Jeep Grand Cherokee WJ. Manual - part 42

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  40  41  42  43   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 42

 

 

(5) Install differential case in the housing. Ensure

that the differential bearing cups remain in position
on the differential bearings and that the preload
shims remain between the face of the bearing cup
and the housing. Also verify that the pick-up opening
of the Vari-lok

y plenum is at the bottom of the hous-

ing. Tap the differential case to ensure the bearings
cups and shims are fully seated in the housing.

(6) Install the bearing caps at their original loca-

tions (Fig. 37).

(7) Loosely install differential bearing cap bolts.
(8) Remove axle housing spreader.
(9) Tighten the bearing cap bolts to 77 N·m (57 ft.

lbs.) torque.

(10) Install the axle shafts.

DIFFERENTIAL SIDE BEARINGS

REMOVAL

(1) Remove differential case from axle housing.
(2) Remove the bearings from the differential case

with Puller/Press C-293-PA, Adapters 8353, and Plug
C-293-3 (Fig. 38).

INSTALLATION

If replacement differential side bearings or differ-

ential case are being installed, differential side bear-
ing shim requirements may change. Refer to the
Differential Bearing Preload and Gear Backlash pro-
cedures in this section to determine the proper shim
selection.

CAUTION: Be sure that the Vari-lok

Y

plenum is

fully seated against the differential case prior to
installing the ring gear side differential bearing.

(1) Using tool C-4340 with handle C-4171, install

differential side bearings (Fig. 39).

(2) Install differential case in axle housing.

VARI-LOK

PLENUM

REMOVAL

(1) Remove differential case from axle housing.
(2) Remove the bearing from the ring gear side of

the differential case with Puller/Press C-293-PA,
Adapter Blocks 8353, and Plug C-293-3 (Fig. 40).

(3) Remove the Vari-lok

y plenum from the differ-

ential case hub.

WARNING: Do not touch the Vari-lok

Y

tuning reed

valve located under the Vari-lok

Y

plenum on the

differential case. The metal is very sensitive and the
unit will not operate properly if the reed valve is
disturbed.

INSTALLATION

If a replacement differential side bearing is being

installed, differential side bearing shim requirements

Fig. 37 Differential Bearing Cap Reference Letters

1 – INSTALLATION REFERENCE LETTERS
2 – INSTALLATION REFERENCE LETTERS

Fig. 38 Differential Bearing Removal

1 – SPECIAL TOOL 8353
2 – BEARING
3 – DIFFERENTIAL
4 – SPECIAL TOOL C-293–3
5 – SPECIAL TOOL C-293–PA

3 - 114

226 RBA AXLE

WJ

REMOVAL AND INSTALLATION (Continued)

may change. Refer to the Differential Bearing Pre-
load and Gear Backlash procedures in this section to
determine the proper shim selection.

(1) Install a new Vari-lok

y plenum onto the differ-

ential case hub. The plenum is to be installed with
the rubber seal toward the differential case and the
raised metal tabs away from the differential case.

CAUTION: Be sure that the Vari-lok

Y

plenum is

fully seated against the differential case prior to
installing the ring gear side differential bearing.

(2) Using Installer C-4340 and Handle C-4171,

install differential side bearing (Fig. 41).

(3) Install differential in axle housing.

RING GEAR

NOTE: The ring and pinion gears are serviced as a
matched set. Do not replace the ring gear without
replacing the pinion gear.

REMOVAL

(1) Remove differential from axle housing.
(2) Place differential case in a suitable vise with

soft metal jaw protectors. (Fig. 42)

(3) Remove bolts holding ring gear to differential

case.

(4) Using a soft hammer, drive ring gear from dif-

ferential case (Fig. 42).

INSTALLATION

CAUTION: Do not reuse the bolts that held the ring
gear to the differential case. The bolts can fracture
causing extensive damage.

(1) Invert the differential case and start two ring

gear bolts. This will provide case-to-ring gear bolt
hole alignment.

(2) Invert the differential case in the vise.
(3) Install new ring gear bolts and alternately

tighten to 95–122 N·m (70–90 ft. lbs.) torque (Fig.
43).

(4) Install differential in axle housing and verify

gear mesh and contact pattern.

PINION GEAR

NOTE: The ring and pinion gears are serviced as a
matched set. Do not replace the pinion gear without
replacing the ring gear.

Fig. 39 Install Differential Side Bearings

1 – HANDLE C-4171
2 – DIFFERENTIAL
3 – BEARING
4 – TOOL C-4340

Fig. 40 Differential Bearing Removal

1 – SPECIAL TOOL 8353
2 – BEARING
3 – DIFFERENTIAL
4 – SPECIAL TOOL C-293–3
5 – SPECIAL TOOL C-293–PA

WJ

226 RBA AXLE

3 - 115

REMOVAL AND INSTALLATION (Continued)

REMOVAL

(1) Remove differential assembly from axle hous-

ing.

(2) Mark pinion yoke and propeller shaft for

installation alignment.

(3) Disconnect propeller shaft from pinion yoke.

Using suitable wire, tie propeller shaft to underbody.

(4) Using Holder 6958 to hold yoke and a short

length of 1 in. pipe, remove the pinion yoke nut and
washer (Fig. 44).

(5) Using Remover C-452 and Wrench C-3281,

remove the pinion yoke from pinion shaft (Fig. 45).

Fig. 41 Differential Side Bearing Installation

1 – HANDLE C-4171
2 – DIFFERENTIAL
3 – BEARING
4 – TOOL C-4340

Fig. 42 Ring Gear Removal

1 – CASE
2 – RING GEAR
3 – RAWHIDE HAMMER

Fig. 43 Ring Gear Bolt Installation

1 – TORQUE WRENCH
2 – RING GEAR BOLT
3 – RING GEAR
4 – CASE

Fig. 44 Pinion Yoke Holder

1 – 1 in. PIPE
2 – PINION YOKE
3 – SPECIAL TOOL 6958
4 – LOWER CONTROL ARM

3 - 116

226 RBA AXLE

WJ

REMOVAL AND INSTALLATION (Continued)

(6) Remove the pinion gear from housing (Fig. 46).

Catch the pinion with your hand to prevent it from
falling and being damaged.

(7) Remove the pinion seal with a slide hammer or

pry out with bar.

(8) Remove oil slinger, if equipped, and the front

pinion bearing.

(9) Remove the front pinion bearing cup with

Remover D-103 and Handle C-4171 (Fig. 47).

(10) Remove the rear bearing cup from housing

(Fig. 48). Use Remover C-4307 and Handle C-4171.

Fig. 45 Pinion Yoke Removal

1 – SPECIAL TOOL C-3281
2 – YOKE
3 – SPECIAL TOOL C-452

Fig. 46 Remove Pinion Gear

1 – RAWHIDE HAMMER

Fig. 47 Front Bearing Cup Removal

1 – REMOVER
2 – HANDLE

Fig. 48 Rear Bearing Cup Removal

1 – DRIVER
2 – HANDLE

WJ

226 RBA AXLE

3 - 117

REMOVAL AND INSTALLATION (Continued)

 

 

 

 

 

 

 

Content   ..  40  41  42  43   ..