Jeep Grand Cherokee WJ. Manual - part 679

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  677  678  679  680   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 679

 

 

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the Water In Fuel Sensor harness connector.
Measure the resistance between Sensor Ground and the Water In Fuel Sensor Signal
circuit.
Is the resistance above 100 kohms?

All

Yes

Replace and program the PCM in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Repair the Water In Fuel Sensor Signal circuit for a short to the
Sensor Ground circuit.
Perform ROAD TEST VERIFICATION - VER-2.

5

Turn the ignition off.
Disconnect the Water In Fuel Sensor harness connector.
Turn the ignition on.
Connect a jumper wire across the Water In Fuel Sensor harness connector cavities 1
and 2.
Observe the Water In Fuel Lamp for at least 30 seconds.
Is the lamp on?

All

Yes

Replace the Water In Fuel Sensor.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

6

6

Turn the ignition off.
Disconnect the Water In Fuel Sensor harness connector.
Disconnect the PCM harness connectors.
Measure the resistance of the Water In Fuel Sensor Signal circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

7

No

Repair the Water In Fuel Sensor Signal circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

7

Turn the ignition off.
Disconnect the Water In Fuel Sensor harness connector.
Disconnect the PCM harness connectors.
Measure the resistance of the Sensor Ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

Replace and program the PCM in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Repair the Sensor Ground circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

8

Turn the ignition off.
Remove and inspect the Water In Fuel Lamp bulb.
Is the bulb OK?

All

Yes

Replace the Instrument Cluster.
Perform ROAD TEST VERIFICATION - VER-2.

No

Replace the Water In Fuel Lamp bulb.
Perform ROAD TEST VERIFICATION - VER-2.

272

DRIVEABILITY - DIESEL

*CHECKING THE WATER IN FUEL LAMP OPERATION —

Continued

Symptom:

P1655-AC CONTROL OPEN CIRCUIT - DIESEL

When Monitored and Set Condition:

P1655-AC CONTROL OPEN CIRCUIT - DIESEL

When Monitored:

With the ignition on.

Set Condition:

With the A/C clutch operation not requested, the ECM detects low voltage

on the A/C Clutch Relay Control circuit. NOTE: AC is an option that may not be present
on all vehicles.

POSSIBLE CAUSES

INTERMITTENT CONDITION

ASD/DIESEL POWER RELAY OUTPUT CIRCUIT OPEN

SUBSTITUTE A/C COMPRESSOR CLUTCH RELAY

A/C COMPRESSOR CLUTCH RELAY CONTROL CIRCUIT SHORTED TO GROUND

A/C COMPRESSOR CLUTCH RELAY CONTROL CIRCUIT OPEN

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, actuate the A/C Compressor Clutch Relay.
Is the A/C Compressor Clutch Relay clicking?

All

Yes

Go To

2

No

Go To

3

NOTE: Stop the A/C Compressor Clutch Relay actuation by the DRB.

2

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

273

HEATING & A/C

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Remove the A/C Compressor Clutch Relay from the PDC.
Turn the ignition on.
Using a 12-volt Test Light connected to ground, check the ASD/Diesel Power Relay
Output circuit.
Did the test light illuminate brightly?

All

Yes

Go To

4

No

Repair the ASD/Diesel Power Relay Output circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

4

Turn the ignition off.
Install a substitute relay in place of the A/C Compressor Clutch Relay.
Turn the ignition on.
With the DRB, actuate the A/C Compressor Clutch Relay.
Is the A/C Compressor Clutch clicking?

All

Yes

Replace the A/C Compressor Clutch Relay.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

5

5

Turn the ignition off.
Disconnect the ECM harness connector(s).
Remove the A/C Compressor Clutch Relay from the PDC.
Measure the resistance between ground and the A/C Compressor Clutch Relay
Control circuit.
Is the resistance above 100 kohms?

All

Yes

Go To

6

No

Repair the A/C Compressor Clutch Relay Control circuit for a
short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

6

Turn the ignition off.
Disconnect the ECM harness connector(s).
Remove the A/C Compressor Clutch Relay from the PDC.
Measure the resistance of the A/C Compressor Clutch Relay Control circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

7

No

Repair the A/C Compressor Clutch Relay Control circuit for an
open.
Perform ROAD TEST VERIFICATION - VER-2.

7

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

274

HEATING & A/C

P1655-AC CONTROL OPEN CIRCUIT - DIESEL —

Continued

Symptom:

P1655-AC CONTROL SHORT CIRCUIT - DIESEL

When Monitored and Set Condition:

P1655-AC CONTROL SHORT CIRCUIT - DIESEL

When Monitored:

With the ignition on.

Set Condition:

The ECM detects excessive current draw on the A/C clutch relay control

circuit when attempting to activate the A/C clutch. NOTE: AC is an option that may not be
present on all vehicles.

POSSIBLE CAUSES

INTERMITTENT CONDITION

SUBSTITUTE A/C COMPRESSOR CLUTCH RELAY

A/C COMPRESSOR CLUTCH RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, actuate the A/C Compressor Clutch Relay.
Is the A/C Compressor Clutch Relay clicking?

All

Yes

Go To

2

No

Go To

3

NOTE: Stop the A/C Compressor Clutch Relay actuation by the DRB.

2

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

275

HEATING & A/C

 

 

 

 

 

 

 

Content   ..  677  678  679  680   ..