Content      ..     3      4      5      6     ..

Mitsubishi Outlander (2022 year). Manual in english - page 5

COCKPIT

— Bluetooth® Hands-Free Phone System**

— Voice Recognition system switch**

7.

Wireless charger*

8.

Shift lever

— Continuously Variable Transmission (CVT)

9.

Head-Up Display (HUD) switch*

10.

Power liftgate switch*

11.

Steering wheel

— Horn

*:

if so equipped

**:

See the separate Smartphone-link Display

WAA0192X

1.

Instrument brightness control

4.

Push-button ignition switch

2.

Headlight and turn signal switch/Fog light

5.

Wiper and washer switch

switch*

6.

Steering wheel remote control switches (right

3.

Steering wheel remote control switches

(left

side)

side)

— Cruise control*

— Audio control**

— Adaptive Cruise Control System (ACC)*

— Multi-information display control

— MI-PILOT Assist*

Instruments and controls

2-3

INSTRUMENT PANEL

— Windshield deicer switch*

— Heated seat switch*

— Heated steering wheel switch*

11. USB (Universal Serial Bus) input terminal**

12. Drive mode selector

— Hill Descent Control switch

13. Brake Auto Hold switch

14. Parking brake switch

15. Power outlet

16. Glove box

17. Hazard indicator flasher switch

*:

if so equipped

**:

See the separate Smartphone-link Display

WAA0193X

1.

Side ventilator

— Multi Around Monitor*

2.

Steering wheel paddle shifter

— Bluetooth® Hands-Free Phone System**

3.

Meters and gauges/Clock

7.

Fuse box cover

4.

Head-Up Display (HUD)*

8.

Hood release handle

5.

Center ventilator

9.

Steering wheel lock lever

6.

Audio system** or navigation system**

10.

Heater/air conditioner control

— Rearview camera*

— Defroster switch

2-4

Instruments and controls

METERS AND GAUGES

MODEL WITH COMBINATION

METER CLUSTER / MULTI-

INFORMATION DISPLAY

(Type 1)

The needle indicators may move slightly

after the ignition switch is placed in the

OFF or LOCK position. This is not a

malfunction.

WAA0245X

1.

Tachometer

2.

Warning/indicator lights

3.

Multi-information display

— Distance to empty/Odometer

4.

Speedometer

5.

Engine coolant temperature gauge

6.

Fuel gauge

Instruments and controls

2-5

MODEL WITH FULL DIGITAL

DRIVER DISPLAY (Type 2)

CAUTION

. For cleaning, use a soft cloth, dampened

with water. Never use a rough cloth,

alcohol, benzine, thinner or any kind of

solvent or paper towel with a chemical

cleaning agent. They will scratch or cause

discoloration to the lens.

. Do not spray any liquid such as water on

the meter lens. Spraying liquid may cause

the system to malfunction.

WAA0194X

1.

Tachometer

7.

Engine coolant temperature gauge

2.

Personal display

8.

Fuel gauge

3.

Warning/indicator lights

4.

Multi-information display

— Distance to empty/Odometer

5.

Speedometer

6.

Secondary speedometer

2-6

Instruments and controls

CHANGING THE METER

SCREEN VIEW (model with type

2 display)

For the model with full-screen display, the

meter screen view can be changed to expand the

multi-information display area.

To change the meter screen view:

1. Push the control switch on the left side of

the steering wheel.

2. "Short Cut Menu" appears on the multi-

information display area.

3. Select "Change Meter View" by rotating the

scroll dial

and push scroll dial

to

confirm.

WAC0351X

1.

Tachometer

2.

Engine coolant temperature gauge

3.

Personal Display

4.

Speedometer

5.

Fuel gauge

Instruments and controls

2-7

display will change to “———”.

. If the amount of fuel added is small, the

display just before the ignition switch is

placed in the “OFF” position may continue

to be displayed.

. When driving uphill or rounding curves, the

fuel in the tank shifts, which may momen-

tarily change the display.

Odometer:

The odometer

is displayed in the multi-

information display when the ignition switch is

in the ON position.

JVI1006X

WAC0352X

The odometer displays

the

total

distance

the

Example

Example

vehicle has been driven.

SPEEDOMETER AND OD-

Distance to empty (dte — km or

OMETER

mile)/Odometer

Speedometer

Distance to empty (dte — km or mile):

The speedometer indicates vehicle speed in

The distance to empty (dte)

provides you

miles per hour (MPH) and kilometers per hour

with an estimation of the distance that can be

(km/h).

driven before refueling. The dte is constantly

being calculated, based on the amount of fuel in

Secondary speedometer (models

the fuel tank and the actual fuel consumption.

with type 2 meter)

The display is updated every 30 seconds.

The secondary speedometer indicates vehicle

The dte mode includes a low range warning

speed in kilometers per hour (km/h) and miles

feature. If the fuel level is low, the warning is

per hour (MPH).

displayed on the screen.

When the fuel level drops even lower, the dte

2-8

Instruments and controls

ENGINE COOLANT TEM-

PERATURE GAUGE

The engine coolant temperature gauge indicates

the engine coolant temperature.

The engine coolant temperature is normal when

the gauge points within the zone shown in the

illustration.

The engine coolant temperature will vary with

the outside air temperature and driving condi-

tions.

WAC0606X

WAC0548X

CAUTION

Example

Type 1

. If the gauge indicates the engine coolant

TACHOMETER

temperature is near the hot (H) end of the

The tachometer indicates engine speed in

normal range, reduce vehicle speed to

decrease the temperature.

revolutions per minute (RPM). Do not rev the

engine into the red zone

. If the gauge is over the normal range, stop

the vehicle as soon as safely possible and

let the engine idle.

CAUTION

. If the engine is overheated, continued

operation of the vehicle may seriously

When engine speed approaches the red zone,

damage the engine. (See “If your vehicle

shift to a higher gear or reduce engine speed.

overheats” (P.6-14) for immediate action

Operating the engine in the red zone may cause

required.)

serious engine damage.

WAC0353X

Type 2

Instruments and controls

2-9

FUEL GAUGE

CAUTION

The fuel gauge indicates the approximate fuel

level in the tank when the ignition switch is in

If the vehicle runs out of fuel, the

the ON position.

malfunction indicator light

(MIL) may

The gauge may move slightly during braking,

come on. Refuel as soon as possible. After

turning, accelerating, or going up and down

a few driving trips, the

light should

hills due to movement of fuel in the tank.

turn off. If the light remains on after a few

driving trips, have the vehicle inspected. It

It may take several seconds to stabilize the

is recommended you visit an authorized

display after refilling the tank.

Mitsubishi Motors dealer for this service.

The low fuel warning

appears on the multi-

For additional information, see “Malfunc-

information display when the fuel level in the

tion Indicator Light (MIL)” (P.2-18).

tank is getting low. Refuel as soon as it is

JVI0640X

convenient, preferably before the gauge reads 0

Type 1

(empty).

The arrow,

, indicates the location of the

fuel filler door.

Refuel before the gauge reads the empty (0)

position.

If fuel is added with the ignition switch is in the

ON position, or the amount of the refueled fuel

is small, the remaining fuel display may

incorrectly indicate the fuel level.

There is a small reserve of fuel in the tank when

the fuel gauge reads the empty (0) position.

WAC0354X

Type 2

2-10

Instruments and controls

CONTINUOUSLY VARIABLE

TRANSMISSION (CVT) POSI-

TION INDICATOR

The Continuously Variable Transmission (CVT)

position indicator indicates the shift lever

position when the ignition switch is in the ON

position.

WAC0286X

INSTRUMENT BRIGHTNESS

CONTROL

The instrument brightness control switch can be

operated when the ignition switch is in the ON

position.

Push the + side of the switch to brighten the

meter and instrument panel lights.

Push the - side of the switch to dim the lights.

Instruments and controls

2-11

WARNING LIGHTS, INDICATOR

LIGHTS AND AUDIBLE REMINDERS

Warning/indicator lights (red)

Warning/indicator lights (yellow)

Warning/indicator lights (other)

Active stability control (ASC) warning

Automatic High Beam (AHB) indica-

light

tor light

Brake warning light (red)

Active stability control (ASC) off

Brake Auto Hold indicator light

indicator light

(white)

Brake Auto Hold indicator light

Charge warning light

Anti-lock Braking System (ABS)

(green)

Electric shift control system warning

warning light

Exterior light indicator

light

Forward Collision Mitigation System

Front fog light indicator light (if so

(FCM) OFF warning light

equipped)

Electric parking brake warning light

Electric power steering warning light

High beam indicator light

Electric parking brake warning light

Engine oil pressure warning light

Turn signal/hazard indicator lights

(yellow)

Front seat belt warning light and chime

Low tire pressure warning light

Hands OFF warning light (if so

Malfunction Indicator Light (MIL)

equipped)

Master warning light

Master warning light

Rear Automatic Emergency Braking

SRS airbag warning light

(Rear AEB) system OFF warning light

2-12

Instruments and controls

paired. It is recommended you visit an author-

CHECKING LIGHTS

or

Brake warning light

ized Mitsubishi Motors dealer for this service.

With all doors closed, apply the parking brake,

(red)

(See “Anti-lock Braking System (ABS) warning

fasten the seat belts and place the ignition

light” (P.2-16).)

This light functions for the brake system.

switch in the ON position without starting the

engine. The following lights (if so equipped)

Low brake fluid warning light:

will come on:

WARNING

When the ignition switch is placed in the ON

,

,

or

(red), PARK or

,

position, the brake warning light illuminates,

,

,

Your brake system may not be working

and then turns off. If the light illuminates while

properly if the warning light is on. Driving

The following lights (if so equipped) come on

the engine is running, stop the vehicle and

could be dangerous. If you judge it to be

briefly and then go off:

perform the following:

safe, drive carefully to the nearest service

,

,

,

,

or

,

,

or

1. Check the brake fluid level. If brake fluid is

station for repairs. Otherwise, have your

(red),

(yellow),

necessary, add fluid and have the system

vehicle towed because driving it could be

dangerous.

checked. It is recommended you have this

If any light does not come on or operates in a

service performed by an authorized

Pressing the brake pedal with the engine

way other than described, it may indicate a

Mitsubishi Motors dealer.

(See

“Brake

stopped and/or low brake fluid level may

burned-out bulb and/or a system malfunction. It

increase your stopping distance and brak-

fluid” (P.8-9).)

is recommended you have the system checked

ing will require greater pedal effort as well

by an authorized Mitsubishi Motors dealer.

2. If the brake fluid level is correct, have the

as pedal travel.

warning system checked. It is recommended

WARNING/INDICATOR

If the brake fluid level is below the

you have this service performed by an

minimum or MIN mark on the brake fluid

LIGHTS (red)

authorized Mitsubishi Motors dealer.

reservoir, do not drive until the brake

See also “Multi-information display” (P.2-21).

system has been checked. It is recom-

Anti-lock Braking System (ABS) warn-

mended you visit an authorized Mitsubishi

ing indicator:

Motors dealer for this service.

When the parking brake is released and the

brake fluid level is sufficient, if both the brake

warning light and the Anti-lock Braking System

(ABS) warning light illuminate, it may indicate

the ABS is not functioning properly. Have the

brake system checked, and if necessary re-

Instruments and controls

2-13

warning light illuminates, the chime sounds and

may indicate that the electric parking brake

Charge warning light

the following message is displayed in the multi-

system is not functioning properly. Have the

When the ignition switch is in the ON position,

information display: “When parked apply park-

system checked, and if necessary repaired. It is

the charge warning light illuminates and then

ing brake”.

recommended you visit an authorized

turns off.

Mitsubishi Motors dealer for this service.

When the ignition switch is placed in the OFF

If the light illuminates while the engine is

position, the chime sounds continuously. Ensure

running, it may indicate the charging system is

the parking brake is applied.

Engine oil pressure warning

not functioning properly. Turn the engine off

Have the system checked by an authorized

light

and check the alternator belt. If the belt is loose,

Mitsubishi Motors dealer or a repair facility of

This light warns of low engine oil pressure.

broken, missing or if the light remains on, have

your choice immediately.

When the ignition switch is in the

“ON”

your vehicle serviced immediately. It is recom-

position, the engine oil pressure warning light

mended you visit an authorized Mitsubishi

or

Electric parking brake

illuminates. After starting the engine, the engine

Motors dealer for this service.

oil pressure warning light turns off. This

warning light

indicates that the oil pressure sensors in the

The electric parking brake warning light

CAUTION

engine are operational.

indicates that the electric parking brake system

If the engine oil pressure warning light

is operating.

Do not continue driving if the alternator belt is

illuminates or blinks while the engine is

loose, broken or missing.

When the ignition switch is placed in the ON

running, it may indicate that the engine oil

position, the electric parking brake warning

pressure is low.

light illuminates. When the engine is started and

the parking brake is released, the warning light

Stop the vehicle safely as soon as possible. Stop

Electric shift control system

the engine immediately and call an authorized

turns off.

warning light

Mitsubishi Motors dealer.

If the parking brake is not fully released, the

When the ignition switch is in the ON position,

electric parking brake warning light remains on.

the electric shift control system warning light

Be sure that the electric parking brake warning

CAUTION

illuminates, and then turns off. This indicates

light has turned off before driving.

(See

the electric shift control system is operational.

“Parking brake” (P.5-23).)

. Running the engine with the engine oil

The electric shift control system warning light

pressure warning light illuminated could

If the electric parking brake warning light

illuminates when a malfunction occurs in the

cause serious damage to the engine.

illuminates or flashes while the electric parking

electric shift control system. When the master

brake warning light

(yellow) illuminates, it

2-14

Instruments and controls

fastened.

. The engine oil pressure warning light is not

SRS airbag warning light

designed to indicate a low oil level. The oil

For additional information, refer to “Seat belt

level should be checked using the dipstick.

warning light and chime” (P.1-19).

After placing the ignition switch in the ON

(See “Engine oil” (P.8-6).)

position, the SRS airbag warning light will

illuminate. The SRS airbag warning light will

Hands OFF warning light (if so

turn off after about

7 seconds if the supple-

Front seat belt warning light

equipped)

mental front airbag and supplemental side

When the Lane Keep Assist (LKA) is activated,

airbag, curtain airbag systems and/or preten-

and chime

it monitors the driver’s steering wheel opera-

sioner seat belt are operational.

The light and chime remind you to fasten the

tion. If the steering wheel is not operated or the

seat belts.

If any of the following conditions occur, the

driver takes his/her hands off the steering wheel

front airbag, side airbag, curtain airbag and

The light illuminates whenever the ignition

for a period of time, the warning light

pretensioner systems need servicing.

switch is placed in the ON position, and will

illuminates on the meter panel. If the driver

. The SRS airbag warning light remains on

remain illuminated until the seat belts are

does not operate the steering wheel after the

fastened.

after approximately 7 seconds.

warning light has been illuminated, an audible

. The SRS airbag warning light flashes

The seat belt warning light for the front

alert sounds and the warning flashes in the

intermittently.

passenger will illuminate if the seat belt is not

multi-information display, followed by a quick

fastened when the front passenger’s seat is

brake application to request the driver to take

. The SRS airbag warning light does not

occupied.

control of the vehicle again. (See “Lane Keep

illuminate at all.

Assist (LKA)” (P.5-117).)

It is recommended you visit an authorized

When the vehicle speed exceeds 10 MPH (15

Mitsubishi Motors dealer for these services.

km/h), the light will continue to blink for about

95 seconds until the driver’s seat belt is fastened

Master warning light (red)

Unless checked and repaired, the Supplemental

and the light will blink unless the front

Restraint Systems and/or the pretensioners may

When the ignition switch is in the ON position,

passenger’s seat belts is securely fastened and

not function properly.

the master warning light (red) illuminates if a

the chime will sound for about

95 seconds

warning message appears in the multi-informa-

For additional information, see “Supplemental

unless the front passenger’s seat belt is securely

tion display.

Restraint System (SRS)” (P.1-47).

fastened.

See “Multi-information display” (P.2-21).

When the ignition switch is placed in the ON

position, the chime will sound for about

6

seconds unless the driver’s seat belt is securely

Instruments and controls

2-15

properly. Have the system checked. It is

you visit an authorized Mitsubishi Motors

WARNING

recommended you visit an authorized

dealer for this service.

Mitsubishi Motors dealer for this service. If a

If an ABS malfunction occurs, the anti-lock

If the SRS airbag warning light is on, it could

malfunction occurs in the system, the ASC

function is turned off. The brake system then

mean that the front airbag, side airbag, curtain

function will be canceled but the vehicle is still

operates normally, but without anti-lock assis-

airbag and/or pretensioner systems will not

driveable. For additional information, see “Ac-

tance. (See “Brake system” (P.5-156).)

operate in an accident. To help avoid injury to

tive stability control (ASC)” (P.5-159) of this

yourself or others, have your vehicle checked.

manual.

It is recommended you visit an authorized

Forward Collision Mitigation

Mitsubishi Motors dealer for this service.

System (FCM) OFF warning light

Active stability control (ASC)

When the ignition switch is in the ON position,

off indicator light

WARNING/INDICATOR

the FCM system OFF warning light illuminates.

When the ignition switch is in the ON position,

LIGHTS (yellow)

After starting the engine, the warning light turns

the Active stability control (ASC) off indicator

off.

See also “Multi-information display” (P.2-21).

light illuminates and then turns off.

This light illuminates when the FCM system is

The light comes on when the Active stability

set to OFF on the multi-information display.

Active stability control (ASC)

control (ASC) is turned OFF. This indicates that

If the light illuminates when the FCM system is

warning light

the ASC and traction control system are not

ON, it may indicate that the system is unavail-

When the ignition switch is in the ON position,

operating.

able. See “Forward Collision Mitigation System

the Active stability control (ASC) warning light

(FCM)”

(P.5-126) or

“Predictive Forward

illuminates and then turns off.

or

Anti-lock Braking

Collision Warning (PFCW)” (P.5-135).

The light will blink when the Active stability

System (ABS) warning light

control (ASC) or the traction control system is

When the ignition switch is in the ON position,

Electric power steering warn-

operating, thus alerting the driver that the

the Anti-lock Braking System (ABS) warning

ing light

vehicle is nearing its traction limits. The road

light illuminates and then turns off. This

surface may be slippery.

When the ignition switch is in the ON position,

indicates the ABS is operational.

the electric power steering warning light

If the ASC warning light illuminates while the

If the ABS warning light illuminates while the

illuminates. After starting the engine, the

ASC is on, this light alerts the driver to the fact

engine is running, or while driving, it may

electric power steering warning light turns off.

that the ASC’s fail-safe mode is operating, for

indicate the ABS is not functioning properly.

This indicates the electric power steering is

example the ASC may not be functioning

Have the system checked. It is recommended

operational.

2-16

Instruments and controls

If the electric power steering warning light

The

“Tire Pressure Low

- Add Air”/“Tire

illuminates while the engine is running, it may

Low tire pressure warning light

Pressure Low - Check Cold Tire” warning is

indicate the electric power steering is not

Your vehicle is equipped with a Tire Pressure

active as long as the low tire pressure warning

functioning properly and may need servicing.

Monitoring System (TPMS) that monitors the

light remains illuminated.

Have the system checked. It is recommended

tire pressure of all tires.

For additional information, see “Multi-informa-

that you visit an authorized Mitsubishi Motors

The low tire pressure warning light warns of

tion display” (P.2-21), “Tire Pressure Monitor-

dealer for this service.

low tire pressure or indicates that the TPMS is

ing System (TPMS)” (P.5-6) and “Tire Pressure

When the electric power steering warning light

not functioning properly.

Monitoring System (TPMS)” (P.6-3).

illuminates with the engine running, the power

After the ignition switch is placed in the ON

TPMS malfunction:

assist to the steering will cease operation but

position, this light illuminates for about

1

you will still have control of the vehicle. At this

If the TPMS is not functioning properly, the low

second and turns off.

time, greater steering efforts are required to

tire pressure warning light will flash for

operate the steering wheel, especially in sharp

Low tire pressure warning:

approximately

1

minute when the ignition

turns and at low speeds.

switch is placed in the ON position. The light

If the vehicle is being driven with low tire

will remain on after the 1 minute. Have the

(See “Electric power steering” (P.5-156).)

pressure, the warning light will illuminate. The

system checked. It is recommended you visit an

“Tire Pressure Low - Add Air”/“Tire Pressure

authorized Mitsubishi Motors dealer for this

Low - Check Cold Tire” warning also appears

Electric parking brake warning

service. The “Tire Pressure Low - Add Air”/

in the multi-information display.

light (yellow)

“Tire Pressure Low - Check Cold Tire” warning

When the low tire pressure warning light

does not appear if the low tire pressure warning

When the ignition switch is in the ON position,

illuminates, you should stop and adjust the tire

light illuminates to indicate a TPMS malfunc-

the electronic parking brake warning light

pressure to the recommended COLD tire

illuminates and then turns off.

tion.

pressure shown on the Tire and Loading

The electric parking brake warning light func-

Information placard. The low tire pressure

For additional information, see “Tire Pressure

tions for the electric parking brake system. If

warning light does not automatically turn off

Monitoring System (TPMS)” (P.5-6).

the warning light illuminates, it may indicate

when the tire pressure is adjusted. After the tire

that the electric parking brake system is not

is inflated to the recommended pressure, the

WARNING

functioning properly. Have the brake system

vehicle must be driven at speeds above 16 MPH

checked, and, if necessary, repaired. It is

(25 km/h) to activate the TPMS and turn off the

. If the light does not illuminate with the

recommended that you visit an authorized

low tire pressure warning light. Use a tire

ignition switch placed in the ON position,

Mitsubishi Motors dealer for this service.

pressure gauge to check the tire pressure.

have the vehicle checked. It is recom-

Instruments and controls

2-17

mended you visit an authorized Mitsubishi

recommended you visit an authorized

3 US gallons (11.4 liters) of fuel in the fuel

Motors dealer for this service as soon as

Mitsubishi Motors dealer for these ser-

tank.

possible.

vices.

After a few driving trips, the

light should

If the light illuminates while driving, avoid

Replacing tires with those not originally

turn off if no other potential emission control

sudden steering maneuvers or abrupt

specified by Mitsubishi Motors could affect

system malfunction exists.

braking, reduce vehicle speed, pull off the

the proper operation of the TPMS.

If this indicator light remains on for 20 seconds

road to a safe location and stop the vehicle

and then blinks for 10 seconds when the engine

as soon as possible. Driving with under-

inflated tires may permanently damage the

is not running, it indicates that the vehicle is not

tires and increase the likelihood of tire

CAUTION

ready for an emission control system inspection/

failure. Serious vehicle damage could

maintenance test. (See “Readiness for Inspec-

occur and may lead to an accident and

The TPMS is not a substitute for the

tion/Maintenance (I/M) test” (P.10-33).)

could result in serious personal injury.

regular tire pressure check. Be sure to

Check the tire pressure for all four tires.

Operation:

check the tire pressure regularly.

Adjust the tire pressure to the recom-

If the vehicle is being driven at speeds of

The malfunction indicator light will come on in

mended COLD tire pressure shown on the

less than 16 MPH (25 km/h), the TPMS

one of two ways:

Tire and Loading Information placard to

turn the low tire pressure warning light

may not operate correctly.

Malfunction indicator light on steady — An

OFF. If the light still illuminates while

Be sure to install the specified size of tires

emission control system and/or CVT mal-

driving after adjusting the tire pressure, a

to the four wheels correctly.

function has been detected. It is recom-

tire may be flat or the TPMS may be

mended you visit an authorized Mitsubishi

malfunctioning. If you have a flat tire,

Motors dealer for this service. You do not

repair it with the tire repair kit as soon as

Malfunction Indicator Light

need to have your vehicle towed to the

possible. If no tire is flat and all tires are

properly inflated, it is recommended you

(MIL)

dealer.

consult an authorized Mitsubishi Motors

Malfunction indicator light blinking — An

If the malfunction indicator light comes on

dealer.

engine misfire has been detected which may

steady or blinks while the engine is running, it

If a wheel that not equipped with the

damage the emission control system.

may indicate a potential emission control and/or

TPMS is installed, the TPMS will not

To reduce or avoid emission control system

Continuously Variable Transmission

(CVT)

function and the low tire pressure warning

malfunction.

damage:

light will flash for approximately 1 minute.

1) Do not drive at speeds above 45 MPH

The light will remain on after 1 minute.

The malfunction indicator light may also

(72 km/h).

Have your tires replaced and/or TPMS

illuminate steady if the vehicle runs out of fuel.

system reset as soon as possible. It is

Check to make sure that the vehicle has at least

2-18

Instruments and controls

2) Avoid hard acceleration or deceleration.

Rear Automatic Emergency

Brake Auto Hold indicator

3) Avoid steep uphill grades.

Braking (Rear AEB) system OFF

light (white)

4) If possible, reduce the amount of cargo

being hauled or towed.

warning light

The Brake Auto Hold indicator light (white)

The malfunction indicator light may stop

This light comes on when the ignition switch is

illuminates when the Brake Auto Hold system

blinking and remain on.

placed in the ON position. It turns off after the

is on standby. (See “Brake Auto Hold” (P.5-

Have the vehicle inspected. It is recom-

engine is started.

25).)

mended you visit an authorized Mitsubishi

This light illuminates when the Rear AEB

Motors dealer for this service. You do not

system is turned off in the multi-information

Brake Auto Hold indicator

need to have your vehicle towed to the

display.

light (green)

dealer.

If the light illuminates when the Rear AEB

The Brake Auto Hold indicator light (green)

system is on, it may indicate that the system is

illuminates while the Brake Auto Hold system

CAUTION

unavailable. For additional information, see

is operating. (See “Brake Auto Hold” (P.5-25).)

“Rear Automatic Emergency Braking

(Rear

Continued vehicle operation without having

AEB)” (P.5-146).

Exterior light indicator

the emission control system and/or CVT system

WARNING/INDICATOR

This indicator illuminates when the headlight

checked and repaired as necessary could lead

to poor driveability, reduced fuel economy, and

LIGHTS (other)

switch is turned to the AUTO (if so equipped),

possible damage to the emission control sys-

or

position and the front parking

See also “Multi-information display” (P.2-21).

tem.

lights, tail lights, license plate lights or head-

lights are on. The indicator turns off when these

Automatic High Beam (AHB)

lights are turned off.

Master warning light (yellow)

indicator light (if so equipped)

When the ignition switch is in the ON position,

The Automatic High Beam (AHB) indicator

Front fog light indicator light

the master warning light (yellow) illuminates if

light illuminates when the Automatic High

(if so equipped)

a warning message appears in the multi-

Beam (AHB) system is turned on and it is

The front fog light indicator light illuminates

information display.

operational.

(See

“Automatic High Beam

when the front fog lights are on. (See “Fog light

(AHB)” (P.2-56).)

See “Multi-information display” (P.2-21).

switch” (P.2-59).)

Instruments and controls

2-19

MULTI-INFORMATION DISPLAY

. Navigation - turn by turn

. Indicators and warnings

. Tire pressure information

. Other information

CHANGING THE METER

SCREEN VIEW (model with full-

screen display)

For the model with full-screen display, the

meter screen view can be changed to expand the

multi-information display area. See “Changing

the meter screen view

(model with

type

2

display)” (P.2-7) for how to transform.

WAC0549X

WAC0287X

Example

HOW TO USE THE MULTI-

The multi-information display

is located as

shown above, and it displays the warnings and

INFORMATION DISPLAY

information. The following items are also

The multi-information display can be changed

displayed if the vehicle is equipped with them:

using the buttons scroll dial

,

, and

. Tachometer

located on the steering wheel.

. Speedometer

Scroll dial - rotate to navigate through the items

and push to change or select an item in multi-

. Vehicle settings

information display

. Trip computer information

- go back to the previous menu

. Driver Assistance

- change from one display screen to

. Cruise control system information

the next (i.e. trip, Fuel economy)

. MI-PILOT Assist

. F.A.S.T.-key operation information

. Audio information

Instruments and controls

2-21

Content      ..     3      4      5      6     ..