Engine JAC HFC4DA1-2C. Manual - part 147

TR

TR

TR

TR Transmission

Transmission

Transmission

Transmission Shaft

Shaft

Shaft

Shaft

- 110 -

Removal/Installation

Removal/Installation

Removal/Installation

Removal/Installation

Transmission

Transmission

Transmission

Transmission shaft

shaft

shaft

shaft

Installation
Note:

Note:

Note:

Note:

Have marks properly aligned.

1.

Install the transmission shaft front flange onto
transmission.

2.

Install transmission shaft intermediate support onto the
intermediate support seat located on body bottom plate.

Note:

Note:

Note:

Note:

Don’t tighten bolt for the moment to facilitate
adjustment.

3.

Install transmission shaft rear flange with rear axle
flange.

�

Have two marks on flanges properly aligned.

�

Use new mounting bolts for transmission shaft.

4.

Tighten

mounting

bolts

for

transmission

shaft

intermediate bearing after alignment of transmission
shaft.

FAX

FAX

FAX

FAX Front

Front

Front

Front Suspension

Suspension

Suspension

Suspension

---- 111

111

111

111 ----

Front

Front

Front

Front Suspension

Suspension

Suspension

Suspension

Applied models: SUNRAY products manufactured by JAC

Subject

Page

Instruction

Instruction

Instruction

Instruction and

and

and

and Operation

Operation

Operation

Operation

Front Suspension..........................................................................................................................................................112

Front Suspension.....................................................................................................................................................112

Diagnosis

Diagnosis

Diagnosis

Diagnosis and

and

and

and Testing

Testing

Testing

Testing

Front Suspension..........................................................................................................................................................114

Inspection and Confirmation...................................................................................................................................114
Fault symptom Table...............................................................................................................................................115

Removal

Removal

Removal

Removal and

and

and

and Installation

Installation

Installation

Installation

Removal and Installation of Subframe......................................................................................................................... 116

Specification

Specification

Specification

Specification

Specification.................................................................................................................................................................131

Tightening Torques................................................................................................................................................. 131

FAX

FAX

FAX

FAX Front

Front

Front

Front Suspension

Suspension

Suspension

Suspension

---- 112

112

112

112 ----

Instruction

Instruction

Instruction

Instruction and

and

and

and Operation

Operation

Operation

Operation

Front

Front

Front

Front Suspension

Suspension

Suspension

Suspension

This front axle is a steering axle at front of the vehicle,
mainly consisting of the front overhang subframe
assembly, lower swing arm assembly, front anti-roll bar
link assembly, steering knuckle with brake assembly,

helical spring assembly and mounting cushion for
helical spring, etc., realizing vehicle steering via vehicle
steering gear by pushing steering knuckle that may
make wheels to deflect with certain angle.

FAX

FAX

FAX

FAX Front

Front

Front

Front Suspension

Suspension

Suspension

Suspension

-113

113

113

113 -

SN

Name

Quantity

Remarks

1

Front helical spring assembly

2

2

Mounting cushion for front helical spring

2

3

Left lower swing arm weld assembly

1

4

Right lower swing arm weld assembly

1

5

Lower swing arm bushing assembly

2

6

Lower swing arm ball pin assembly

2

7

Taper washer(16X61X3)

2

8

Front shock absorber assembly

2

9

Brake hose mounting flat spring nut

2

10

Front anti-roll bar assembly

1

11

Front anti-roll bar mounting bushing

2

12

Front anti-roll bar mounting bracket

2

13

Front anti-roll bar link assembly

2

14

Type 1 all-metal hexagon lock nut (thickness

15.5)

2

15

Hexagon headed bolt

6

16

All-metal hexagon flange face lock nut

12

17

Hexagon flange face lock nut (length of screw

thread is 57)

2

18

Type 1 all-metal hexagon lock nut

2

19

Hexagon headed bolt (length of screw thread is

78)

2

Grade 10.9

20

All-metal hexagon flange face lock nut

2

21

Hexagon headed bolt and flat washer assembly

8

22

Hexagon lobular socket pan head screw

2