Mitsubishi Outlander (2013+). Manual - part 685

RADIO AND CD PLAYER

CHASSIS ELECTRICAL

54A-225

YES : 

Replace the radio and CD player.

NO : 

A poor connection, open circuit or other 
intermittent malfunction in the CAN bus line 
between the radio and CD player and the 
KOS-ECU. (Refer to GROUP 00 

− How to 

Use Troubleshooting/Inspection Service 
Points - How to Cope with Intermittent 
Malfunction .)

Code No.U0230 Power Gate CAN Timeout

CAUTION

• If diagnosis code No. U0230 is set, be sure to 

diagnose the CAN bus line.

• When replacing the radio and CD player, 

always check that the communication circuit 
is normal.

DIAGNOSTIC FUNCTION

If the signal from electric tailgate control unit cannot 
be received, the radio and CD player sets the diag-
nosis code No. U0230.

JUDGEMENT CRITERIA

With the statuses that the ignition switch is at ON 
position, system voltage is 10 

− 16 V (data from 

ETACS-ECU), and there is no malfunction to the 
power supply fuse (IOD fuse), or odometer value is 
80.5 km or more, if the communication with electric 
tailgate control unit cannot be established for 2,500 
ms or more, the radio and CD player determines that 
a problem has occurred.

PROBABLE CAUSES

• Malfunction of CAN bus line

• Malfunction of electric tailgate control unit

• Malfunction of radio and CD player

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.

Q: Is the check result normal?

YES : 

Go to Step 2.

NO : 

Repair the CAN bus line (Refer to GROUP 
54C 

− Troubleshooting ).

STEP 2. M.U.T.-III other system diagnosis code
Check again if the diagnosis code is set to the elec-
tric tailgate control unit.

Q: Is the diagnosis code set?

YES : 

Troubleshoot the electric tailgate control unit 

(Refer to GROUP 42A 

− Tailgate <vehicles 

with electric tailgate> 

− Diagnosis Code 

Chart ), and then go to Step 3.

NO : 

Go to Step 3.

STEP 3. Check the M.U.T.-III Diagnosis code for 
other systems
Check if the diagnosis code No. U0230 is set to 
ETACS-ECU.

Q: Is the diagnosis code set?

YES : 

Go to Step 4.

NO : 

Go to Step 5.

STEP 4. Diagnosis code recheck
Check again if the diagnosis code is set to the radio 
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF) 

position to the "ON" position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the electric tailgate control unit.

NO : 

A poor connection, open circuit or other 
intermittent malfunction in the CAN bus line 
between the radio and CD player and the 
electric tailgate control unit. (Refer to 
GROUP 00 

− How to Use 

Troubleshooting/Inspection Service Points - 
How to Cope with Intermittent Malfunction .)

STEP 5. Check whether the diagnosis code is 
reset.
Check again if the diagnosis code is set to the radio 
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF) 

position to the "ON" position.

(3) Check if diagnosis code is set.

Q: Is the diagnosis code set?

RADIO AND CD PLAYER

CHASSIS ELECTRICAL

54A-226

YES : 

Replace the radio and CD player.

NO : 

A poor connection, open circuit or other 
intermittent malfunction in the CAN bus line 
between the radio and CD player and the 
electric tailgate control unit. (Refer to 
GROUP 00 

− How to Use 

Troubleshooting/Inspection Service Points - 
How to Cope with Intermittent Malfunction .)

Code No.U1000 OSS CAN timeout

CAUTION

• If diagnosis code No. U1000 is set, be sure to 

diagnose the CAN bus line.

• When replacing the radio and CD player, 

always check that the communication circuit 
is normal.

DIAGNOSTIC FUNCTION

If the signal from OSS-ECU cannot be received, the 
radio and CD player sets the diagnosis code No. 
U0230.

JUDGEMENT CRITERIA

With the statuses that the ignition switch is at ON 
position, system voltage is 10 

− 16 V (data from 

ETACS-ECU), and there is no malfunction to the 
power supply fuse (IOD fuse), or odometer value is 
80.5 km or more, if the communication with 
OSS-ECU cannot be established for 2,500 ms or 
more, the radio and CD player determines that a 
problem has occurred.

PROBABLE CAUSES

• Malfunction of CAN bus line

• Malfunction of OSS-ECU

• Malfunction of radio and CD player

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.

Q: Is the check result normal?

YES : 

Go to Step 2.

NO : 

Repair the CAN bus line (Refer to GROUP 
54C 

− Troubleshooting ).

STEP 2. M.U.T.-III other system diagnosis code
Check again if the diagnosis code is set to the 
OSS-ECU.

Q: Is the diagnosis code set?

YES : 

Troubleshoot the OSS-ECU (Refer to 

GROUP 42B 

− Diagnosis Code Chart ), and 

then go to Step 3.

NO : 

Go to Step 3.

STEP 3. Check the M.U.T.-III Diagnosis code for 
other systems
Check if the diagnosis code No. U1000 is set to 
ETACS-ECU.

Q: Is the diagnosis code set?

YES : 

Go to Step 4.

NO : 

Go to Step 5.

STEP 4. Diagnosis code recheck
Check again if the diagnosis code is set to the radio 
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF) 

position to the "ON" position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code set?

YES : 

Replace the OSS-ECU.

NO : 

A poor connection, open circuit or other 
intermittent malfunction in the CAN bus line 
between the radio and CD player and the 
OSS-ECU. (Refer to GROUP 00 

− How to 

Use Troubleshooting/Inspection Service 
Points - How to Cope with Intermittent 
Malfunction .)

STEP 5. Check whether the diagnosis code is 
reset.
Check again if the diagnosis code is set to the radio 
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF) 

position to the "ON" position.

(3) Check if diagnosis code is set.

Q: Is the diagnosis code set?

RADIO AND CD PLAYER

CHASSIS ELECTRICAL

54A-227

YES : 

Replace the radio and CD player.

NO : 

A poor connection, open circuit or other 
intermittent malfunction in the CAN bus line 
between the radio and CD player and the 
OSS-ECU. (Refer to GROUP 00 

− How to 

Use Troubleshooting/Inspection Service 
Points - How to Cope with Intermittent 
Malfunction .)

Code No.U1190 No receive fault detect signal

CAUTION

• Before replacing the ECU, ensure that the 

power supply circuit, the earth circuit and the 
communication circuit are normal.

• When the ETACS-ECU of vehicles without 

KOS is replaced, the encrypted code of the 
ignition key needs to be registered to the 
ETACS-ECU. (If the encrypted code is not reg-
istered, the engine cannot be started. Regis-
ter the encrypted code as described in 
Immobilizer System 

− How to Register Key ID 

P.54A-33

.)

JUDGEMENT CRITERIA

ETACS-ECU sends the diagnosis code (U code) 
detection permission or prohibition signal to each 
ECU connected to the CAN bus line. If the radio and 
CD player cannot receive the diagnosis code (U 
code) detection permission or prohibition signal for 5 
seconds after turning the electric motor switch to ON 
position, diagnosis code U1190 will be set.

PROBABLE CAUSES

• Malfunction of the ETACS-ECU

• Malfunction of CAN bus line

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.

Q: Is the check result normal?

YES : 

Go to Step 2

NO : 

Repair the CAN bus line (Refer to GROUP 
54C 

− Troubleshooting ). On completion, go 

to Step 3.

STEP 2. Check whether the diagnosis code is 
reset.
Check again if the diagnosis code is set to the radio 
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF) 

position to the "ON" position.

(3) On completion, check that the diagnosis code is 

reset.

Q: Is the diagnosis code set?

YES : 

Replace the ETACS-ECU. Then go to Step 

3.

NO : 

The procedure is complete.

STEP 3. Check whether the diagnosis code is 
reset.
Recheck if the diagnosis code is set to the radio and 
CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF) 

position to the "ON" position.

(3) On completion, check that the diagnosis code is 

reset.

Q: Is the diagnosis code set?

YES : 

Return to Step 1.

NO : 

The procedure is complete.

RADIO AND CD PLAYER

CHASSIS ELECTRICAL

54A-228

Code No. U1195 Coding not completed

CAUTION

• If the diagnosis code No. U0164 is set, be sure 

to diagnose the CAN bus line.

• When replacing the radio and CD player, 

always check that the communication circuit 
is normal.

• When the diagnosis code No.U1195 is set in 

radio and CD player, the diagnosis code may 
also be set in ETACS-ECU. When the diagno-
sis code is set in ETACS-ECU, carry out the 
diagnosis of the diagnosis code for 
ETACS-ECU first.

JUDGEMENT CRITERIA

This diagnosis code is set when the variant coding 
for ETACS-ECU has not been implemented.

PROBABLE CAUSES

• Variant coding for ETACS-ECU has not been 

implemented.

• Malfunction of radio and CD player

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnosis
Use M.U.T.-III to diagnose the CAN bus lines.

Q: Is the check result normal?

YES : 

Go to Step 2.

NO : 

Repair the CAN bus lines (Refer to GROUP 
54C 

− CAN Bus Diagnostics Table ). On 

completion, go to Step 4.

STEP 2. M.U.T.-III other system diagnosis code
Use M.U.T.-III to check that the diagnosis code 
No.B222C is set in the ETACS-ECU.

Q: Is the diagnosis code set?

YES : 

Troubleshoot the relevant diagnosis code, 

and then go to Step 4.

NO : 

Go to Step 3.

STEP 3. Check whether the diagnosis code is 
reset.
Check again if the diagnosis code is set to the radio 
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF) 

position to the "ON" position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code No.U1195 set?

YES : 

Replace the radio and CD player, and then 

go to Step 4.

NO : 

Intermittent malfunction (Refer to GROUP 
00 

− How to Use Troubleshooting/How to 

Cope with Intermittent Malfunctions ).

STEP 4. Check whether the diagnosis code is 
reset.
Check again if the diagnosis code is set to the radio 
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF) 

position to the "ON" position.

(3) Check if the diagnosis code is set.

Q: Is the diagnosis code No.U1195 set?

YES : 

Return to Step 1.

NO : 

This diagnosis is complete.

TROUBLE SYMPTOM CHART

M1544004902769

Trouble symptom

Inspection 
Procedure No.

Reference 
page

Power of the radio and tape player does not turn ON when the ignition switch 
is in the "ACC" position or "ON" position.

1

P.54A-229

No sound is heard.

2

P.54A-230

The radio broadcasting can not be received.

3

P.54A-231

Audio illumination does not work normally.

4

P.54A-232

NOTE: 

.

•

For the troubleshooting of the hands free-ECU, 
refer to 

P.54A-257

.<Vehicles with display audio>

•

For the troubleshooting of the steering wheel 
audio remote control switch, refer to 

P.54A-243

.<Vehicles with display audio>