Jeep Grand Cherokee WJ. Manual - part 533

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  531  532  533  534   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 533

 

 

(3) Remove hood hinge prop rod.
(4) Remove nuts attaching hinge to hood (Fig. 4).
(5) Remove bolts attaching hinge to body.
(6) Separate hinge from vehicle.

INSTALLATION

(1) Position hinge on vehicle and align reference

marks.

(2) Install bolts attaching hinge to body.
(3) Install nuts attaching hinge to hood.
(4) Install hood hinge prop rod.

HOOD LATCH

REMOVAL

(1) Remove nuts attaching latch to radiator cross-

member support (Fig. 5).

(2) Disconnect hood release cable from latch.
(3) Separate latch from vehicle.

INSTALLATION

(1) Connect latch release cable to latch.
(2) Position latch on radiator crossmember sup-

port.

(3) Install nuts attaching latch to radiator cross-

member support. Tighten nuts to 11 N·m (8 ft. lbs.)
torque.

HOOD RELEASE CABLE

REMOVAL

(1) Disconnect cable from hood latch (Fig. 6).
(2) Disconnect cable from retaining clips on left

inner fender panel.

(3) Remove left cowl side trim panel.

(4) Remove fasteners attaching cable bracket to

cowl side panel (Fig. 7).

(5) Route cable through dash panel and remove it

from under instrument panel.

INSTALLATION

(1) Route cable through hole in dash panel into

engine compartment.

(2) Pull cable forward and seat grommet in dash

panel.

(3) Position cable bracket on cowl side panel and

install fasteners.

(4) Install left cowl side trim panel.
(5) Route and install cable in retaining clips on left

inner fender panel.

(6) Connect cable to hood latch.

Fig. 4 Hood Support Prop

1 – HOOD
2 – COVER
3 – HINGE
4 – PROP

Fig. 5 Hood Latch

1 – HOOD RELEASE CABLE
2 – LATCH
3 – BUMPER

Fig. 6 Hood Latch

1 – HOOD LATCH
2 – HOOD RELEASE CABLE

23 - 30

BODY

WJ

REMOVAL AND INSTALLATION (Continued)

COWL PLENUM SEAL

REMOVAL

(1) Raise hood.
(2) Pull cowl plenum seal from cowl.
(3) Separate cowl plenum seal from cowl (Fig. 8).

INSTALLATION

(1) Position cowl plenum seal on cowl.
(2) Press cowl plenum seal to seat.

COWL COVER

REMOVAL

(1) Remove wiper arms.
(2) Remove plenum seal.

(3) Remove plastic push nuts attaching cowl cover

to cowl (Fig. 9).

(4) Remove windshield washer tubes at connector.
(5) Remove cowl cover from cowl.

INSTALLATION

(1) Position cowl cover on cowl.
(2) Install windshield washer tubes at connector.
(3) Install plastic push nuts attaching cowl cover

to cowl.

(4) Install plenum seal.
(5) Install windshield wiper arms.

EXTERIOR NAMEPLATES

REMOVAL

NOTE: Exterior nameplates are attached to body
panels with adhesive tape.

(1) Apply a length of masking tape on the body,

parallel to the top edge of the nameplate to use as a
guide, if necessary.

(2) If temperature is below 21°C (70°F) warm

emblem with a heat lamp or gun. Do not exceed 52°C
(120°F) when heating emblem.

(3) Insert a plastic trim stick or a hard wood

wedge behind the emblem to separate the adhesive
backing from the body.

(4) Clean adhesive residue from body with MOPAR

Super Clean solvent or equivalent.

INSTALLATION

(1) Remove protective cover from adhesive tape on

back of emblem.

(2) Position emblem properly on body (Fig. 10).

Fig. 7 Hood Release Cable

1 – LOWER COWL
2 – HOOD RELEASE CABLE
3 – RELEASE HANDLE

Fig. 8 Cowl Plenum Seal

1 – PLENUM SEAL

Fig. 9 Cowl Cover

1 – PLASTIC NUT
2 – COWL COVER

WJ

BODY

23 - 31

REMOVAL AND INSTALLATION (Continued)

(3) Press emblem firmly to body with palm of

hand.

(4) If temperature is below 21°C (70°F) warm

emblem with a heat lamp or gun to assure adhesion.
Do not exceed 52°C (120°F) when heating emblem.

SIDE VIEW MIRROR

REMOVAL

(1) Remove door trim panel.
(2) Disengage power mirror harness connector, if

equipped.

(3) Remove mirror flag seal.
(4) Remove nuts attaching mirror to door (Fig. 11).
(5) Separate mirror from door.

INSTALLATION

(1) Position mirror on door. Verify that gasket seal

is properly positioned.

(2) Install nuts attaching mirror to door.
(3) Install mirror retaining nuts.
(4) Install mirror flag seal.
(5) Engage power mirror harness connector, if

equipped.

(6) Install door trim panel.

SIDE VIEW MIRROR GLASS

REMOVAL

(1) With damaged mirror still on vehicle, position

mirror glass down and centered.

(2) Position a wide leverage device between the

bottom edge of the glass and the mirror shell.

(3) Firmly apply pressure in an upward direction

until glass assembly disengages from adapter plate.

(4) Disconnect

the

heater

wire

terminal,

if

equipped, or the EC plug, if equipped.

INSTALLATION

(1) Connect the heater wire terminal or the EC

plug, if equipped.

(2) Position the replacement glass in the mirror

shell and align the four snap tabs with the four cav-
ities in the shell.

(3) Apply firm pressure inward until the replacement

glass assembly engages with the adapter plate. Correct
assembly will result in a firm click. Glass assembly
should exhibit even gaps to the shell when complete.

(4) Pull lightly on corners of glass assembly to ensure

all four snaps are engaged and there is no free play.

Fig. 10 Exterior Nameplates

Fig. 11 Side View Mirror

1 – SIDEVIEW MIRROR
2 – MIRROR FLAG SEAL
3 – CONNECTOR

23 - 32

BODY

WJ

REMOVAL AND INSTALLATION (Continued)

FRONT FENDER

REMOVAL

(1) Using a wax crayon or equivalent, mark posi-

tion of fender.

(2) Remove front fender liner.
(3) Pull back fascia and remove screws attaching

fender to fascia.

(4) Remove screws attaching lower fender bracket

located behind fascia.

(5) Remove screws attaching fender to rocker

panel (Fig. 12).

(6) Remove screws attaching rear of fender to

A-pillar brackets.

(7) Open hood.
(8) Loosen screw under hood hinge, attaching

fender to engine compartment rail.

(9) Remove screws attaching fender to engine com-

partment rail (Fig. 13).

(10) Right fender only:

(a) If equipped, remove radio antenna.

(11) Separate fender from body.

Fig. 12 Fender Mounting

1 – BODY
2 – FENDER

Fig. 13 Upper Fender Mounting

1 – FENDER
2 – BODY

WJ

BODY

23 - 33

REMOVAL AND INSTALLATION (Continued)

 

 

 

 

 

 

 

Content   ..  531  532  533  534   ..