulling it

ON.

toward you, the washer fluid will be sprayed

several times while the wipers are operating

several times.

5-160

Features and controls

Wiper and washer switch

Intelligent washer will stop operating with

Washer fluid will be sprayed onto the

NOTE

any operation of the lever.

rear window glass while the knob is

z The wiper intermittent operation time can be

turned fully in either direction.

adjusted.

When the washer fluid is sprayed, the

Rear window wiper and washer

See your authorized Mitsubishi Motors

wiper will automatically operate 2 or

N00523201492

dealer for details.

3 times.

The rear window wiper and washer can be

z The washer fluid reservoir is located in the

operated when the ignition switch or the

engine compartment.

operation mode is in ON or ACC.

NOTE

Check the fluid level regularly and refill if

necessary. (Refer to “Washer fluid” on page

The rear window wiper will automatically

9-9.)

Turn the knob

to operate

the rear

window

perform several continuous operations if the

wiper.

selector lever is put in the “R” position while

the windshield wipers or the rear window

Precautions to observe when

wiper is operating.

(automatic operation

mode)

using wipers and washers

After the automatic operation, the rear win-

N00523501307

dow wiper will stop operating if the knob is

in the “OFF” position. If the knob is in the

CAUTION

“INT” position, the rear window wiper will

If the washer is used in cold weather, the

return to the intermittent operation.

washer fluid sprayed onto the glass might

It is possible to set the rear window wiper to

freeze, blocking your view. Heat the glass

perform the automatic operation only if the

with the defroster before using the washer.

selector lever is put in the “R” position while

the rear window wiper is operating with the

knob in the “INT” position.

NOTE

OFF-

Off

See your authorized Mitsubishi Motors

Do not use the wipers when the windshield is

INT-

The wiper operates continuously for

dealer for details.

dry. This could scratch the glass and wear the

several seconds then operates inter-

If the knob is in the “OFF” position, turn the

wiper blades prematurely.

mittently at intervals of approxi-

knob to the “INT” position twice quickly to

Before using the wipers in cold weather,

mately 8 seconds.

operate the rear window wiper continuously.

check to be sure that the wiper blades are not

(continuous operation mode)

frozen to the windshield or rear window.

Turn the knob to the “OFF” position to stop

Using the wipers while the blades are frozen

the rear window wiper continuous operation.

could cause the wiper motor to burn out.

Features and controls

5-161

Electric rear window defogger switch

The indicator light (A) will come on when

NOTE

CAUTION

you press the electric rear window defogger

If the moving wipers become blocked part-

Use the rear window defogger only after the

switch. Electric current will flow through the

way through a sweep by ice or other deposits

engine has started and is running. Be sure to

heating wires on the rear window to help

on the glass, the wipers may temporarily stop

turn the defogger switch off immediately

clear away moisture or frost.

operating to prevent the motor from over-

after the window is clear to save on battery

heating. In this case, park the vehicle in a

power.

safe place, turn the ignition switch to the

Do not place stickers, tape, or other items

“OFF” position or put the operation mode in

that are attached with adhesive over the grid

OFF, and then remove the ice or other depos-

wires on the rear window.

its.

When cleaning the inside rear window, use a

Because the wipers will start operating again

soft cloth and wipe lightly over the grid

after the wiper motor cools down, check that

wires.

the wipers operate before using them.

Avoid using the washer for more than 20 sec-

onds at a time. Do not operate the washer

NOTE

when the washer fluid reservoir is empty or

As your vehicle is equipped with heated mir-

the pump may fail.

rors, mist can also be removed from the out-

During cold weather, add a recommended

side rearview mirrors when the rear window

After approximately 20 minutes of operation,

washer solution that will not freeze in the

defogger switch is pressed. (Refer to “Door

washer fluid reservoir. Otherwise the washer

the system will shut off automatically.

mirror heater” on page 5-51.)

may not work or may be damaged.

To switch the defogger OFF before 20 min-

Replace the wiper blades when they are

utes have passed, press the switch again. The

worn. Use the proper size replacement

indicator light will go out and the defogger

blades. For further information, please con-

will turn off.

tact your authorized Mitsubishi Motors

If you need the defogger for more than

dealer.

20 minutes, press the switch again. This will

add 20 more minutes.

Electric rear window defog-

CAUTION

ger switch

z The rear window defogger is not designed to

N00523701543

melt snow. Remove any snow manually

The rear window defogger can be used when

before using the rear window defogger.

the engine is running.

5-162

Features and controls

Heated steering wheel switch (if so equipped)

Heated steering wheel

Horn switch

N00523801209

switch (if so equipped)

N00589100061

To honk the horn, press around the “

” mark

The heated steering wheel contains internal

on the steering wheel.

heaters in the rim. Heating areas are shown in

the illustration.

WARNING

Persons who are unable to feel tempera-

ture change or skin pain due to age, ill-

ness, injury, medication, fatigue or other

physical conditions or who have sensitive

skin may suffer burns when using the

heated steering wheel. To reduce the risk

of burns, people with such conditions must

Link System

: Heating area

use care when using the heated steering

N00563701213

wheel.

The heated steering wheel can be operated

The Link System takes overall control of the

when the ignition switch or operation mode is

devices connected via the USB input terminal

in ON.

CAUTION

allowing the connected devices to be operated

If water or any other liquid is spilled on the

by using the switches in the vehicle. Refer to

To turn on the heated steering wheel, push the

steering wheel, allow it to dry thoroughly

“USB input terminal” on page 5-163.

heated steering wheel switch. The heated

before attempting to use the heated steering

steering wheel will operate for approximately

wheel. Turn the heated steering wheel off

30 minutes and then it will automatically turn

USB input terminal

immediately if it appears to be malfunction-

off.

ing during use.

N00566701227

The indicator light (A) will illuminate while

Also be aware that using the heated steering

You can connect your USB memory device or

the heated steering wheel is operating.

wheel with the engine off may run the bat-

iPod* to play music files stored in the USB

tery down.

memory device or iPod.

Features and controls

5-163

USB input terminal

*: “iPod” is a registered trademark of Apple

NOTE

Inc. in the United States and other countries.

Type 1

z Use a genuine connector cable from Apple

Inc.

How to connect a USB memory

device

3. Connect the connector cable (A) to the

Type 2

N00566801228

USB input terminal (B).

1. Park your vehicle in a safe place and turn

Type 1

the ignition switch to the “OFF” position

or put the operation mode in OFF.

2. Connect a commercially available USB

connector cable (B) to the USB memory

NOTE

Type 2

device (A).

z Do not connect the USB memory device to

the USB input terminal directly.

The USB memory device may be damaged.

4. To remove the USB connector cable, turn

the ignition switch to the “OFF” position

4. To remove the connector cable, turn the

or put the operation mode in OFF first and

ignition switch to the “OFF” position or

perform the installation steps in reverse.

put the operation mode in OFF first and

perform the installation steps in reverse.

How to connect an iPod

N00566901258

Types of connectable devices

3. Connect the USB connector cable (B) to

1. Park your vehicle in a safe place and turn

the USB input terminal (C).

and supported file specifica-

the ignition switch to the “OFF” position

tions

or put the operation mode in OFF.

N00567001139

2. Connect the connector cable to the iPod.

On vehicles equipped with the Smartphone-

link Display Audio (SDA) or the DISPLAY

AUDIO, refer to the separate owner’s manual

5-164

Features and controls

Sun visors

for details about the types of connectable

devices and supported file specifications.

Sun visors

N00524601422

Pull the sun visor downward (1) to reduce

front glare while driving. To reduce side

glare, turn the visor to the side (2).

CAUTION

z If the lid of vanity mirror with light is kept

Ticket holder

open for prolonged periods of time, the vehi-

cle’s battery will be discharged.

The holder (B) is located on the back of the

sun visor.

Type 2

A vanity mirror is fitted to the back of the sun

visor.

Vanity mirror

Type 1

A vanity mirror is fitted to the back of the sun

visor.

Operating the lid of the vanity mirror will

automatically turn on the mirror light (A).

Features and controls

5-165

12 V power outlets

CAUTION

NOTE

Type 2

z Do not leave plastic cards in the ticket

z If your vehicle is equipped with two 12V

holder. Because the inside of the vehicle will

power outlets, they can be used simultane-

Accessories can be operated in all ignition

become hot if the vehicle is parked in strong

ously.

switch positions or all operation modes.

sunlight, the cards could deform or crack.

Floor console box

Type 1

12 V power outlets

N00525001742

Accessories can be operated while the igni-

tion switch or the operation mode is in ON or

CAUTION

ACC.

Be sure to use a “plug-in” type accessory

operating at

12 V and at 120 W or less.

When using more than one socket at the

Center console

same time, make sure the total power con-

sumption of the electrical accessories does

not exceed 120 W at 12 V.

Also be aware that using electronic equip-

ment with the engine off may run the battery

USB charging outlet (if so

down.

When the power outlet is not in use, be sure

equipped)

to close the power outlet cover or replace the

N00596400040

cap. This will prevent the power outlet from

becoming clogged and short circuiting.

The USB charging outlet can be used as a

power source of the USB appliances when the

WARNING

ignition switch or the operation mode is in

To use a “plug-in” type accessory, open the

The hole next to the power outlet in the

ON or ACC.

cover or remove the cap, and insert the plug

center console is not a cup holder. This

There are two USB charging outlets located

in the power outlet.

hole can be used as a personal compart-

on the back of the floor console box.

ment, but should never be used as a cup

When using the USB charging outlet, connect

holder. Spilling beverages onto the power

the USB connector cable to it.

outlet could cause a short-circuit or an

electric shock.

5-166

Features and controls

HomeLink® Wireless Control System (if so equipped)

(RF) transmitters used to activate devices

CAUTION

such as gate operators, garage door openers,

z Do not use the reversible USB connector

entry door locks, security systems, even home

cable that the USB connector board is

located in the center.

lighting. Additional HomeLink^® information

The USB charging outlet might be damaged.

can be found at www.homelink.com,

z Long use of the electric appliance without

www.youtube.com/HomeLinkGentex, or by

running the engine may run down the bat-

calling the toll-free HomeLink^®-Hotline at 1-

tery.

800-355-3515.

WARNING

NOTE

USB charging outlet (Type-A)

z The USB charging outlet can be used only as

Do not use HomeLink^® with any garage

USB charging outlet (Type-C)

a power source. These are not connected to

door opener that lacks safety stop and

the audio devices of the vehicles.

reverse features as required by U.S. Fed-

z Do not charge many mobile devices together

eral Regulations. A garage door opener

CAUTION

by using a multi-plug adapter of the USB

which cannot detect an object in the path

Insert the USB connector cable in the USB

of a closing garage door and then auto-

charging outlet.

charging outlet firmly.

matically stop and reverse, does not meet

z If water or spill beverages has splashed on

If the USB connector cable does not insert in

current U.S. Federal Regulations. Using a

the USB charging outlet, stop using it and

it firmly, it may become extremely hot and

garage door opener without these features

have the vehicle checked by an authorized

the fuses may blow.

increases the risk of serious injury or

Mitsubishi Motors dealer.

When using USB charging outlet (1), be sure

death.

that the power consumption of the connected

During programming, your garage door

USB device does not exceed 12 W (the peak

or gate may open or close. Make sure that

outlet current or voltage of the USB charging

HomeLink^® Wireless Con-

people and objects are clear of the garage

outlet is DC 5 V-2.4 A). When using USB

door or gate that you are programming.

trol System (if so equipped)

charging outlet (2), be sure that the power

N00554301109

consumption of the connected USB device

does not exceed 15 W (the peak outlet cur-

HomeLink^® and the HomeLink^® house icon

rent or voltage of the USB charging outlet is

are registered trademarks of Gentex Corpora-

DC 5 V-3 A).

The connected devices or the USB charging

tion.

outlet may be damaged.

HomeLink^® provides a convenient way to

replace up to

3 hand-held radio-frequency

Features and controls

5-167

HomeLink® Wireless Control System (if so equipped)

NOTE

Before programming Home-

Once HomeLink^® is programmed, retain the

Link^®

original transmitter for future programming

N00584600032

procedures (for example, new vehicle pur-

Some garage door openers manufactured

chases). Upon sale of the vehicle, the pro-

after 1995 have “rolling code protection”.

grammed HomeLink^® buttons should be

To program a garage door opener

erased for security purposes. Refer to “Clear-

equipped with “rolling code protection”;

ing the programmed information” on page

you will need to access the garage door

5-171.

opener motor to press the motor’s “Learn”

You can program a maximum of 3 devices.

or “Smart” buttons. For convenience, use

To change or replace any of the 3 devices

a ladder and another person to assist you.

after it has been initially programmed, you

It is recommended that a new battery be

NOTE

must first erase the current settings.

placed in the hand-held transmitter of the

You do not need to

continue holding

the

See “Clearing the programmed information”

on page 5-171 or “Reprogramming a single

device being programmed to HomeLink^®

HomeLink^® button.

HomeLink^® button” on page 5-172.

for quicker training and accurate trans-

If the indicator light does not flash, refer to

mission of the radio-frequency signal.

“Clearing the programmed information” on

page 5-171.

Programming a new Home-

2. Position the end of your hand-held trans-

Link^®

mitter (B) 1 to 3 inches (2 to 8 cm) away

N00584700088

from the HomeLink^® button while keep-

To program HomeLink^® to operate a garage

ing the indicator light in view.

door, gate, or entry door opener, home or

office lighting, you need to be at the same

location as the device.

1. Press the HomeLink^® button that you

1- HomeLink® button 1

would like to program. The indicator light

HomeLink^® button 2

(A) will flash orange slowly.

HomeLink^® button 3

5-168

Features and controls

HomeLink® Wireless Control System (if so equipped)

• If the device does not operate, continue

NOTE

with “Programming a new HomeLink^®”

z Some devices may require you to replace this

steps 5 to 7 to complete the program-

“Programming a new HomeLink^®” step 3

ming of a rolling code equipped device.

with procedures noted in the “Gate operator /

5. At the garage door opener receiver

Canadian programming” section. If the indi-

cator light does not change to rapidly flash-

(motor-head unit) in the garage, locate the

ing green or continuously lit green after

“Learn” or “Smart” button. This can usu-

ally be found where the hanging antenna

performing these steps, contact HomeLink^®

at www.homelink.com

wire is attached to the motor-head unit

(see the garage door opener manual to

identify the “Learn” button.)

4. Press the HomeLink^® button that was just

6. Firmly press and release the “Learn” or

NOTE

programmed and observe the indicator

“Smart” button. (The name and color of

Some hand-held transmitters may actually

light.

the button may vary by manufacturer.)

train better from a distance of 6 to 12 inches

• If the indicator light continuously illumi-

There are typically 30 seconds to initiate

(15 to 30 cm). Keep this in mind if you have

nates green, programming is complete

step 7.

difficulty with the programming process.

and your device should operate when the

7. Return to the vehicle and firmly press,

HomeLink^® button is pressed and

hold for 2 seconds and release the pro-

3. Press and hold the hand-held transmitter

released.

grammed HomeLink^® button. Repeat the

button while watching the indicator light

• If the indicator light rapidly flashes

“press/hold/release” sequence a second

(A). Continue pressing the button until the

green, firmly press, hold for 2 seconds

time, and, depending on the brand of the

indicator light (A) changes from slowly

and release the programmed HomeLink^®

garage door opener (or other rolling code

flashing orange to either rapidly flashing

button. Repeat the “press/hold/release”

equipped device), repeat this sequence a

green (rolling code) or continuously lit

sequence a second time, and, depending

third time to complete the programming

green (fixed code). Now you may release

on the brand of the garage door opener

process.

the hand-held transmitter button.

(or other rolling code equipped device),

HomeLink^® should now activate your

repeat this sequence a third time to com-

rolling code equipped device.

plete the programming process. At this

point if your device operates, program-

ming is complete.

Features and controls

5-169

HomeLink® Wireless Control System (if so equipped)

NOTE

z In the event that there are still programming

z If programming a garage door opener or gate

difficulties or questions, additional Home-

operator, it is advised to unplug the device

Link^® information and programming videos

during the “cycling” process to prevent pos-

can be found online at www.homelink.com,

sible overheating.

www.youtube.com/HomeLinkGentex, or by

calling the HomeLink^® Hotline.

3. Press and release

- every

2 seconds

(“cycle”) your hand-held transmitter until the

HomeLink^® indicator light changes from

Gate operator/Canadian pro-

slowly flashing orange to either rapidly flash-

gramming

ing green (rolling code) or continuously lit

1. Within 5 seconds after successfully pro-

green (fixed code). Now you may release the

N00584800034

gramming the garage door opener (refer

hand-held transmitter button.

Canadian radio-frequency laws require trans-

“Programming a new HomeLink^®”

Proceed with “Programming a new Home-

mitter signals to

“time-out” (or quit) after

section), both garage door operation indi-

several seconds of transmission - which may

Link^®” step 4 to complete.

cators (A) will flash rapidly green indicat-

not be long enough for HomeLink^® to pick

ing that the garage door feedback has

up the signal during programming. Similar to

Additional steps for program-

been enabled.

this Canadian law, some U.S. gate operators

If the indicators do not flash, perform

ming a door system with feed-

are designed to “time-out” in the same man-

steps 2 and 3 while pressing the Home-

back

ner.

Link^® button up to the first 10 times after

N00584900035

The indicator LED on the hand-held transmit-

successful programming.

ter will go off when the device times out indi-

The HomeLink^® has the capability of receiv-

2. Press and release the programmed Home-

cating that it has finished transmitting.

ing garage door status from compatible

Link^® button to activate the door. You

If you live in Canada or you are having diffi-

garage door opener systems. Check your

now have 1 minute in which to complete

culties programming a gate operator or

garage door opener manual for the available

step 3.

garage door opener by using the “Program-

feature and HomeLink^® compatibility. Also

ming” procedures, replace “Programming a

for a listing of compatible systems contact

new HomeLink^®” step 3 with the following:

HomeLink^® at: www.homelink.com

5-170

Features and controls

HomeLink® Wireless Control System (if so equipped)

3. Once the door has stopped, press and

The HomeLink^® has the capability of listen-

release the “Learn” or “Smart” button on

ing to these messages at a range up to 820.2

the garage door opener

(refer to your

feet (250 m) (open line of sight), but range

garage door opener owner’s manual for

may be reduced by obstacles such as houses

the location of the “Learn” button). Both

or trees. You may have to slow your vehicle

the HomeLink^® garage door operation

speed to receive the CLOSED or OPENED

indicators will flash rapidly green upon

message feedback from the garage door

successful synchronization with the door

opener. If the unit is out of range before

opener (within 5 seconds).

receiving either the UP or DOWN message

from the door opener, both the UP and

DOWN indicators will flash red followed by

Operating HomeLink^®

The indicators will illuminate/blink

a continuous lit orange indicator in the direc-

N00585000033

response to the following conditions:

tion the door was last moving.

To operate, simply press and release the pro-

Recall of the door state after initial feedback

grammed HomeLink^® button. Activation will

: Blinking

: Illuminates

is possible by simultaneously pressing either

now occur for the trained device (i.e. garage

HomeLink^® buttons 1 and 2 or buttons 2 and

door opener, gate operator, security system,

Garage door opener closing

3 for 2 seconds. The last recorded message

(orange)

entry door lock, home/office lighting, etc.).

will be displayed for 3 seconds, again follow-

For convenience, the hand-held transmitter of

ing the garage door status indication of the

Garage door opener closed

the device may also be used at any time.

(green)

figure above.

Garage door feedback

Out of range

(red)

Clearing the programmed

N00585200035

information

The HomeLink^® has the capability of receiv-

Garage door opener opening

N00585300036

(orange)

ing garage door status from compatible

To erase programming from the 3 buttons

garage door opener systems. Refer to “Addi-

Garage door opener opened

(individual buttons cannot be erased but can

tional steps for programming a door system

(green)

be “reprogrammed” as outlined below), fol-

with feedback” on page 5-170.

low the steps noted:

Garage door status is then displayed with

Out of range

(red)

indicators (A).

Features and controls

5-171

Interior lights

1. Press and hold the 2 outer HomeLink^®

NOTE

CAUTION

buttons for at least 10 seconds. The indi-

z If you do not complete the programming of a

z The transmitter has been tested and complies

cator will change from continuous yellow

new device to the button, it will revert to the

with FCC and IC rules.

to rapidly flashing green.

previously stored programming.

Changes or modifications not expressly

2. Release both buttons.

For questions or comments, visit

approved by the party responsible for com-

www.homelink.com,

pliance could void the user’s authority to

NOTE

www.youtube.com/HomeLinkGentex, or by

operate the device.

z Do not hold for longer than 20 seconds.

calling the HomeLink^® Hotline.

This equipment complies with FCC radiation

exposure limits set forth for an uncontrolled

3. HomeLink^® is now in the train (or learn-

General information

environment. End Users must follow the spe-

ing) mode and can be programmed at any

N00585600071

cific operating instructions for satisfying RF

time beginning with “Programming a new

exposure compliance. This transmitter must

HomeLink^®” step 1.

Your HomeLink^® system operates on a radio

be at least 8 inches (20 cm) from the user and

frequency subject to Federal Communica-

must not be co-located or operating in con-

tions Commission (FCC) Rules (For vehicles

Reprogramming a single

junction with any other antenna or transmit-

sold in U.S.A.) and Industry Canada Rules

ter.

HomeLink^® button

(For vehicles sold in Canada). This device

The term “IC:” before the certification/regis-

N00585400037

complies with Part 15 of the FCC Rules and

tration number only signifies that Industry

RSS- 210 of the Industry Canada Rules.

To reprogram a HomeLink^® button, complete

Canada technical specifications were met.

Operation is subject to the following two con-

the following.

ditions.

1. Press and hold the desired HomeLink^®

Interior lights

z This device may not cause harmful inter-

button. Do not release the button.

N00525301699

ference.

2. The indicator light will begin to slowly

z This device must accept any interference

NOTE

flash orange after 20 seconds. The Home-

that may be received, including interfer-

z Be aware that leaving the light illuminated

Link^® button can be released at this point.

ence that may cause undesired operation.

with the engine off may run the battery

Proceed with

“Programming a new

down.

HomeLink^®” step 2.

Never leave the vehicle without checking

that the light is off.

5-172

Features and controls

Interior lights

• When the remote control transmitter of

Dome light (front)/Reading

the keyless entry system or the F.A.S.T.-

lights

key is used to lock the vehicle.

N00525401472

• If the vehicle is equipped with the

F.A.S.T.-key, when the F.A.S.T.-key is

Dome light (front)

used to lock the vehicle.

NOTE

When the doors other than the driver’s door

and liftgate are closed if the driver’s door is

closed while its lock knob is in the lock posi-

Cargo room light  P.5-174

tion, the light goes off immediately.

Dome light (Rear) (if so equipped) 

When the key was used to start the engine, if

P.5-174

the key is removed while the doors and lift-

Dome light

(Front)/Reading lights



gate are closed, the light is illuminated and

P.5-173

after approximately 30 seconds it goes off.

Sunshade illumination dimming control

When the F.A.S.T.-key was used to start the

switch (if so equipped)  P.5-175

engine, if the operation mode is put in OFF

while the doors and liftgate are closed, the

Center console down light  P.5-176

1- (DOOR)

light illuminates and after approximately 30

The light illuminates when a door or the

seconds it goes off.

liftgate is opened. It goes off approxi-

The time until the light goes off can be

mately 30 seconds after the door or lift-

adjusted. See your authorized Mitsubishi

gate is closed.

Motors dealer for details.

However, the light goes off immediately

in the following cases:

• When the ignition switch is turned to the

The light goes off regardless of whether a

“ON” position or the operation mode is

door or the liftgate is open or closed.

put in ON.

• When the power door lock function is

used to lock the vehicle.

Features and controls

5-173

Interior lights

1- (

)

Reading lights

NOTE

The

light illuminates regardless of

N00537600155

z When the F.A.S.T.-key was used to start the

whether a door or the liftgate is open or

Regardless of the position of the dome light

engine, if the operation mode is put in OFF

closed.

while the doors and liftgate are closed, the

switch, when the lens is pressed, the light on

2- (z )

light illuminates and after approximately 30

the side that was pressed will illuminate.

The light illuminates when a door or the

seconds it goes off.

Press the lens again to turn off the light.

liftgate is opened. It goes off approxi-

z The time until the light goes off can be

mately 30 seconds after the door or lift-

adjusted. See your authorized Mitsubishi

gate is closed.

Motors dealer for details.

However, the light goes off immediately

in the following cases:

3- (

)

• When the ignition switch is turned to the

The light goes off regardless of whether a

“ON” position or the operation mode is

door or the liftgate is open or closed.

put in ON.

• When the power door lock function is

Cargo room light

used to lock the vehicle.

N00526100163

• When the remote control transmitter of

the keyless entry system or the F.A.S.T.-

key is used to lock the vehicle.

• If the vehicle is equipped with the

Dome light (rear) (if so equipped)

F.A.S.T.-key, when the F.A.S.T.-key is

N00525801258

used to lock the vehicle.

NOTE

z When the doors other than the driver’s door

and liftgate are closed if the driver’s door is

closed while its lock knob is in the lock posi-

tion, the light goes off immediately.

z When the key was used to start the engine, if

The light illuminates when

the

liftgate is

the key is removed while the doors and lift-

opened, and goes out when the liftgate is

gate are closed, the light is illuminated and

closed.

after approximately 30 seconds it goes off.

5-174

Features and controls

Mitsubishi Outlander Sport (2022 year). Manual in english - page 11