Content .. 805 806 807 808 ..

Mitsubishi Outlander XL. Manual - part 807

Adjustment
item (scan tool
MB991958
display)

Adjustment item

Adjusting

contents

(scan tool MB991958
display)

Adjusting contents

180sec

180 seconds

Door

unlock

mode

Door lock system

All doors unlock

All the doors are unlocked when the driver's
side door is unlocked.

Dr door unlock

Only the driver's side door is unlocked when
the driver's side door is unlocked. (default)

Auto

door

unlock by P
position

Auto door unlock by
P position function

Disable

Without function (default)

Always enabled

Always with function

P/W unlocked

With function (with power window
unlocked)

Duration of horn
chirp

Horn sounding time
during horn answer
back

Short

0.01 second (default)

Long

0.02 second

Horn chirp by
RKE

Horn chirp by RKE

Not sound horn

No horn answerback function

Lock any time

The horn sounds when the lock button of
keyless entry transmitter is pressed once.

W lock any time

The horn sounds when the lock button of
keyless entry transmitter is pressed twice.
(default)

Tone

alarm

answer back

Adjusts the tone
alarm answer back
function.

Not sound tone alarm

Without function

At keyless key

Sounds when the keyless entry system is
activated.

At keyless

Sounds when KOS is activated (default).

At Both

Sounds when the keyless entry system or
KOS is activated.

Timer lock timer Timer lock period

adjustment

30sec

30 seconds (default)

60sec

60 seconds

120sec

120 seconds

180sec

180 seconds

Duration

pre-

alarm

Adjustment of pre-
alarm continue time

10 sec

10 seconds (default)

6 sec

6 seconds

Alarm

With/without theft-
alarm function

Disable

Without function

Enable

With function (default)

Panic

alarm

switch

With/without panic
alarm function

Disable

Without function

Enable

With function (default)

Fob out of car

With/without KOS
key

exterior

detection function

Disable

Without function (default)

Enable

With function

KOS feature

KOS

function

adjustment

Both enable

All KOS functions are enabled (default).

DoorEntry enable

Only door entry function is enabled.

KEYLESS OPERATION SYSTEM (KOS)

42B-171

ON-VEHICLE SERVICE

Adjustment
item (scan tool
MB991958
display)

Adjustment item

Adjusting

contents

(scan tool MB991958
display)

Adjusting contents

ENG strt enable

Only engine starting function is enabled.

Both disabled

All KOS functions are disabled.

KOS

unlock

disable time

Adjusts the door
unlock

inhibition

period after door
lock is activated.

0sec

0 seconds

3sec

3 seconds (default)

5sec

5 seconds

TIRE PRESSURE SENSOR ID REGISTRATION

M14209100160USA0000010000

When the TPMS transmitter and/or KOS-ECU are replaced,
execute "Tire Pressure Sensor ID Registration." The TPMS
won't function until the "Tire Pressure Sensor ID Registration"
has been complete.

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicle Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

Connect scan tool MB991958 to the data link connector.

Turn the ignition switch to the "ON" position.

Select "Interactive Diagnosis" from the start-up screen.

Select "System select."

Select "Special Function."

Select "Tire Pressure Sensor ID Registration."

Select "4tires ID Reg. (Change tire PRS.)" and start the tire
pressure sensor ID registration.

Register all tire pressure sensor IDs within twenty minutes.

"4 SNSR ID Registration Do you want to start? Note Finish ID
Registration within 20 minutes." is displayed. Then, press
"OK."

Decrease the tire pressure to 174 kPa or less, and register the
TPMS transmitter ID code of each wheel to KOS-ECU.

NOTE:

｠

On completion of the TPMS transmitter ID code registration,
the TPMS transmitter ID code is displayed on the M.U.T.-III
screen.

42B-172

KEYLESS OPERATION SYSTEM (KOS)

ON-VEHICLE SERVICE

｠

It may take approximately one minute for the ID code to be
displayed on the M.U.T.-III screen after the tire pressure is
reduced.

｠

If the ID code is not displayed, reduce the tire pressure
another 20 kPa or more. If the ID code is not displayed yet,
rotate the tire to displace the TPMS transmitter, and reduce
the tire pressure 20 kPa or more again.

｠

You can start out the following operations from any TPMS
transmitter. The tire pressure sensor ID registration has no
order.

10.

"4 SNSR ID Registration Completed." is displayed. Then,
select "OK."

NOTE:

The TPMS indicator illuminates for tire pressure

alarm.

11.

After tire pressure sensor ID registration, turn the ignition
switch to the "LOCK" (OFF) position.

12.

Remove scan tool MB991958.

TIRE PRESSURE SENSOR CHECK

M14209100161USA0000010000

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicle Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A

Check the condition of the tire pressure sensor as described
below.

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

Connect scan tool MB991958 to the data link connector.

Turn the ignition switch to the "ON" position.

Select "Interactive Diagnosis" from the start-up screen.

Select "System select."

Select "Special Function."

Select "Tire Pressure Sensor Check."

"Tire Pressure Sensor Check. Do you want to start?" is
displayed. Then, select "OK."

Change the pressure of tire to be checked for 20 kPa or more.
(The tire pressure can either be decreased or increased.)

Check the data on the PC display.

NOTE:

｠

It may take approximately one minute for the ID code to be
displayed on the M.U.T.-III screen after the tire pressure is
changed.

KEYLESS OPERATION SYSTEM (KOS)

42B-173

ON-VEHICLE SERVICE

｠

If the ID code is not displayed, change the tire pressure
another 20 kPa or more. If the ID code is not still displayed,
rotate the tire to displace the TPMS transmitter, and change
the tire pressure 20 kPa or more again.

10.

After tire pressure sensor check, turn the ignition switch to
the "LOCK" (OFF) position.

11.

Remove scan tool MB991958.

TIRE PRESSURE SENSOR ID CHECK

M14209100162USA0000010000

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicle Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A

Check the tire pressure sensor IDs, which is registered in the
TPMS receiver, as described below.

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

Connect scan tool MB991958 to the data link connector.

Turn the ignition switch to the "ON" position.

Select "Interactive Diagnosis" from the start-up screen.

Select "System select."

Choose "TPMS" from the "CHASSIS" tab.

Select "MITSUBISHI."

Select "Special Function."

Select "Tire Pressure Sensor ID Check."

Check the tire pressure sensor IDs on the PC display.

10.

After tire pressure sensor ID check, turn the ignition switch
to the "LOCK" (OFF) position.

11.

Remove scan tool MB991958.

FROM SCAN TOOL MB99158 DIAGNOSIS SCREEN
You can check the tire pressure sensor ID on the diagnosis
screen as described below.

Operate scan tool MB991958 as follows:

｠

Press "Special" button on the diagnosis screen.

｠

Select "Tire Pressure Sensor ID Check" from the "Special
Function" menu.

Check the tire pressure sensor IDs on the PC display.

After tire pressure sensor ID check, turn the ignition switch to
the "LOCK" (OFF) position.

Remove scan tool MB991958.

42B-174

KEYLESS OPERATION SYSTEM (KOS)

ON-VEHICLE SERVICE

Content .. 805 806 807 808 ..