Mitsubishi Outlander GS45X. Manual - part 753

 

  Index      Mitsubishi     Mitsubishi Outlander GS45X - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  751  752  753  754   ..

 

 

Mitsubishi Outlander GS45X. Manual - part 753

 

 

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>

13A-835

10

Air Flow Rate from Mass Air 
Flow Sensor

MAF: xxxx.xx g/s (xxxx.x 
lb/min)

See M.U.T.-III item No. AA.

11

Absolute Throttle Position

TP: xxx.x%

See M.U.T.-III item No. AB.

13

Location of Oxygen 
Sensors

O2SLOC: O2Sxx

Ignition switch: "ON"

O2S11/O2
S12

15

Bank 1 

− Sensor 2

O2S12: x.xxx V

See M.U.T.-III item No. AD.

1C

OBD requirements to which 
vehicle or engine is certified

OBDSUP: OBD II

Ignition switch: 
"ON"

OBD II

1F

Time Since Engine Start

RUNTM: xxxxx sec.

21

Distance Traveled While 
MIL is Actived

MIL_DIST: xxxxx km (xxxxx 
miles)

24

Bank 1 

− Sensor 1 (wide 

range O2S)

LAMBDA11: xxx.xxx

See M.U.T.-III item No. E0.

O2S11: xxx.xxx V

See M.U.T.-III item No. E1.

2C

Commanded EGR

EGR_PCT: xxx.x%

See M.U.T.-III item No. BA.

2E

Commanded Evaporative 
Purge

EVAP_PCT: xxx.x%

See M.U.T.-III item No. 49.

2F

Fuel Level Input

FLI: xxx.x%

See M.U.T.-III item No. 51.

30

Number of warm-ups since 
DTCs cleared

WARM_UPS: xxx

31

Distance traveled since 
DTCs cleared

CLR_DIST: xxxxx km 
(xxxxx miles)

32

Evap System Vapor 
Pressure

EVAP_VP: xxxx.x Pa 
(xx.xxx in H2O)

• Ignition switch: "ON"

• Fuel cap removal

−3.3 to 3.3 

kPa 
(

−13.2 to 

13.2 
in.H2O)

33

Barometric Pressure

BARO: xxx kPa (xx.x inHg) See M.U.T.-III item No. BB.

PARAMETER 
IDENTIFICATI
ON (PID)

DESCRIPTION

COMMON EXAMPLE OF GENERAL 
SCAN TOOL DISPLAY

INSPECTION 
CONDITION

NORMAL 
CONDITION

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>

13A-836

41

Monitor status this driving cycle

Enable status of continuous 
monitors this monitoring 
cycle:

Enable status of continuous 
monitors this monitoring 
cycle: NO means disable 
for rest of this monitoring 
cycle or not supported in 
PID 01, YES means enable 
for this monitoring cycle.

Misfire monitoring enabled

MIS_ENA: NO or YES

Fuel system monitoring 
enabled

FUEL_ENA: NO or YES

Comprehensive component 
monitoring enabled

CCM_ENA: NO or YES

Completion status of 
continuous monitors this 
monitoring cycle:

Completion status of 
continuous monitors this 
monitoring cycle:

Misfire monitoring 
completed

MIS_CMPL: YES or NO

Fuel system monitoring 
completed

FUELCMPL: YES or NO

Comprehensive component 
monitoring completed

CCM_CMPL: YES or NO

Enable status of 
non-continuous monitors 
this monitoring cycle:

Enable status of 
non-continuous monitors 
this monitoring cycle:

Catalyst monitoring

CAT_ENA: YES

Heated catalyst monitoring HCAT_ENA: NO
Evaporative system 
monitoring

EVAP_ENA: YES

Secondary air system 
monitoring

AIR_ENA: NO

Oxygen sensor monitoring

O2S_ENA: YES

Oxygen sensor heater 
monitoring

HTR_ENA: YES

EGR and/or VVT system 
monitoring

EGR_ENA: YES

Completion status of 
non-continuous monitors 
this monitoring cycle:

Completion status of 
non-continuous monitors 
this monitoring cycle:

PARAMETER 
IDENTIFICATI
ON (PID)

DESCRIPTION

COMMON EXAMPLE OF GENERAL 
SCAN TOOL DISPLAY

INSPECTION 
CONDITION

NORMAL 
CONDITION

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>

13A-837

41

Catalyst monitoring 
completed

CAT_CMPL: YES or NO

Heated catalyst monitoring 
completed

HCATCMPL: YES

Evaporative system 
monitoring completed

EVAPCMPL: YES or NO

Secondary air system 
monitoring completed

AIR_CMPL: YES

Oxygen sensor monitoring 
completed

O2S_CMPL: YES or NO

Oxygen sensor heater 
monitoring completed

HTR_CMPL: YES or NO

EGR and/or VVT system 
monitoring completed

EGR_CMPL: YES or NO

42

Control module voltage

VPWR: xx.xx V

See M.U.T.-III item No. 1.

43

Absolute Load Value

LOAD_ABS: xxxxx.x %

See M.U.T.-III item No. 72.

44

Fuel/Air Commanded 
Equivalence Ratio

LAMBDA: xxx.xxx

Engine: running

• "1" means 

"stoichiometric air 
fuel ratio". The 
smaller air fuel 
ratio, the rich 
return. The more 
air fuel ratio, the 
lean return.

− 1.999

(Display 
range)

45

Relative Throttle Position

TP_R: xxx.x%

See M.U.T.-III item No. BC.

46

Ambient air temperature

AAT: xxx

°C (xxx°F)

• Ignition 

switch: "ON"

• Engine is 

cold state

The value 
displayed 
approxima
tely 
matches 
the 
ambient 
temperatu
re

47

Absolute Throttle Position B TP_B: xxx.x%

See M.U.T.-III item No. BD.

49

Accelerator Pedal Position 
D

APP_D: xxx.x%

See M.U.T.-III item No. BE.

4A

Accelerator Pedal Position 
E

APP_E: xxx.x%

See M.U.T.-III item No. BF.

4C

Commanded Throttle 
Actuator Control

TAC_PCT: xxx.x%

See M.U.T.-III item No. 58.

5A

Relative Accelerator Pedal 
Position

APP_R: xxx.x%

See M.U.T.-III item No. DD.

PARAMETER 
IDENTIFICATI
ON (PID)

DESCRIPTION

COMMON EXAMPLE OF GENERAL 
SCAN TOOL DISPLAY

INSPECTION 
CONDITION

NORMAL 
CONDITION

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>

13A-838

ACTUATOR TEST REFERENCE TABLE

M1131152503063

NOTE: *: Continues for 27 minutes. Can be released by pressing the CLEAR key.

M.U.T.-III 
SCAN TOOL 
DISPLAY

ITEM 
NO.

INSPECTION 
ITEM

DRIVE 
CONTENTS

INSPECTION 
REQUIREMENT

NORMAL 
CONDITION

INSPECTION 
PROCEDURE 
NO.

REFERENCE 
PAGE

A/C relay

16

A/C 
compressor 
clutch relay

A/C 
compressor 
clutch relay 
turns from 
OFF to ON.

Ignition switch: 
"ON"

Clicks when 
A/C 
compressor 
clutch is 
driven.

Procedure 
No. 26

P.13A-812

Cooling fan 14

Radiator fan, 
A/C condenser 
fan 

Drive the 
fan motor.

Ignition switch: 
"ON"

Radiator 
fan and A/C 
condenser 
fan rotate.

EVAP. 
emission 
purge SOL. 
Valve

10

Evaporative 
emission purge 
solenoid

Solenoid 
valve turns 
from OFF to 
ON.

Ignition switch: 
"ON"

Clicks when 
solenoid 
valve is 
driven.

Code No. 
P0443

P.13A-419

EVAP. 
emission 
ventilation 
SOL.

15

Evaporative 
emission 
ventilation 
solenoid

Solenoid 
valve turns 
from OFF to 
ON.

Ignition switch: 
"ON"

Clicks when 
solenoid 
valve is 
driven.

Code No. 
P0446

P.13A-426

Fuel pump

9

Fuel pump

Fuel pump 
operates 
and fuel is 
recirculated
.

Ignition 
switch: 
"ON"

Listen 
near 
the fuel 
tank for 
the 
sound 
of fuel 
pump 
operati
on.

Sound of 
operation is 
heard.

Procedure 
No. 23

P.13A-788

 

 

 

 

 

 

 

Content   ..  751  752  753  754   ..