Jeep Grand Cherokee WJ. Manual - part 529

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  527  528  529  530   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 529

 

 

(3) Push sunshade back and down through the

sunroof opening.

(4) Using a flat blade tool, put front guide blocks

into the sunshade track. By pushing the block
towards the center of the vehicle.

(5) Move the glass panel to approximately halfway

to the fully closed position.

(6) Push sunshade down until the sunshade clears

the glass then move sunshade rearward behind the
glass panel.

SUNROOF HOUSING ASSEMBLY

REMOVAL

(1) Move glass panel to the fully closed position.
(2) Disconnect battery negative cable.
(3) Recline both front seats.
(4) Remove overhead console.
(5) Remove headliner
(6) Disconnect the drain tubes from sunroof hous-

ing (Fig. 7).

(7) Loosen fasteners attaching sunroof housing

assembly.

(8) With the aid of a helper, remove fasteners

attaching sunroof housing assembly to roof panel.

INSTALLATION

(1) Raise the sunroof housing assembly and guide

into position and start fasteners (Fig. 7).

(2) Tighten the fasteners, front to rear, attaching

the sunroof module to roof panel. Tighten the fasten-
ers, front to rear, to 11 N·m (97 in. lbs.) torque.

(3) Connect the drain tubes to the sunroof housing.
(4) Set headliner into position.
(5) Connect express module, drive motor, and con-

trol switch wire connectors.

(6) Test sunroof operation, adjust as necessary.
(7) Finish installing the headliner.
(8) Connect battery negative cable.

ADJUSTMENTS

SUNROOF GLASS PANEL ADJUSTMENT

(1) Move the sunshade rearward to the open position.
(2) Move the sunroof glass panel to the fully closed

position.

(3) Loosen the forward screws on each side enough

to make the front adjustment.

(4) Adjust the front of the sunroof glass panel 1 mm

(1/32 inch) below the top surface of the roof panel.

(5) Tighten the front two screws.
(6) Loosen the rear screws on each side enough to

make the rear adjustment.

(7) Adjust the rear of the sunroof glass panel 1 mm

(1/32 inch) above the top surface of the roof panel.

(8) Tighten the rear two screws.
(9) Check for proper fit. If not OK, repeat glass

panel adjustment.

Fig. 6 Sunroof Drive Cable Timing

1 – MOVE DRIVER SLIDE FORWARD/AFT
2 – GAGE

Fig. 7 SUNROOF ASSEMBLY

1 – ROOF
2 – DRAIN HOSE
3 – CLAMP
4 – SUNROOF ASSEMBLY
5 – CLAMP
6 – DRAIN HOSE

23 - 14

BODY

WJ

REMOVAL AND INSTALLATION (Continued)

SEATS

TABLE OF CONTENTS

page

page

DESCRIPTION AND OPERATION

SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

REMOVAL AND INSTALLATION

FRONT BUCKET SEAT . . . . . . . . . . . . . . . . . . . . 15
BUCKET SEAT SIDE SHIELD . . . . . . . . . . . . . . . . 16
BUCKET SEAT TRACK ADJUSTER . . . . . . . . . . . 16
BUCKET SEAT RECLINER . . . . . . . . . . . . . . . . . . 16
BUCKET SEAT BACK. . . . . . . . . . . . . . . . . . . . . . 16
BUCKET SEAT HEAD RESTRAINT. . . . . . . . . . . . 17
BUCKET SEAT HEAD RESTRAINT SLEEVE. . . . . 18
BUCKET SEAT BACK COVER . . . . . . . . . . . . . . . 18
BUCKET SEAT CUSHION COVER . . . . . . . . . . . . 19
REAR SEAT CUSHION RELEASE LATCH . . . . . . 19

REAR SEAT CUSHION. . . . . . . . . . . . . . . . . . . . . 19
REAR SEAT CUSHION COVER . . . . . . . . . . . . . . 19
REAR SEAT BACK LATCH RELEASE HANDLE . . 20
REAR SEATBACK . . . . . . . . . . . . . . . . . . . . . . . . 21
REAR SEAT BACK LATCH/HINGE . . . . . . . . . . . . 21
REAR SEAT BACK COVER . . . . . . . . . . . . . . . . . 21
REAR SEAT HEAD REST. . . . . . . . . . . . . . . . . . . 22
REAR SEAT FOLDING HEAD REST RELEASE

KNOB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

REAR SEAT HEAD REST SLEEVE. . . . . . . . . . . . 22
REAR SEAT HEAD REST FOLDING

MECHANISM. . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DESCRIPTION AND OPERATION

SEATS

DESCRIPTION

Seat modules are made up of a seat frame, seat

cushion, seat back cushion, a covering material, and
the electrical components used for power operation, if
equipped. Some seat systems also contain seat belt
components and supplemental restraint systems.

OPERATION

Seat assemblies transport the occupants in comfort

and safety. Seat assemblies also help position occu-
pants correctly in the event of airbag deployment.
Seat cushions, coverings, and electrical components
are serviceable. Refer to the appropriate group in
this manual.

REMOVAL AND INSTALLATION

FRONT BUCKET SEAT

REMOVAL

(1) Move seat to full rearward position.
(2) Remove front bolts attaching seat to floor pan

(Fig. 1).

(3) Move seat to full forward position.
(4) Using a trim stick, pry cover from seat track

(power seat only).

(5) Remove rear bolts attaching seat to floor pan.
(6) If equipped, disconnect power seat wire har-

ness connector.

(7) Remove seat from vehicle.

INSTALLATION

(1) Position seat on floor pan.
(2) If equipped, connect power seat wire harness

connector.

(3) Install rear bolts attaching seat to floor pan.

Tighten bolts to 40 N·m (30 ft. lbs.) torque.

(4) If equipped, install cover on seat track.

Fig. 1 Front Bucket Seat

1 – POWER BUCKET SEAT
2 – FLOOR PAN
3 – SEAT TRACK COVER

WJ

BODY

23 - 15

(5) Move seat to full rearward position.
(6) Install front bolts attaching seat to floor pan.

Tighten bolts to 40 N·m (30 ft. lbs.) torque.

BUCKET SEAT SIDE SHIELD

REMOVAL

(1) Remove screws attaching side shield to seat

frame.

(2) Disconnect wire harness connectors from power

seat and power lumbar switches, if equipped.

(3) Separate side shield from seat.

INSTALLATION

(1) Position side shield on seat.
(2) Connect wire harness connectors to power seat

and power lumbar switches, if equipped.

(3) Install screws attaching side shield to seat

frame.

BUCKET SEAT TRACK ADJUSTER

REMOVAL

(1) Remove seat.
(2) Remove side shield.
(3) Remove nuts attaching seat track adjuster to

seat cushion frame (Fig. 2) and (Fig. 3). Roll cushion
trim cover up to access the two front nuts.

(4) Disengage clips attaching wire harness to

adjuster.

(5) Disengage seat memory module connector, if

equipped.

(6) Separate seat track from seat cushion frame.

INSTALLATION

(1) Transfer seat memory module, if equipped.
(2) Position seat track on seat cushion frame.
(3) Route harness through frame and engage clips

attaching wire harness to adjuster.

(4) Engage seat memory module connector, if

equipped.

(5) Install nuts attaching seat track adjuster to

seat cushion frame. Tighten nuts to 28 N·m (20 ft.
lbs.) torque.

(6) Install front edge of cushion trim cover.
(7) Install seat.

BUCKET SEAT RECLINER

REMOVAL

(1) Remove seat back.
(2) Disengage J-strap at base of seat back.
(3) Roll seat back cover upward to access bolts

attaching recliner to seat back frame.

(4) Remove bolts attaching recliner to seat back

frame.

(5) Separate recliner from seat back.

INSTALLATION

(1) Position recliner on seat back.
(2) Install bolts attaching recliner to seat back

frame. Tighten bolts to 28 N·m (20 ft. lbs.) torque.

(3) Roll seat back cover downward.
(4) Engage J-strap at base of seat back.
(5) Install seat back.

BUCKET SEAT BACK

REMOVAL

(1) Move seat to full rearward position.

Fig. 2 Seat Track Adjuster—Power

1 – BACK PANEL
2 – LUMBAR ASSEMBLY
3 – SEAT CUSHION FRAME
4 – POWER SEAT TRACK ADJUSTER
5 – POWER RECLINER
6 – SEAT CUSHION PAD
7 – SEAT BACK FRAME

23 - 16

BODY

WJ

REMOVAL AND INSTALLATION (Continued)

(2) Remove inboard bolt attaching seat back frame

to seat cushion frame.

(3) Move seat to full forward position.
(4) Move seat back to full recline position.
(5) Remove screws attaching seat side shield to

seat frame.

(6) Disconnect

wire

harness

connector

from

recliner motor, if equipped.

(7) From the underside of the seat, disconnect the

wire harness connector for the power lumber and/or
heated seat, if equipped.

(8) Remove outboard bolts attaching recliner to

seat cushion frame.

(9) Route the power lumber and/or heated seat

harness through the seat cushion cover, if equipped.

(10) Separate seat back from seat cushion.

INSTALLATION

(1) Position seat back on seat cushion.
(2) Route the power lumber and heater harness

through the seat cushion cover, if equipped.

(3) Install recliner bolts attaching seat back frame

to seat cushion frame. Tighten bolts to 28 N·m (20 ft.
lbs.) torque.

(4) Install the inboard bolt attaching seat back

frame to seat cushion frame. Tighten bolt to 47N·m
(35 ft.lbs.).

(5) Connect wire harness connector to recliner

motor and/or heated seat, if equipped.

(6) From the underside of the seat, connect the

power lumber and/or heated seat wire harness con-
nector to the seat harness, if equipped.

(7) Install screws attaching seat side shield to seat

frame.

BUCKET SEAT HEAD RESTRAINT

REMOVAL

(1) Depress head restraint release button and lift

head restraint to full up position.

(2) Using a small flat blade, depress tab on right

side head restraint release button and using your
hand, simultaneously press tab on left side head
restraint release button (Fig. 4) and pull head
restraint up to separate from seat back.

INSTALLATION

(1) Position head restraint in seat back, press tab

on left side head restraint release button and push
down head restraint to secure.

Fig. 3 Seat Track Adjuster — Manual

1 – MANUAL RECLINER
2 – SEAT CUSHION PAD
3 – SEAT BACK FRAME
4 – SEAT CUSHION FRAME
5 – MANUAL SEAT TRACK ADJUSTER

Fig. 4 Head Restraint

1 – HEAD RESTRAINT
2 – FLAT BLADE

WJ

BODY

23 - 17

REMOVAL AND INSTALLATION (Continued)

 

 

 

 

 

 

 

Content   ..  527  528  529  530   ..