Infiniti G35 (V35) Sedan. Manual - part 1405

 

  Index      Infiniti     Infiniti G35 (V35) Sedan - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1403  1404  1405  1406   ..

 

 

Infiniti G35 (V35) Sedan. Manual - part 1405

 

 

TM-312

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

12. Install D-rings in reverse brake piston.

13. Install reverse brake piston in transmission case.

14. Install needle bearing to drum support edge surface.

CAUTION:

Take care with the direction of needle bearing. Refer to 

TM-

289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"

.

15. Install seal rings to drum support.

16. Install spring retainer and return spring in transmission case.

SCIA6330E

SCIA2325E

SCIA2796E

SCIA3333E

SCIA2324E

TRANSMISSION ASSEMBLY

TM-313

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

17. Set the SST on spring retainer and install snap ring (fixing spring

retainer) in transmission case while compressing return spring.

CAUTION:

Securely assemble them using a flat-bladed screwdriver so
that snap ring tension is slightly weak.

18. Install reverse brake drive plates, driven plates, dish plates and

retaining plate in transmission case.

CAUTION:

Take care with order of plates.

SCIA5877E

1

:  Snap  ring

2

: Retaining plate

3

: Drive plate

4

: Driven plate

5

: Dish plate

Drive plate / 
Driven plate

: 6/6

SCIA6949E

TM-314

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

19. Assemble N-spring.

20. Install reverse brake retaining plate in transmission case.

21. Install snap ring in transmission case.

22. Measure clearance between retaining plate and snap ring. If not

within specified clearance, select proper retaining plate.

23. Install needle bearing to transmission case.

CAUTION:

Take care with the direction of needle bearing. Refer to 

TM-

289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"

.

SCIA5249E

SCIA2439E

Specified clearance “A”

Standard: 

TM-354, "Reverse Brake"

.

Retaining plate: Refer to 

TM-354, "Reverse Brake"

SCIA3129E

SCIA5031E

TRANSMISSION ASSEMBLY

TM-315

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

24. Install revolution sensor to transmission case. Tighten revolution

sensor bolt to the specified torque.

CAUTION:

• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front

edge magnetic area.

• Do not place in an area affected by magnetism.

25. As shown in the figure, use the drift to drive rear oil seal into the

rear extension (2WD) or adapter case (AWD) until it is flush.

CAUTION:

• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.

26. Install return spring (1) to parking pawl (2).

27. Install parking pawl (with return spring) and pawl shaft to rear

extension (2WD) or adapter case (AWD).

SCIA2320E

SCIA5477E

SCIA6180J

SCIA3424E

 

 

 

 

 

 

 

Content   ..  1403  1404  1405  1406   ..