Infiniti G20 (P11). Manual - part 426

 

  Index      Infiniti     Infiniti G20 (P11) - service repair manual 1999-2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  424  425  426  427   ..

 

 

Infiniti G20 (P11). Manual - part 426

 

 

8

CHECK ACTUATORS

Refer to the following chart and confirm discharge air flow, air temperature, blower motor voltage and compressor opera-
tion.
Checks must be made visually, by listening to any noise, or by touching air outlets with your hand, etc. for
improper operation.

MTBL0375

MTBL0128

OK or NG

OK

©

GO TO 9.

NG

©

I

Air outlet does not change.
Go to “Mode Door Motor” (HA-48).

I

Intake door does not change.
Go to “Intake Door Motor” (HA-58).

I

Blower motor operation is malfunctioning.
Go to “Blower Motor” (HA-65).

I

Magnet clutch does not engage.
Go to “Magnet Clutch” (HA-73).

I

Discharge air temperature does not change.
Go to “Air Mix Door Motor” (HA-54).

GI

MA

EM

LC

EC

FE

CL

MT

AT

AX

SU

BR

ST

RS

BT

SC

EL

IDX

TROUBLE DIAGNOSES

AUTO

Self-diagnosis (Cont’d)

HA-35

9

STEP 5 - TEMPERATURE OF EACH SENSOR IS CHECKED

Press

(HOT) switch.

Code No.

appears on the display.

RHA492A

©

GO TO 10.

10

CHECK AMBIENT SENSOR

Press

(DEF) switch one time, temperature detected by ambient sensor is indicated on the display.

NOTE:
If temperature shown on display greatly differs from actual temperature, check sensor circuit first, then inspect sensor.

RHA499G

OK or NG

OK

©

GO TO 11.

NG

©

Go to Ambient Sensor Circuit (HA-92).

TROUBLE DIAGNOSES

AUTO

Self-diagnosis (Cont’d)

HA-36

11

CHECK IN-VEHICLE SENSOR

Press

(DEF) switch the second time, temperature detected by in-vehicle sensor is indicated on the display.

NOTE:
If temperature shown on display greatly differs from actual temperature, check sensor circuit first, then inspect sensor.

RHA500G

OK or NG

OK

©

GO TO 12.

NG

©

Go to In-vehicle Sensor Circuit (HA-95).

12

CHECK INTAKE SENSOR

Press

(DEF) switch the third time, temperature detected by intake sensor is indicated on the display.

NOTE:
If temperature shown on display greatly differs from actual temperature, check sensor circuit first, then inspect sensor.

RHA500G

OK or NG

OK

©

1. Press

(DEF) switch the fourth time. Display returns to original presentation 5.

2. Turn ignition switch OFF or

(AUTO) switch ON.

3. END

NG

©

Go to Intake Sensor Circuit (HA-102).

GI

MA

EM

LC

EC

FE

CL

MT

AT

AX

SU

BR

ST

RS

BT

SC

EL

IDX

TROUBLE DIAGNOSES

AUTO

Self-diagnosis (Cont’d)

HA-37

13

CHECK MALFUNCTIONING SENSOR

Refer to the following chart for malfunctioning code No.
(If two or more sensors malfunction, corresponding code Nos. blink respectively two times.)

MTBL0083

*1: Conduct self-diagnosis STEP 2 under sunshine.
When conducting indoors, aim a light (more than 60W) at sunload sensor, otherwise Code No.

will indicate despite that

sunload sensor is functioning properly.
*2: HA-92
*3: HA-95
*4: HA-102
*5: HA-99
*6: HA-104

RHA455G

RHA501A

©

INSPECTION END

TROUBLE DIAGNOSES

AUTO

Self-diagnosis (Cont’d)

HA-38

 

 

 

 

 

 

 

Content   ..  424  425  426  427   ..